Altai Technologies CX200 CX200 Outdoor 2x2 802.11ac Wave 2 AP User Manual CX200 Quick Setup Guide

Altai Technologies Limited CX200 Outdoor 2x2 802.11ac Wave 2 AP CX200 Quick Setup Guide

User Manual

Quick Setup Guide 1 Altai Technologies Ltd. All rights reserved Altai CX200 Outdoor 2x2 8 0 2 . 1 1 a c W a v e 2 AP _________________________________________________ Quick Setup Guide Version 1.1
Quick Setup Guide Altai Technologies Ltd. All rights reserved Pole Mount Hose Clamp Wall Mount Kit - Anchors x 2 - Screws x 2 Adhesive Label PoE Injector (Optional) Introduction Thank you for purchasing the Altai CX200 product. This guide provides instructions to install the product and set it up as AP with minimal effort. Package Contents 2 CX200 Main Unit Quick Setup Guide Detachable Antennae - 2.4GHz Antenna x 2 - 5GHz Antenna x 2
Quick Setup Guide 3 Altai Technologies Ltd. All rights reserved LED Indicator Hardware Overview LED Indicator Power Off AP powered off Flashing Red AP booting up Solid Red AP boot up finished and ready for service LAN (Ethernet) Off LAN disconnected Solid Green LAN connected Flashing Green Data Transmitting/Receiving 2.4 GHz/5G WiFi Radios (AP/Station/ Repeater/Bridge) Off Radio Disabled Solid Green 1. AP mode on but with no client association; OR 2. Station mode on but not connected to remote AP; OR 3. Repeater mode on but not connected to remote AP; OR 4. Bridge mode on but not connected to remote peer Flashing Green Data transmitting/receiving
Quick Setup Guide 4 Altai Technologies Ltd. All rights reserved Ethernet Port and RF Antenna Port 5GHz Dipole Antenna 2.4GHz Dipole Antenna NOTE: To ensure correct antenna connection, check the labels (2.4GHz/5GHz) printed on each antenna body and RF port for easy reference. 5GHz Dipole Antenna 2.4GHz Dipole Antenna Ethernet Port Ethernet Port: Used to connect to power source (see the Power Options in the later section) and provides 10/100/1000 Mbps network interface for LAN connection. RF Antenna Ports: Used to attach 2.4G and 5G antennae for 2x2 MIMO WiFi access coverage or bridge connection.
Quick Setup Guide 5 Altai Technologies Ltd. All rights reserved 1 Feed the end of the cable through the cap nut, sleeve holder, sealing sleeve as shown in the picture. Setup Preparation  Wire stripping tool and crimping tool  Screwdriver (Slot type and Phillips type)  Drill and drill bits  Computer with Web Browser: Google Chrome, Mozilla Firefox, or Microsoft Internet Explorer 8 (or above)  Two Cat 5e/6 Ethernet cables  802.3af-compliant PoE switch  AltaiCare account (Optional) for cloud AP management and user service Ethernet Cable Feed-Through Seal the RJ45 cable Connector with the provided cable gland. 3 Connect the cable to the Ethernet Port. 4 Tighten the cap nut. RJ45 Connector Sealing Sleeve Sleeve Holder Cap Nut 2 Crimp the Ethernet connector with the crimping tool.
Quick Setup Guide 6 Altai Technologies Ltd. All rights reserved Mounting Options Option 1: Pole Mount (For 1.5 to 2.5 inches of pole diameter) 1 Thread the open end of the hose clamp through the two slots of the mount base. 2 Determine where the AP is to be placed. Tighten the hose clamp to secure the base to the pole. 1 2
Quick Setup Guide 7 Altai Technologies Ltd. All rights reserved Option 2: Wall Mount 1 Determine where the AP is to be placed and use the adhesive label to mark location of the two mounting holes on the wall surface. 2 Use an appropriate drill bit to drill two holes, each with 1/3” (8.1mm) in diameter and 1” (26mm) deep, on the markings. 3 Remove the label. Drive the anchors into the holes and then the screws into the anchors. 4 Align the mounting slots with the screw heads and attach the AP to the wall in place. 1 2 3 4
Quick Setup Guide 8 Altai Technologies Ltd. All rights reserved Power Options and Cable Connection Instructions You can follow one of the options below for CX200 configuration as described in the following sections. Option 1: 802.3at-Compliant PoE switch 1. Connect the CX200 Ethernet port to an 802.3af-compliant PoE switch with an Ethernet Cable. 2. Connect a computer to the switch. 3. Make sure the Power LED turns into a solid light for AP configuration. Option 2: PoE Injector (Purchased separately) 1. Connect the PoE injector ports as described below via Ethernet Cables. - PoE Port: Go to CX200 - LAN Port: Go to a computer 2. Connect the PoE Injector to AC power socket using a power cord. 3. Make sure the Power LED turns into a solid light for AP configuration. 802.3af – Compliant PoE Switch PoE LAN PoE Injector
Quick Setup Guide 9 Altai Technologies Ltd. All rights reserved 1. Change TCP/IP Setting on Your Computer For Windows 7/8/10 users, 1. Go to Control Panel, click Network and Sharing Center and then choose the adapter that you want to connect to CX200 unit. In this example, adapter “Local Area Connection” is in connection with CX200. Click it and then click Properties. 2. Under the Networking tab, click Internet Protocol Version 4 (TCP/IPv4) in the list box “This connection uses the following items”, and then click Properties. 3. Type in the following IP address and Subnet mask:  IP address: 192.168.1.2  Subnet mask: 255.255.255.0 4. Click OK to close the Internet Protocol Version 4 (TCP/IPv4) Properties dialog box and click OK again to close the Local Area Connection Properties dialog box.
Quick Setup Guide 10 Altai Technologies Ltd. All rights reserved 2. Access to Web Interface 1. Open a web browser. Type 192.168.1.222 in the address bar and then hit Enter. 2. Login page will come up and you are required to enter username and password. By default, the credentials are:  Username: admin  Password: admin 3. Click Login.
Quick Setup Guide 11 Altai Technologies Ltd. All rights reserved 3. Configure AP Mode (2.4G/5G) Network Scenario Go to Configuration > Wireless > Radio0(2.4G)/Radio1(5G) > General. Below screenshots show an example for 2.4G radio configuration only. Same procedures can be applied to 5G radio configuration. 1. Make sure the box of Enable Radio is checked. Select AP mode for the field of Radio Mode. Then click Submit. 2. Click WLAN and click More… in Detail of WLAN 0 to go to another page for SSID and security configuration. ISP Gateway/Router Modem CX200 (AP Mode) Internet 2.4G + 5G Coverage Modem Ethernet Ethernet Cable Cable Cable
Quick Setup Guide 12 Altai Technologies Ltd. All rights reserved 3. Make sure WLAN is enabled by checking the box. Type in SSID to name the wireless network you want to broadcast and then click Submit. 4. Click the tab WLAN Security. Select WPA2-PSK from the drop down menu of Authentication Mode and select AES for Cipher Mode. Type in a password within 8~64 characters or numbers in Pass Phrase and click Submit. 5. Click Save & Apply at the top right corner to have all changes take effect. 6. Hook up the CX200 as shown in Network Scenario. The SSID should now be broadcast from CX200 and can be seen in the computer for wireless connection.
Quick Setup Guide 13 Altai Technologies Ltd. All rights reserved 4. Connect with Cloud-Based Controller – AltaiCare Network Scenario: 1. You can manage your CX200 and set up hotspot service for the subscribers with AltaiCare, which is a cloud-based system. 2. Go to Configuration > Network > General. Select Switch Mode for Network Setting and make sure the CX200 can reach Internet and communicate with AltaiCare by inputting valid IP settings either via DHCP or with Static IP configuration. Google Public DNS Server can be considered, e.g. 8.8.8.8 or 8.8.4.4 if you are not sure about the ISP DNS’s Server IP. ISP Modem CX200_1 (AP) Local Gateway/ Router CX200_2 (AP)
Quick Setup Guide 14 Altai Technologies Ltd. All rights reserved 3. Click Remote Mgmt and check the box of Enable Remote Management. Select AltaiCare as Management Type and Cloud as Connection Type. 4. Select Full Management if the device is running in AP Mode. For Station Mode, Bridge Mode and Repeater Mode, select Monitor Mode instead. 5. Click Submit and then Save & Apply at the top right corner to make all the changes take effect. 6. Follow AltaiCare Quick Start Guide and register the CX200 in the system for AP management and user service and admission control. 7. CX200 will appear as online in AltaiCare AP list if the connection is successful.
Quick Setup Guide 15 Altai Technologies Ltd. All rights reserved Federal Communication Commission Interference Statement (FCC) – USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. External antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited. 4. Installation procedure Please refer to user’s manual for the detail. 5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. European Conformity (CE) – EU This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. 16 Quick Setup Guide Altai Technologies Ltd. All rights reserved
Quick Setup Guide Warning Only use the power adaptor supplied with CX200. Using a different power adaptor might damage the device. Disclaimer All specifications are subject to change without prior notice. Altai Technologies assumes no responsibilities for any inaccuracies in this document or for any obligation to update information in this document. This document is provided for information purposes only. Altai Technologies reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Copyright © 2018 Altai Technologies Limited ALL RIGHTS RESERVED. Altai Technologies Limited Unit 209, 2/F, Lakeside 2, 10 Science Park West Avenue, Hong Kong Science Park, Shatin, New Territories, Hong Kong Telephone: +852 3758 6000 Fax: +852 2607 4021 Web: www.altaitechnologies.com Customer Support Centre: Email: support@altaitechnologies.com 17 Altai Technologies Ltd. All rights reserved

Navigation menu