Alvarion Technologies IF-MMDS1 Outdoor MDS transceiver User Manual BST 2 5 27
Alvarion Ltd. Outdoor MDS transceiver BST 2 5 27
Contents
- 1. User manual 1
- 2. User manual 2
- 3. Corrected user manual 1 of 2
- 4. Corrected user manual 2 of 2
- 5. New Sept 24 outdoor user manual
Corrected user manual 2 of 2
![BreezeACCESS MMDSBase Station EquipmentInstallationManualJuly, 2000Cat. No. 213101](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-1.png)
![Front MatterBS Equipment Installation Manual ii BreezeACCESS MMDS Series© 2000 by BreezeCOM Ltd. All rights reserved.No part of this publication may be reproduced in any material form without the written permission ofthe copyright owner.Trade NamesBreezeACCESS, BreezeNET, BreezeLINK, BreezeVIEW, BreezeMANAGE and WIX are tradenames of BreezeCOM Ltd. Other brand and product names are registered trademarks or trademarks oftheir respective companies.Statement of ConditionsThe information contained in this manual is subject to change without notice. BreezeCOM shall not beliable for errors contained herein or for incidental or consequential damages in connection with thefurnishing, performance, or use of this manual or equipment supplied with it.WarrantyIn the following warranty text, “the Company” shall mean:• BreezeCOM Ltd., for products located outside the USA.• BreezeCOM Inc., for products located in the USA.This BreezeACCESS product is warranted against defects in material and workmanship for a period ofone year from date of purchase. During this warranty period the Company will, at its option, eitherrepair or replace products that prove to be defective.For warranty service or repair, the product must be returned to a service facility designated by theCompany. Authorization to return products must be obtained prior to shipment. The buyer shall pay allshipping charges to the Company and the Company shall pay shipping charges to return the product tothe buyer.The Company warrants that the firmware designed by it for use with the unit will execute itsprogramming instructions when properly installed on the unit. The Company does not warrant that theoperation of the unit or firmware will be uninterrupted or error-free.Limitations of WarrantyThe foregoing warranty shall not apply to defects resulting from improper or inadequate maintenanceby the buyer, buyer supplied interfacing, unauthorized modification or misuse, operation outside of theenvironmental specifications for the product, or improper site preparation or maintenance. No otherwarranty is expressed or implied. The Company specifically disclaims the implied warranties ofmerchantability and fitness for any particular purpose.BreezeCOM shall not be liable to any person for any special or indirect damages, including, but not](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-2.png)
![Front MatterBreezeACCESS MMDS Series iii BS Equipment Installation Manuallimited to, loss of profits or revenues, loss of use or damage to any associated equipment, cost ofcapital, cost of substitute products, facilities or services, downtime costs or claims resulting from anycause whatsoever arising from or in any way connected with the manufacture, sale, handling, service,repair, maintenance or use of the products. In no event shall the company’s liability exceed thepurchase price denoted on the invoice.Information to UserAny changes or modifications of equipment not expressly approved by the manufacturer could voidthe user’s authority to operate the equipment.Safety ConsiderationsFor the following safety considerations, “Instrument” means the BreezeACCESS Base Stationequipment components and cables.CautionTo avoid shock, do not perform any servicing unless you are qualified to do so.To comply with FCC RF exposure requirements in section 1.1307, a minimum separation distance of64 cm (26 inches) is required between this antenna and all persons.Line VoltageBefore connecting this instrument to the power line, make sure that the voltage of the power sourcematches the requirements of the instrument.RadioThe instrument transmits radio energy during normal operation. To avoid possible harmful exposure tothis energy, do not stand or work for extended periods of time in front of its antenna. The long-termcharacteristics or the possible physiological effects of Radio Frequency Electromagnetic fields havenot been yet fully investigated.Antenna Installation and GroundingBe sure that the Outdoor unit, the antenna and the supporting structure are properly installed toeliminate any physical hazard to either people or property. Verify that the antenna mast is grounded soas to provide protection against voltage surges and static charges. Make sure that the installation of theantenna and cable is performed in accordance with all relevant national and local building and safetycodes.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-3.png)
![BreezeACCESS MMDS Series v SU A/E Subscriber Units Installation ManualTable of Contents1. INTRODUCTION.....................................................................................................................12. BASIC INSTALLATION.........................................................................................................22.1 Packing List – Modular Shelf Equipment.............................................................................22.1.1 BS-SH Base Station Shelf..............................................................................................22.1.2 AU-A/E-BS Access Units (up to six per shelf) .............................................................22.1.3 BS-PS Power Supply (one or two per shelf).................................................................. 22.2 Packing List – Stand-alone AU-A/E-NI Access Unit...........................................................32.3 Other Items Required for Installation ...................................................................................32.4 Guidelines for Selection of Equipment Location..................................................................32.5 Installing the Outdoor Radio Unit.........................................................................................62.5.1 Mounting the Outdoor Unit ...........................................................................................62.5.2 Connecting the Antenna Cable (AU-RE) ...................................................................... 82.5.3 Connecting the Ground and IF Cables...........................................................................82.6 Installing the Modular Shelf Indoor Equipment ...................................................................92.6.1 BS-SH Slot Assignments...............................................................................................92.6.2 The BS-AU ..................................................................................................................102.6.3 The BS-PS ...................................................................................................................122.6.4 Shelf and Modules Installation Procedure...................................................................132.7 Installing the AU-NI Indoor Unit........................................................................................ 143. CONFIGURING SYSTEM PARAMETERS .......................................................................153.1 Getting Started with the Local Terminal.............................................................................153.2 Configuration Parameters ...................................................................................................173.3 Reset Unit............................................................................................................................19](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-5.png)
![Table of ContentsBS Equipment Installation Manual vi BreezeACCESS MMDS Series4. VERIFYING CORRECT OPERATION..............................................................................204.1 Verifying Correct Operation of the AU-A/E-BS ................................................................ 204.2 Verifying Correct Operation of the AU-A/E-NI................................................................. 204.3 Verifying Correct Operation of the Outdoor Unit...............................................................215. SPECIFICATIONS.................................................................................................................225.1 Radio................................................................................................................................... 225.2 Outdoor Unit to Indoor Unit Communication..................................................................... 225.3 Configuration and Management.......................................................................................... 235.4 Interfaces............................................................................................................................. 235.5 Electrical .............................................................................................................................245.6 Mechanical..........................................................................................................................245.7 Environmental..................................................................................................................... 245.8 Standards Compliance, General..........................................................................................24APPENDIX A. USING TELNETAPPENDIX B. MMDS CHANNELS AND FREQUENCIES](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-6.png)
![Table of ContentsBreezeACCESS UMDS Series vii BS Equipment Installation ManualTable of FiguresFigure 2-1. Holes/Grooves/Screw Holes...................................................................................6Figure 2-2. AU-RE 3" Pole Mounting Installation Using the Supplied Brackets..................... 7Figure 2-3. AU-RA/AU-RE Radio Unit Bottom Panel.............................................................. 8Figure 2-4. Shelf Slot Assignments ..........................................................................................9Figure 2-5. BS-AU Front panel...............................................................................................10Figure 2-6. BS-PS Front Panel................................................................................................12Figure 2-7. AU -NI Rear Panel ................................................................................................14Figure 2-8. AU -NI Front Panel ...............................................................................................14Figure 3-1. Main Menu ...........................................................................................................16Figure 3-2. Basic Configuration Menu ...................................................................................18Table of TablesTable 2-1: IF Cables...................................................................................................................4Table 2-2: BS-AU LEDs.........................................................................................................11Table 2-3: BS-PS Power Supply LEDs.................................................................................... 12Table 4-1: AU-NI LEDs...........................................................................................................20Table 4-2: AU-RA/RE LEDs...................................................................................................21](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-7.png)
![IntroductionBreezeACCESS MMDS Series 1 BS Equipment Installation Manual1. INTRODUCTIONThis manual describes installation guidelines for BreezeACCESS MMDS basestation equipment, including the stand-alone AU-E/A-NI-MMDS Access Unitsand the modular AU-E/A-BS-MMDS Units with the BS-SH rack mounted shelf.The BreezeACCESS IP Broadband Wireless Local Loop (WLL) system allowsaccess service providers to provide high-speed IP connectivity services to theirsubscribers. To support IP-based services effectively BreezeACCESS systemsemploy wireless packet data switching technology.The BreezeACCESS MMDS line of products uses Frequency Hopping SpreadSpectrum radios that operate in Time Duplex Division (TDD) mode in the2.500GHz – 2.686GHz frequency range.The AU-A/E-NI and the AU-A/E-BS Access Units are comprised of an indoorunit and an outdoor unit. In the AU-A-NI and AU-A-BS products, the outdoorunit (AU-RA) contains the radio module and an integral flat antenna. In theAU-E-NI and AU-E-BS products, the outdoor unit (AU-RE) contains the radiomodule and an interface to an external antenna (not included).The indoor unit of the AU-A/E-NI is a stand-alone unit (AU-NI) that is poweredfrom the mains via its AU-PS power supply unit. The indoor unit of the AU-A/E-BS is a module (BS-AU) that is designed for insertion into the BS-SH shelf. TheBS-SH, which is a 3U shelf suitable for installation in 19 racks, can contain upto six BS-AU active modules and one or two BS-PS power supply modules. Theshelf is powered from a –48VDC power source. Power supply redundancy issupported through the optional use of a second BS-PS power supply module.The indoor unit provides the interface to the network. It also contains an IF(Intermediate Frequency) module and is connected to the outdoor unit via a50-ohm coaxial IF cable. The IF cable serves for transmission of the 440MHz IFsignal between the indoor and the outdoor units. It also serves for transferringpower (12VDC), management and control signals from the indoor unit to theoutdoor unit.Note: The information contained in this manual is applicable toBreezeACCESS MMDS units with software release 2.5.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-9.png)
![Basic InstallationBS Equipment Installation Manual 2 BreezeACCESS MMDS Series2. BASIC INSTALLATION2.1 Packing List – Modular Shelf Equipment2.1.1 BS-SH Base Station Shelf• BS-SH shelf (with blank panels)• Rubber legs for optional desktop installationNote: Unless ordered otherwise, each BS-SH will be shipped with one BS-PSpower supply installed.2.1.2 AU-A/E-BS Access Units (up to six per shelf)• Outdoor unit:⇒ AU-RA with integral antenna or⇒ AU-RE with a connector to an external antenna (not included)• Pole mounting kit for the outdoor unit (with two brackets, four sets ofscrews, nuts and washers)• BS-AU Network Interface module• Monitor cable2.1.3 BS-PS Power Supply (one or two per shelf)• BS-PS Power Supply module• Power cable](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-10.png)
![Basic InstallationBreezeACCESS MMDS Series 3 BS Equipment Installation Manual2.2 Packing List – Stand-alone AU-A/E-NI Access Unit• AU-NI indoor unit• Outdoor unit:⇒ AU-RA with integral antenna or⇒ AU-RE with a connector to an external antenna (not included)• AU-PS power supply with a mains power cord• Pole mounting kit for the Outdoor unit (with two brackets, four sets ofscrews, nuts and washers)• Wall mounting kit for the AU-NI unit2.3 Other Items Required for Installation• IF cable (s)* (one for each AU)• Grounding cable(s) with an appropriate termination (one for each AU)• Ethernet cable(s) (straight, one for each AU)• Antenna(s)* and RF cable(s)* (AU-E-NI or AU-E-BS only)• A portable PC with terminal emulation software• Installation tools and materials.Items marked with an asterisk (*) are available as options from BreezeCOM.2.4 Guidelines for Selection of Equipment LocationSelect appropriate locations for the equipment using the following guidelines:• The outdoor unit can be pole—or wall mounted. Its location should alloweasy access to the unit for installation and testing.• The AU-RA unit with its integrated antenna, or the external antennaconnected to the AU-RE unit, should be installed where it provides coverageof all subscriber units in the area it is intended to serve. The higher the AU-RA or the antenna, the better coverage it can provide.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-11.png)
![Basic InstallationBS Equipment Installation Manual 4 BreezeACCESS MMDS Series• The AU-RE outdoor unit should be installed as near as possible to itsantenna.Note: The distance between any two antennas should be greater than 40 cm.• The outdoor unit is connected to the indoor unit by means of a coaxial IFcable carrying signals, controls and power. The IF frequency is 440 MHz.The maximum allowed attenuation of the IF cable is 15dB and its maximumallowed DC resistance (the sum of the DC resistance of the inner and outerconductors) is 1.5 ohm. This allows for cable lengths of up to 30m whenusing the standard RG 58 cable. If longer cables are required, a cable withlower attenuation and/or DC resistance should be used. Table 2-1 provides data regarding several industry-standard cables such asRG 58 and RG 213. If the spectral environment is polluted with noise in the440 MHz band, it is recommended to use a higher quality double-shieldedcable such as LMR 240 or LMR 400 (manufactured by TimesCommunications). Table 2-1: IF Cables Cable Type RG 58 RG 213 LMR 240 LMR 400 Maximum cableLength (m) 30 100 65 150• The BS-SH and its modules and the SU-NI are designed for indooroperation, i.e., inside buildings, a suitable cabinet or a shelter. Airtemperature control might be necessary – the equipment is designed tooperate over the temperature range 0°C to 45°C.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-12.png)
![Basic InstallationBreezeACCESS MMDS Series 5 BS Equipment Installation ManualNote: Outdoor units and antennas should be installed ONLY by experiencedinstallation professionals who are familiar with local building and safetycodes and, wherever applicable, are licensed by the appropriate governmentregulatory authorities.The system complies with the ETS 300 385 standard and is protected againstsecondary lightning strikes when its outdoor unit is properly groundedaccording to the applicable country-specific industry standards forprotection of structures against lightning.Failure to do so may void the BreezeACCESS product warranty and mayexpose the end user or the service provider to legal and financial liabilities.BreezeCOM and its resellers or distributors are not liable for injury,damage or violation of regulations associated with the installation ofoutdoor units or antennas.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-13.png)
![Basic InstallationBS Equipment Installation Manual 6 BreezeACCESS MMDS Series2.5 Installing the Outdoor Radio Unit2.5.1 Mounting the Outdoor UnitThe outdoor unit can be secured to the pole using one of the following options:• Special brackets and open-ended screws (supplied with each unit). There aretwo pairs of screw holes, allowing use of the brackets with various polewidths.• U-bolts - size A (inner installation holes, up to 2" pole).• U-bolt - size B (outside installation holes, up to 3" pole).• Metal bands (9/16” wide, minimum 12” long).Figure 2-1 shows the locations of the holes, grooves and screw holes on the rearside of the unit.Figure 2-2 illustrates the method of installing an AU-RE unit on a pole using thesupplied brackets and open-ended screws. The installation of an AU-RA unitwith an integral antenna is very similar to the installation of an SU-RE unit.Note: Make sure to install the unit with the bottom panel (the panel with the IFconnector) facing downward.Bracket ScrewsGrooves for Insertion of 9/16” Metal BandU-Bolts (3” Pole)U-Bolts (2” Pole)Figure 2-1. Holes/Grooves/Screw Holes](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-14.png)
![Basic InstallationBreezeACCESS MMDS Series 7 BS Equipment Installation ManualFigure 2-2. AU-RE 3" Pole Mounting Installation Using the SuppliedBracketsNote: When inserting the open-ended screws, make sure to insert them with thegrooves pointing outwards; these grooves are intended to allow fastening ofthe screws with a screwdriver.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-15.png)
![Basic InstallationBS Equipment Installation Manual 8 BreezeACCESS MMDS Series2.5.2 Connecting the Antenna Cable (AU-RE)Connect an RF cable between the ANT connector (located on the top panel of theunit, marked ANT) and the antenna.2.5.3 Connecting the Ground and IF CablesThe Ground terminal (marked and the IF cable connector (marked IF) arelocated on the bottom panel of the Outdoor unit, shown in Figure 2-3.Figure 2-3. AU-RA/AU-RE Radio Unit Bottom Panel1. Connect one end of the grounding cable to the Ground terminal and connectthe other end to a good ground connection.2. Connect the coaxial cable to the IF connector. Verify that the length of the IFcable is sufficient and that it can easily reach the Indoor unit.Note: Make sure to switch OFF the power of the indoor unit prior toconnecting/disconnecting the IF cable.GroundScrew](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-16.png)
![Basic InstallationBreezeACCESS MMDS Series 9 BS Equipment Installation Manual2.6 Installing the Modular Shelf Indoor Equipment2.6.1 BS-SH Slot AssignmentsThe Base Station shelf has ten slots, as shown in Figure 2-4BS-AUMONIFETHBS-AUMONIFETHBS-AUMONIFETHBS-AUMONIFETHBS-AUMONIFETHBS-AUMONIFETHFigure 2-4. Shelf Slot AssignmentsThe two wide slots on the both sides of the shelf accommodate the BS-PS powersupply modules. The shelf is designed to support power supply redundancythrough the use of two Power Supply modules. If a single power supply is used,it can be inserted in any of the two available slots.The remaining eight slots can accommodate up to six active BS-AU modules.Two extra slots are for future use. Active BS-AU modules can be installed in anyof the 8 slots. Unused slots should be covered by blank panels.8 Middle slots - BS-AU modulesExtreme slots - Power Supply modules](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-17.png)
![Basic InstallationBS Equipment Installation Manual 10 BreezeACCESS MMDS Series2.6.2 The BS-AUThe BS-AU front panel is shown in Figure 2-5.BS-AUMONIFETH5(6(72))213:5$/50:/1.0$67(5Figure 2-5. BS-AU Front panelThe BS-AU provides the following interfaces:An Ethernet connector (ETH) for connecting the BS-AU to the network. Thisconnector should be connected to a straight Ethernet cable.An IF connector for connecting the BS-AU to an outdoor AU-RE or AU-RAradio unit. The outdoor radio unit provides the air link between the BS-AU andthe remote Subscriber Units.A MON connector for connecting an ASCII terminal with terminal emulationsoftware for configuration and maintenance purposes.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-18.png)
![Basic InstallationBreezeACCESS MMDS Series 11 BS Equipment Installation ManualThe BS-AU front panel LEDs are described in Table 2-2.Table 2-2: BS-AU LEDsName Description FunctionalityPWR Power supply12 VDC On – 12 VDC power is supplied to AU-REOff – 12 VDC power is not supplied to AU-REWLNK Wireless linkactivity Blinking –Receiving packet from the wireless linkOff – No reception of packets from the wirelesslinkALRM ALARMIndication On – Loss of hopping synchronization (slave units)MASTER MasterIndicationOn – The unit is configured as a MasterETHconnectorembeddedLEDEthernetactivityOn- Receive/Transmit on Ethernet portOff- No Receive/Transmit on Ethernet portETHconnectorembeddedLEDETH LinkIntegrityOn- Unit is connected to Ethernet segmentOff- Unit is not connected to Ethernet segmentThe switch on the BS-AU front panel controls the supply of 12 VDC power tothe outdoor unit via the IF cable. The momentary RESET position of this switchis for resetting the outdoor unit. In the OFF position, power is not supplied to theoutdoor unit, even when the BS-AU unit is still ON.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-19.png)
![Basic InstallationBS Equipment Installation Manual 12 BreezeACCESS MMDS Series2.6.3 The BS-PSThe BS-PS provides -48VDC to all the modules installed in the BS-SH rack. TheBS-PS front panel is shown in Figure 2-6.BS-PSOFFON-48V12V5VONPWRFigure 2-6. BS-PS Front PanelThe BS-AU provides a single connector for connecting the -48VDC powersource to the module. The color codes of the cable wires are:black -48VDCred + (Return)The switch turns the mains power to the power supply ON and OFF. Table 2-3: BS-PS Power Supply LEDs Name Description ON -48 VDC is available and Power Supply is ON 5V The 5V power supply module is OK 12V The 12V power supply module is OK](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-20.png)
![Basic InstallationBreezeACCESS MMDS Series 13 BS Equipment Installation Manual2.6.4 Shelf and Modules Installation Procedure1. Install the BS-SH rack in a 19” cabinet (or place on an appropriateshelf/table). When mounted the BS-SH on a desktop, screw on the rubberlegs shipped with unit.2. Carefully insert the BS-PS Power Supply and the BS-AU modules into theirintended slots and push firmly until they are securely locked; refer toSection 2.6.1 for a description of the slot assignments. Close the captivescrews attached to each module. Place blank covers over all the unused slots.3. Connect the IF cable(s) to the connector(s) marked IF located on the frontpanel(s) of the BS-AU module(s) shown in Figure 2-5. The other side of theIF cable is already connected to the outdoor unit.4. Connect the DC power cord to the –48 DC In jack (marked –48V) located onthe front panel of the BS-PS power supply shown in Figure 2-6. If aredundant power supply module is installed, connect a power cable to it aswell.5. Connect the power cord(s) to the –48VDC power source. Connect the blackwire to the -48VDC contact of the power source. Connect the red wire to the+ (Return) contact. Connect the shield to the Ground.6. Switch the BS-PS power supplies to ON. Verify that all the power indicatorLEDs on the BS-PS front panel are ON. Refer to Table 2-3 for a descriptionof these LEDs.7. Set the switches on the front panel of all BS-AU modules in the rack to ON.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-21.png)
![Basic InstallationBS Equipment Installation Manual 14 BreezeACCESS MMDS Series2.7 Installing the AU-NI Indoor Unit1. Place the AU-NI unit in an appropriate location on a shelf or a table. Theunit can be wall mounted using the installation materials provided with theunit. Use a 6mm (1/4”) drill and the supplied template plate for easy andaccurate marking of the holes.2. Connect the AU -PS power cord to the DC In jack (marked DC-12V) locatedon the rear panel of the Indoor unit (shown in Figure 2-6).3. Connect the IF cable to the IF connector (marked IF) on the rear panel of theIndoor unit. The other side of the IF cable should already be connected to theOutdoor unit.4. Connect the other end of the mains power cord to the AU -PS. Connect themains power plug to a mains power outlet.DC - 12V ETH IFFigure 2-7. AU -NI Rear Panel5. Verify that the Power LED (marked PWR) located on the front panel of theIndoor Unit is turned ON.PWRWLNKMONFigure 2-8. AU -NI Front Panel6. Use a straight Ethernet 10baseT cable to connect the base station network(e.g., a hub, switch or router) to the Ethernet port (marked ETH) located onthe rear panel of the AU-NI unit.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-22.png)
![Configuring System ParametersBreezeACCESS MMDS Series 15 BS Equipment Installation Manual3. CONFIGURING SYSTEM PARAMETERSAfter completing the installation process as described in the preceding section,proceed with configuration of the basic system parameters.This section covers the configuration of basic installation parameters. Refer tothe Administration Manual for information related to other parameters.Note: Optionally, the product can be configured using Telnet over the Ethernetport, after setting the IP address. See Appendix A of this manual for furtherinformation.3.1 Getting Started with the Local Terminal1. Connect one end of the Monitor cable to the MON jack on the front panel ofthe BS-AU module or the AU-NI unit. Connect the second end of the cableto the COM port of the terminal. The COM port connector on the Monitorcable is a 9 pin D-type plug.2. Run a terminal emulation program (e.g., ProComm or WindowsHyperTerminal) using the following setup:Baud rate 9600Data bits 8Stop bits 1Parity NoneFlow Control Xon/XoffConnector Available Com Port3. Press Enter. The Select Access Level menu appears. Select the access levelaccording to your authorized access level. You will be requested to enteryour password. After entering the correct password press the Enter key.The main menu appears as shown in Figure 3-1](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-23.png)
![Configuring System ParametersBS Equipment Installation Manual 16 BreezeACCESS MMDS SeriesSoftwareVersion No.BreezeACCESS/BST-AUOfficial Release Version – 2.5.3Release Date: Tue Jul 18 21:12:54 2000Main Menu=====================1 – Info Screens2 – Unit Control3 – Basic Configuration4 – Site Survey5 – Advanced ConfigurationBreezeACCESS >>>Figure 3-1. Main Menu The appearance of the displayed Main Menu varies in accordance with theaccess level.• For users with read only access rights, only the Info Screens option isdisplayed. Users with this access level cannot access the Unit Control,Basic Configuration, Site Survey and Advanced Configuration menus.• For users with Installer access rights, the first four menu items (InfoScreens, Unit Control, Basic Configuration and Site Survey) aredisplayed. Users with this access level cannot access the AdvancedConfiguration menu.• For users with Administrator access rights, the full Main Menu will bedisplayed. These users can access all the menu items.Unit TypeUnit Name](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-24.png)
![Configuring System ParametersBreezeACCESS MMDS Series 17 BS Equipment Installation Manual4. Operate the monitor program as follows:• Type an option number to open/activate the option. You may needto press the Enter key in some cases.• Press the Esc key to exit a menu or an option.• You can log-out and exit the monitor program at any time bysimultaneously pressing the Ctrl and X keys.• Reset the unit after making configuration changes for the new valuesto take effect.• You can view the current parameters’ configuration by selecting 1 inthe Main Menu to Access the Info Screens menu, and then selecting2 in the Info Screens menu to view the Basic Configurationparameters.3.2 Configuration ParametersThe following system parameters must be configured for each Access Unit:• ESSID• IP Address• Subnet Mask• Default Gateway Address• Hopping Band• Flexible sub-bands Definition (if Flexible Hopping was selected in theHopping Band menu)• Frequency Offset• Hopping Shift (if using two or more AUs)• Hopping Sync (if using two or more AUs)Note: You must select Reset Unit in the Unit Control menu for the changes to takeeffect.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-25.png)
![Configuring System ParametersBS Equipment Installation Manual 18 BreezeACCESS MMDS Series1. From the main menu, type 3 to access the Basic Configuration menu.BreezeACCESS/BST-AUOfficial Release Version – 2.5.3Release Date: Tue Jul 18 21:12:54 2000Basic Configuration====================1 – IP Address2 – Subnet Mask3 – Default Gateway Address4 – ESSID5 – Maximum Data Rate6 – Frequency OffsetH – Hopping BandF – Flexible sub-bands DefinitionX - Transmit Power ControlS - Show Basic ConfigurationBreezeACCESS >>>Figure 3-2. Basic Configuration Menu2. From the Basic Configuration menu, type 1 to access the IP Addressselection screen. Enter the required IP address.3. Type 2 to access the Subnet Mask selection screen. Enter the required subnetmask.4. Type 3 to access the Default Gateway Address selection screen. Enter therequired default gateway address.5. Type 4 to access the ESSID selection screen. Enter the required ESSID.6. Type H to access the Hopping Band menu. Enter the required hopping band.7. If Flexible Hopping was selected in the Hopping Band selection menu, typeF to access the Flexible sub-bands Definition menu. Use the Add/Delete sub-bands screens to define the required frequencies. See Appendix B for a list ofstandard frequencies.8. Type 6 to access the Frequency Offset selection screen. Enter the requiredfrequency offset.9. If more than one AU is used, they should be synchronized for optimalspectrum utilization. Type 7 to access the Hopping Shift selection screen and](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-26.png)
![Configuring System ParametersBreezeACCESS MMDS Series 19 BS Equipment Installation Manualenter the required shift. Type 8 to access the Hopping Sync selection screen.Enter the required hopping sync status (Master or Slave).Note: Only one AU should be defined as a Master. The other units should bedefined as slaves. If only one AU is used, it should be defined as Idle.3.3 Reset Unit1. From the main menu, type 2 to access the Unit Control menu.2. Type 1 to access the Reset Unit menu. Type 1 to reset the unit so that newconfiguration settings are applied.Note: Should you make any mistakes during configuration or encounter anyproblems associated with system configuration parameters, you mayconfigure the unit back to the factory defaults, as follows:Type 2 in the Unit Control menu to access the Set Factory Defaults menu.Type in 2 (Set Factory defaults-Full) to load the default values. Reset theunit for the factory defaults values to take effect.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-27.png)
![Verifying Correct OperationBS Equipment Installation Manual 20 BreezeACCESS MMDS Series4. VERIFYING CORRECT OPERATION4.1 Verifying Correct Operation of the AU-A/E-BSAfter completing the installation as described above, the system starts operation.To verify correct operation, view the LED indicators located on the front panel ofthe BS-AU modules as shown in Table 2-2 on page 11.Note: If the Access Units are not synchronized, reset the Master BS-AU unit andthen the Slave units to re-synchronize them.4.2 Verifying Correct Operation of the AU-A/E-NITo verify proper operation, view the LED indicators located on the front and rearpanels of the AU-NI unit as described in Table 4-1.Table 4-1: AU-NI LEDsName Description FunctionalityPWR Power Supply12VDC On – 12VDC power is supplied to the AU-NIOff –Power is not supplied to the AU-NIWLNK Wireless linkactivity Blinking –Receiving packet from thewireless linkOff – No reception of packets from thewireless linkETH connectorembedded LED Ethernetactivity On – Receive/transmit on Ethernet portOff – No receive/transmit on Ethernet portETH connectorembedded LED ETH Linkactivity On – Unit is connected to Ethernet segmentOff – Unit is not connected to Ethernetsegment](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-28.png)
![Verifying Correct OperationBreezeACCESS MMDS Series 21 BS Equipment Installation Manual4.3 Verifying Correct Operation of the Outdoor UnitTo verify proper operation, view the LED indicators located on the bottom panelof the Outdoor unit as shown in Figure 2-3 on page 8.Table 4-2 lists the various LED states.Table 4-2: AU-RA/RE LEDsName Description FunctionalityALARM AlarmIndication On – A problem with the power amplifier or inthe locking process of any of the synthesizersOff –Normal operation12V IN 12V DC powersupply On – 12VDC power is supplied to the unitOff – 12VDC is not availableETH Ethernetactivity Blinking – Data received from or transmitted toEthernet LANOff – No activity on the Ethernet LANNote: Verifying proper operation of the outdoor unit using the LEDs as describedabove is possible only after completion of the configuration process.](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-29.png)
![SpecificationsBS Equipment Installation Manual 22 BreezeACCESS MMDS Series5. SPECIFICATIONS5.1 RadioFrequency 2.500GHz –2.686GHzRadio Access Method FH-CDMA or TDMAOperation Mode Time Duplex DivisionChannel Bandwidth 2 MHzOutput Power (at antenna port)29 dBm typical. Power Control range – 20 dBSensitivity(dBm at antenna port, BER 1E10-6)1Mbps2Mbps3Mbps-93-86-77Data Rate 3Mbps maxModulation Multilevel GFSK5.2 Outdoor Unit to Indoor Unit CommunicationIF Frequency 440 MHzIF cable Impedance 50 ohmMaximum IF cable Attenuation 15dBMaximum IF cable DC Resistance 1.5 ohm](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-30.png)
![SpecificationsBreezeACCESS MMDS Series 23 BS Equipment Installation Manual5.3 Configuration and ManagementLocal Management Via MON port, Monitor program using terminalemulationRemote Management SNMP, Telnet, TFTPRemote Management Access From Wired LAN, Wireless LinkSNMP Agents MIB II, Bridge MIB, Private MIBsSecurity Authentication and filteringSoftware upgrade TFTP download5.4 InterfacesInterface Outdoor Unit Indoor EquipmentRF (AU-E) N-Type jack lightningprotectedIF TNC jack, lightningprotected TNC jack, lightning protectedEthernet 10BaseT (RJ-45) with two embedded LEDsMonitor 3 pin low profilePower 12 VDC via the IF cable 4-pin power connector (BS-PS), DC plug for the AU-PS power supply (AU-NI)](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-31.png)
![SpecificationsBS Equipment Installation Manual 24 BreezeACCESS MMDS Series5.5 ElectricalOutdoor Unit 12 VDC via the IF cableIndoor Modular Shelf Equipment -48 VDC, 200 W for a fully equipped shelf.AU (Indoor + Outdoor): 25WIndoor AU-NI Unit AU-NI: 12VDC/2.5A from AU-PSAU-PS: 100 - 240 VAC, 47-63 Hz5.6 MechanicalOutdoor Unit AU-RE: 30cm x 12cm x 5cm, 2.2 kg.AU-RA: Depending on specific model.Indoor Modular Shelf Equipment BS-SH: 19”,3U, depth 26cm, 6 kg. Fully loadedIndoor AU-NI Unit AU-NI: 13cm x 8.6cm x 3cm, 0.5 kg.AU-PS: 10cm x 6.5cm x 3.5cm, 0.4 kg.5.7 EnvironmentalOutdoor Unit Indoor EquipmentOperating Temperature -400C to 600C00C to 450COperating Humidity 5%-95% non condensingWeather protected 5%-95% non condensing5.8 Standards Compliance, GeneralEMC FCC part 15, FCC part 21Safety UL 1950Environmental GR - 63 - CORE (Bellcore)](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-32.png)
![SpecificationsBreezeACCESS MMDS Series 25 BS Equipment Installation ManualAPPENDIX A. USING TELNETUse the following procedure to connect to BreezeACCESS 3.5 units via a Telnetsession.1. Connect the PC to the Ethernet port of the unit (or the hub to which the unitis connected) using a straight Ethernet cable. If you connect the PC directlyto a unit that is normally connected to a hub, use a crossed Ethernet cable.You may also connect the PC to any Ethernet port on the network andcommunicate with the unit to be managed via the wired or wireless media.2. Make sure that the IP parameters of the PC are configured to enableconnectivity with the unit.3. Run a Telnet application and use the IP address of the unit to be managed asthe Host Name.4. Set Port to Telnet (this is the default).5. Set Terminal Type to VT100 (this is the default).6. Enter the Service Provider password.7. When the password is recognized, the following message is displayed: You have entered.8. Press Enter, the Breeze ACCESS Monitor is displayed on the screen.9. To exit the Telnet session, choose Disconnect from the Connect menu.(The session is terminated automatically, after a specific time of inactivitydetermined by the Log-out Timer).](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-33.png)
![Appendix BBS Equipment Installation Manual 26 BreezeACCESS MMDS SeriesAPPENDIX B. MMDS CHANNELS ANDFREQUENCIESChannelName FrequencyBand (MHz Low Frequency (MHz) High Frequency (MHz)Actual Value inAdd/DeleteSub-bandsmenuActual Value inAdd/DeleteSub-bandsmenuA1 2500 - 2506 2501.5 2501 2504.5 2504B1 2506 - 2512 2507.5 2507 2510.5 2510A2 2512 - 2518 2513.5 2513 2516.5 2516B2 2518 - 2524 2519.5 2519 2522.5 2522A3 2524 - 2530 2525.5 2525 2528.5 2528B3 2530 - 2536 2531.5 2531 2534.5 2534A4 2536 - 2542 2537.5 2537 2540.5 2540B4 2542 - 2548 2543.5 2543 2546.5 2546C1 2548 - 2554 2549.5 2549 2552.5 2552D1 2554 - 2560 2555.5 2555 2558.5 2558C2 2560 - 2566 2561.5 2561 2564.5 2564D2 2566 - 2572 2567.5 2567 2570.5 2570C3 2572 - 2578 2573.5 2573 2576.5 2576D3 2578 - 2584 2579.5 2579 2582.5 2582](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-34.png)
![Appendix BBreezeACCESS MMDS Series 27 BS Equipment Installation ManualChannelName FrequencyBand (MHz Low Frequency (MHz) High Frequency (MHz)Actual Value inAdd/DeleteSub-bandsmenuActual Value inAdd/DeleteSub-bandsmenuC4 2584 - 2590 2585.5 2585 2588.5 2588D4 2590 - 2596 2591.5 2591 2594.5 2594E1 2596 - 2602 2597.5 2597 2600.5 2600F1 2602 - 2608 2603.5 2603 2606.5 2606E2 2608 - 2614 2609.5 2609 2612.5 2612F2 2614 - 2620 2615.5 2615 2618.5 2618E3 2620 - 2626 2621.5 2621 2624.5 2624F3 2626 - 2632 2627.5 2627 2630.5 2630E4 2632 - 2638 2633.5 2633 2636.5 2636F4 2638 - 2644 2639.5 2639 2642.5 2642G1 2644 - 2650 2645.5 2645 2648.5 2648H1 2650 - 2656 2651.5 2651 2654.5 2654G2 2656 - 2662 2657.5 2657 2660.5 2660H2 2662 - 2668 2663.5 2663 2666.5 2666G3 2668 - 2674 2669.5 2669 2672.5 2672H3 2674 - 2680 2675.5 2675 2678.5 2678G4 2680 - 2686 2681.5 2681 2684.5 2684](https://usermanual.wiki/Alvarion-Technologies/IF-MMDS1.Corrected-user-manual-2-of-2/User-Guide-117131-Page-35.png)