Altacogni MDH3-1620 Presence Mini(MDH3-1620) User Manual

Yanzi Networks AB Presence Mini(MDH3-1620)

User manual

Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 1 of 42 Installation Manual – Smart Office This installation manual describes how to install Yanzi IoT infrastructure and sensors in offices. IMPORTANT: This manual contains important safety, usage, and service information. We strongly urge you to read this manual in its entirety before using the products.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 2 of 42 Table of Contents Disclaimer .......................................................................................................................................................... 4 1. Introduction ............................................................................................................................................... 5 1.1 Best Technology .............................................................................................................................. 5 1.2 Easiest to install ............................................................................................................................... 5 1.3 Enterprise security ........................................................................................................................... 5 1.4 Cirrus Software as a Service ......................................................................................................... 5 2. Installation Planning ................................................................................................................................ 6 2.1 Infrastructure .................................................................................................................................... 6 2.1.1 Connecting the Gateway to Internet .................................................................................... 6 2.1.2 Building the IoT Network ........................................................................................................ 6 2.1.3 Infrastructure Examples......................................................................................................... 6 2.2 Use Cases ......................................................................................................................................... 9 2.2.1 Space Utilization ...................................................................................................................... 9 2.2.2 Comfortability .......................................................................................................................... 9 2.3 Installation Tool ............................................................................................................................. 10 2.4 Privacy ............................................................................................................................................. 10 3. Installation of Infrastructure ................................................................................................................ 11 3.1 Yanzi IoT Gateway overview and installation ........................................................................... 12 3.2 Gateway Functions ........................................................................................................................ 13 3.3 Gateway LED Behavior ................................................................................................................. 14 4. Teams and Equipment .......................................................................................................................... 15 5. Sensor Handling Tips ............................................................................................................................ 16 5.1 Battery lid ........................................................................................................................................ 16 5.2 Sensor element .............................................................................................................................. 16 5.3 Battery insertion ............................................................................................................................. 16 5.4 External power input ..................................................................................................................... 16 5.5 Sensor buttons and switches ...................................................................................................... 17 6. Placement of Sensors ........................................................................................................................... 18 7. Installation of Sensors .......................................................................................................................... 19 7.1 Start Yanzi Installation tool .......................................................................................................... 19 7.2 Installation Procedure ................................................................................................................... 19 7.3 Yanzi Footfall Camera Overview and Installation .................................................................... 20 8. Wireless Communication ..................................................................................................................... 22 9. SIM card management ......................................................................................................................... 23 9.1 SIM card requirements for Yanzi IoT Gateway 3G .................................................................. 23 9.1.1 SIM requirements .................................................................................................................. 23
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 3 of 42 9.1.2 Operator requirements ......................................................................................................... 23 9.2 Mobile Broadband Coverage ....................................................................................................... 23 9.3 Replacing SIM card in IoT Gateway 3G ..................................................................................... 25 9.4 IoT Gateway 3G SIM card configuration ................................................................................... 27 10. Working with Sensors ........................................................................................................................... 28 10.1 LED Behavior .................................................................................................................................. 28 10.2 Resetting a device ......................................................................................................................... 28 11. Battery Requirements ........................................................................................................................... 29 11.1 Battery Consumption .................................................................................................................... 30 11.2 Note on Lithium Batteries ............................................................................................................ 30 12. Troubleshooting ..................................................................................................................................... 31 13. Security .................................................................................................................................................... 32 13.1 Secure from Node to Cloud ......................................................................................................... 32 13.2 High Security Cloud Model .......................................................................................................... 33 14. IEEE 802.15.4 Overview ........................................................................................................................ 34 15. Privacy Note Examples ......................................................................................................................... 35 15.1 E-Mail Example ............................................................................................................................... 36 15.2 Desk Note Example ....................................................................................................................... 36 16. Disposal and Recycling Information .................................................................................................. 37 17. General Product Information ............................................................................................................... 38 18. Regulatory Information ......................................................................................................................... 40 18.1 Yanzi Motion+ ................................................................................................................................ 40 18.2 Yanzi Comfort ................................................................................................................................ 40 18.3 Yanzi IoT Gateway 2 ..................................................................................................................... 41 18.4 Yanzi Presence Mini ...................................................................................................................... 41 18.5 Yanzi IoT Hybrid Mesh .................................................................................................................. 42
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 4 of 42 Disclaimer Information in this document is provided in connection with Yanzi products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Yanzi’s Terms of Service and other sales conditions for such products, Yanzi assumes no liability whatsoever, and Yanzi disclaims any express or implied warranty, relating to sale and/or use of the Yanzi products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Products from Yanzi must be used only for smart office applications as recommended by Yanzi and are not designed, intended or authorized for use for critical applications, including, but not limited to, life support, health and safety, aviation, nuclear, and security applications or for any other application in which the failure of the Yanzi product could create a situation where personal injury or death may occur. Yanzi may make changes to product(s) and/or the service described in this manual, specifications and product descriptions at any time, without notice. Using your Yanzi products safely • Follow the battery requirements in section 11 before installing any batteries. • Never force a connector into a port. If the connector and port don’t join with reasonable ease, they probably don’t match. Make sure that the connector matches the port and that you have positioned the connector correctly in relation to the port. • Protect your Yanzi products from direct sunlight • Keep away the Yanzi products from sources of liquid, e.g. drinks, bathtubs, washbasins, shower stalls and so on. • Use Yanzi products in environments according to specification. Most products are targeted for indoor office use only. • Only use Yanzi provided power supplies for products requiring external power. • There are no user-serviceable parts inside Yanzi products. For service personnel: Always unplug external power supply, remove batteries, and turn off UPS battery before service operation. About handling Your Yanzi products may be damaged by improper storage or handling. Take caution not to drop them during transport and installation. The passive infrared sensor elements (PIR) (used in e.g. Yanzi Motion, Yanzi Motion+, Yanzi Presence, and Yanzi Presence Mini) are particularly sensitive to external force, so handle them with extra care. WARNING: Do not attempt to open or disassemble any Yanzi products. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 5 of 42 1. Introduction Yanzi Networks delivers an end-to-end, horizontal, and all-IP software Internet of Things platform. We offer sensors, gateways, and Cirrus, a cloud platform solution packaged into a Software as a Service solution (SaaS) for Smart Building applications. The horizontal and all-IP approach provides a solution that is fast, robust, and transformative. 1.1 Best Technology All IP technology, all the way to the sensor, ensures powerful scaling to thousands of sensors and excellent cost efficiency. Yanzi Networks focus on open standards and leverage the widely deployed protocols such as 4G/LTE, Ethernet, Wi-Fi, and the low power "brother" to Wi-Fi, IEEE 802.15.4, which enables battery operated sensors to last for 10+ years. 1.2 Easiest to install Automatic security provisioning provides best-in-class installation provided by the patent pending zero-touch configuration. Sensor installation do not need professional installers but can leverage the employees on site. The optimized power management deliver very long battery life which secure a minimum of maintenance required once installed. 1.3 Enterprise security Yanzi Networks combines ease of installation and maintenance with enterprise security. It is a highly secure solution with all links in Cloud and to Gateway being authenticated with client and server certificates and all communication is made using SSL encryption. All local communication, between the sensors and the Gateway, is encrypted for both wired and wireless solutions. Each sensor has an individual key and can be revoked remotely. 1.4 Cirrus Software as a Service The Yanzi Cirrus Software as a Service provides Device and Gateway management at a new level. The Cirrus data model allow access to any data originating from any location with a uniform interface without the need to understand the sensor details. A secure Gateway-to-Cloud connector to multiple redundant link servers provides reliable remote access to Gateway. The Cirrus open API is a JSON over web socket API where all operations are authenticated. The API support both subscriptions models as well as request/response.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 6 of 42 2. Installation Planning 2.1 Infrastructure The infrastructure has two parts: The Gateway and the IoT network. The Gateway is the brains of the system and manages all sensors, collects all data, and keeps a communication channel open to the Cloud. The IoT network is required to enable sensors to communicate with the Gateway. The IoT network is completely built on IP communication, same as on the Internet. The IoT network is built using one or more Access Points, just like a WiFi network is built. The Access Points communicate with the Gateway using standard Ethernet connectivity. For more information on networks and wireless technologies, please see support sections below. Before ordering any infrastructure products, the first step is to decide type of Internet connection and way to build the IoT network according to the following sections. 2.1.1 Connecting the Gateway to Internet Gateways can be connected to the Internet in two ways: 1) Sharing the Internet connection already available in the building or 2) Using a mobile broadband uplink Sharing the Internet connection does not mean the IoT network must run on the corporate network. It means using a separate port on the customer’ firewall to create a separate network that only provides Internet access. 2.1.2 Building the IoT Network The IoT Network can be built in two ways. 1) If there are Ethernet cabling available in the building, it may be possible to use a single Gateway and connect that to one or more Access Points using those Ethernet cables. 2) If there are no Ethernet cabling available and it is not possible to pull new cables, the IoT network is built using one or more Gateways connecting to the cloud over mobile broadband. Most of the Gateways have access points capabilities already built-in so a small IoT network can be created around each Gateway. These Gateways all communicate separately with the Cloud. 2.1.3 Infrastructure Examples Small system where only one Gateway is enough to create the wireless IoT network. Internet connectivity can be provided using Ethernet (on the left) or using built-in mobile broadband in the Gateway (on the right).
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 7 of 42 Large system reusing Ethernet infrastructure in building and where Internet connectivity can be provided by sharing a port on the existing firewall or using an external mobile broadband router. • Gateway and Access Points needs a network with a DHCP server to get IP addresses assigned. • The Gateway communicates with the Access Points using UPnP and SSL over Ethernet • Internet connection only requires outgoing port 443 and 4445. No inwards connection required. Gateway connects automatically to the Yanzi server. • All communication links are encrypted Yanzi IoT GatewayCustomer Firewall orMobile Broadband Router3G/4G/LTEPartnerCloud ServersYanzi SensorsYanzi IoT Gateway 4G3G/4G/LTEPartnerCloud ServersYanzi SensorsYanzi IoT GatewayCloud ServersSecure Cirrus APIIPv6 over IEEE 802.15.4handled by the GatewayCustomer Firewall orMobile Broadband RouterYanzi IoT Access PointsYanzi SensorsFiber/DSL or 3G/4G/LTEEthernetSwitchPartnerCloud Servers
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 8 of 42 • PoE switch connects and powers all IoT Access Points (when AP has PoE support) • Optional UPS on PoE switch and Gateway to enable operation when power is lost Large system completely stand-alone without using any existing infrastructure. Cloud ServersSecure Cirrus APIIPv6 over IEEE 802.15.4handled by the GatewayYanzi IoT Gateway 3G/4GYanzi Sensors3G/4G/LTEPartnerCloud Servers
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 9 of 42 2.2 Use Cases Depending on which use case to cover, the type and position of sensors may vary. Two typical use cases are shown below for space utilization and comfortability. 2.2.1 Space Utilization For space utilization, Yanzi Motion/Presence sensors are added under the table at each work desk chair and at each chair of larger conference rooms (typically rooms with 6 chairs or more) to detect usage. For room usage, Yanzi Motion/Presence or Yanzi Motion+ is placed on the wall (rooms larger than 20m2 are recommended to use two sensors to make sure the whole room is covered). Selection between Motion/Presence sensor and Motion+ sensor depends on if comfortability use case also should be covered as the Motion+ sensor monitors more things than the Motion/Presence sensor. Motion/Presence sensors may also be used for restroom utilization to monitor each stall as well as the washroom. Footfall cameras may be placed in the ceiling of each entrance to the building and can as well be placed at the entrance to any area where specific information is wanted. The footfall cameras are connected to the Gateway using Ethernet/PoE. This proposal do not focus on footfall cameras. 2.2.2 Comfortability For comfortability, the work environment is monitored using for example CO2, temperature, humidity, barometric pressure, volatile organic compounds (VOC), ambient light and ambient noise sensors. Yanzi Comfort sensors are placed in each room (conference room, phone booths, locker room, etc.) where people are present for longer periods of time as well spread out in open work spaces. In open work spaces, recommendation is to use one Yanzi Comfort for each 15-25 work desks. Yanzi Motion+ are used to monitor occupancy and light at work desks (preferably placed in the ceiling where it covers about 6-8 work desks depending on height of ceiling). It is also used to monitor utilization of smaller rooms such as conference rooms, phone booths, locker rooms, storage rooms, kitchens, restrooms, etc. PFCPPPPPPPPPPPPPPPPPPPPPPPFCP PPPPPWork Desks/Hot DesksConference/Phone Rooms Restrooms Dining AreaFC Ceiling mount camera for footfall applicationsYanzi Footfall CameraPOptimized for space Utilization. PIR motion.Yanzi Motion/Presence
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 10 of 42 2.3 Installation Tool One of the important parts after the installation is to know where sensors have been placed. The mapping between the sensor unique ID and the physical location is done at time of installation using the Yanzi installation tool in Yanzi Live. This is a browser based installation tool that allows for quick installation of many sensors. Prior to installation, make sure the floor map(s) has been provided to Yanzi and added to your account. 2.4 Privacy It is strongly recommended to inform personnel of the reasons for the installation, that their privacy is respected and maintained at all times, and clarify that no images, video, or sound is ever recorded. The correct process for this is up to each company to decide but Yanzi recommends the following as a basis: 1. Send an email with information two weeks prior to installation 2. Leave a note on each person’s desk at the time of installation 3. Send an email again after installation is done reminding why this is done See section 15 for examples of wording. AMMMA A AAMAM MMMMAA AAMMMMMMotion, Temperature, Humidity, Ambient Light, Ambient Noise (Sampled)Yanzi Motion+Work Desks/Hot DesksConference/Phone Rooms Restrooms Dining AreaCO2, VOC, Temperature, Humidity, Air Pressure, Ambient Noise (Continuous)AYanzi Comfort
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 11 of 42 3. Installation of Infrastructure Gateways are recommended to be registered prior to installation. Register means connecting the Gateway to a specific account. Users can then be added or removed from this account to control access. Registration is done using the installation tool or provided as remote support by Yanzi. Yanzi needs the Gateway ID (printed on the Gateway label), the location name it should have, as well as a user with administrative rights for this account. Make sure the infrastructure is always built prior to installing any sensors. Install the Gateway and connect it to Internet. Install the Access Points and connect them to the same network as the Gateway according to the pictures above. The wireless IoT network created around Access Points have a range of about 500-1,500 m2 (~ 5,000-15,000ft2). The actual range depends heavily on walls, obstacles, materials, and number of potential mesh nodes (This is very similar to WiFi access points). Wireless coverage is affected for example by elevator shafts (lots of metal), bathrooms (water and thick walls), and other radio disturbances such as WiFi access points and microwave ovens. IoT Access Points (or Gateways with mobile broadband) is shown below with an approximated wireless coverage shown as orange circles. In this specific building, two Access Points per floor is enough. AP AP
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 12 of 42 3.1 Yanzi IoT Gateway overview and installation The following applies to all variants of Yanzi IoT Gateway (DR2-88xx) and Yanzi IoT Gateway Plus (DR2-89xx). For more details on gateway LED behavior, see section 3.3. Installing and registering a gateway 1. Insert the included power adapter to a power outlet and plug in the cable to the gateway. The power LED should now turn solid green. 2. Optional: Enable the gateways built in UPS by pushing the switch located on the left side of the gateway towards the grey sleeve (Applies to Yanzi Gateway and Yanzi Gateway Plus). 3. Connect the gateway to internet a. For Ethernet based gateway: Connect an Ethernet cable to the gateways Ethernet port. Connect the cables other end to an available switch/router port with internet access. b. For 3G based gateways: Once the gateway has booted, it will search for a cellular network, please allow up to 10 minutes for this to complete. 4. Once step 3 is complete and the gateway has established a connection to the Yanzi cloud, the status LED should blink green. 5. Register the gateway – follow the below steps; a. Use Googles Chrome browser, go to the link specified by Yanzi, typically something like https://cirrus.yanzi.se b. Sign in using the credentials provided by Yanzi, email and password c. In the upper right hand corner (below the search field) you will find a “+Install Gateway” button. Click this and enter the details in the ‘Connect New Gateway’ field i. Gateway ID: Fill in your gateways ID, located on the silver label on the gateway ii. Location Name: Fill in the name of your Location, e.g. “Yanzi HQ”. iii. Account: Select an account to link this Location to and click register 6. Once the registration process is complete, the status LED will turn solid green.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 13 of 42 3.2 Gateway Functions Port Desription Power Port Only use Yanzi Wall Adapter according to Gateway datasheet, typically 12V/2A. Ethernet Port 1x 10/100 Ethernet port (DR2-88xx) 2x 10/100 Ethernet ports (DR2-89xx) UPS Switch Enables/disables built-in battery backup. Push to front to disable. Push towards rear to enable. Power/Status LED Indicates power status according to section 3.3. USB Port Reserved. Do not use.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 14 of 42 3.3 Gateway LED Behavior Yanzi IoT Gateway and IoT Gateway Plus both have a dual color LED that can indicate green or orange. The typical LED behaviors are shown in the table below. Gateway LED State Yanzi IoT Gateway Yanzi IoT Gateway Plus Top LED (Power) Off Power is off Power is off Steady green Power applied and gateway is turned on Power applied and gateway is turned on Steady orange N/A External power failure, the gateway is operating on the built-in battery Bottom LED (Status) Off Status LED is off whenever the gateway is off and during boot Status LED is off whenever the gateway is off and during boot Blinking green Gateway is ready to be registered in the portal Gateway is ready to be registered in the portal Steady green Gateway is connected to portal Gateway is connected to portal Steady orange Gateway has local access but is not connected to the portal Gateway has local access but is not connected to the portal Blinking orange* *Applies to 4G/3G gateways Mobile broadband connection error This could for example indicate that all the monthly data has been used Mobile broadband connection error This could for example indicate that all the monthly data has been used
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 15 of 42 4. Teams and Equipment Most efficient is usually to have installer teams of 2-3 persons. Multiple teams can work in parallel for quicker sensor installations. 1 person places the sensor on the floor map and scans the QR code. 1-2 persons place the sensor on the correct spot in the building. Each installation team needs • Laptop with Chrome browser o Internet access is required for the laptop as installation tool is web based • QR code scanner o Such as the Motorola, Symbol, or Zebra DS6708 • Plastic bins for carrying sensors • Access to all rooms in building where sensors are to be placed
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 16 of 42 5. Sensor Handling Tips 5.1 Battery lid To open and close the battery lid, gently push the back side label close to the battery lid with your thumb and slide the battery lid downwards with your other hand. 5.2 Sensor element The sensor elements must be handled with care as these are sensitive parts. 5.3 Battery insertion The battery powered sensors operate with 2 or 4 batteries. Two batteries makes the product run for half the time which is usually 5 years. When using two batteries, please use the bottom two battery slots as shown in section 11. Note the polarity when inserting the batteries. Polarity is always shown in the sensors battery compartment as well as on the battery itself. It is very important to follow the battery requirements when inserting batteries, see section 11 for more details. Verify that the front panel LED is turned on within 5 seconds after inserting batteries. Note that it may only be turned on for a very short while to save battery. If you do not see the LED come on even for a short while, please remove the batteries and re-insert them again. If it still doesn’t work, please see the Troubleshooting section. 5.4 External power input For sensor requiring an external power supply, insert the USB-C connector on the bottom side of the sensor carefully until a “click” is detected. See each product manual for more details. Verify that the front panel LED is turned on within 5 seconds after inserting power.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 17 of 42 5.5 Sensor buttons and switches All Yanzi sensors have a status button, a short press on the status button will indicate the status using the LED, see 9.1 for LED behavior. Some sensors ship with batteries already inserted and therefore have a power switch. Carefully push the switch to its upper position to turn on the sensor. Should you want to turn off the sensor, carefully push the switch to its downward position. Use a sharp tool such as a paper clip or mobile phone SIM card ejector to flip the switch. Yanzi Motion+ shown as example above
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 18 of 42 6. Placement of Sensors General tips on placement • Try to place the sensors in discrete locations • Place sensors along walls at about 150-170 cm (60-70 inches) from floor • Sensors are attached using adhesive tape • Target wood, plastic, or metal surfaces that are flat • Avoid wall papers as they may break if sensor must be removed • Avoid painted walls when using adhesive tape as modern paint is efficient in repelling adhesive tape • Dry target surface with a cloth to remove dust, dirt, and grease • Remove tape cover and press firmly ON THE SLEEVE for 10 seconds. After 10 seconds, the adhesive tape is strong enough to hold the sensor. Full adhesiveness is reached after 72 hours. Yanzi Motion+ • Place on wall of smaller rooms such as conference rooms and phone booths • Place in ceiling above groups of 4-8 work desks Yanzi Comfort • Place on wall not close to work desk • Place vertically with the power connecter facing downwards • Avoid placement near any air ventilation inlets or outlets as this may cause inaccurate readings • Requires a power outlet within 0.5 meters (longer cables available as accessory) Yanzi Presence for work desks • Place under work desk about an arm’s length from edge Yanzi Presence for conference room chairs • Place under conference room table at each chair about an arms length from edge Yanzi Presence for conference room corner • Place in corner of smaller rooms and along walls in larger rooms • Face away from windows to avoid direct sunlight • Face away from door to avoid detecting people walking outside the room • Use multiple sensors for large rooms (>20m2)
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 19 of 42 7. Installation of Sensors Sensors are installed using the Yanzi installation tool. Make sure you get login credentials from Yanzi prior to installation and that the floorplan of the building has been added to the account. 7.1 Start Yanzi Installation tool 1) Using a Chrome browser, go to the link specified by Yanzi, typically something like https://cirrus.yanzi.se 2) Sign in using the credentials provided by Yanzi, email and password 3) When logged in, click “Locations” in the left column 4) In the list of locations, click on the location where installation should take place. 5) Click “Installer” to the right of the top bar 6) The floor plan will now open and you are ready to install sensors The Yanzi installation tool is a cloud based tool so make sure Internet connection is available throughout the building. 7.2 Installation Procedure 1) Select floor in the bottom left corner of the map 2) Zoom into area on the floorplan where the sensor should be installed 3) Click on the exact location where the sensor will be installed 4) Add the following properties in the “Add new device” list DID. Scan the sensor QR code using the hand scanner. Example: EUI64-0090DAFFFE00526A Optional: Logical Name Example: Entrance motion detector Optional: Room name Example: Oval office 5) Click “Connect” in bottom right corner 6) Turn on the sensor • For battery powered sensors: Push power switch to ON (see section 5.5) or insert batteries. • For USB powered sensors: Insert the USB cable and plug in the power adapter to a wall socket. 7) Verify the LED on the front panel is lit within 10 seconds. If the LED has not made any indication within 10 seconds, check batteries or external power. 8) Dry target surface with a cloth to remove dust, dirt, and grease 9) Place sensor by removing the non-stick film on the back of the sensors sleeve and place it into position by pressing FIRMLY on the gray sleeve for 10 seconds (if adhesive tape is used) 10) Restart at point 3 for next sensor When done, leave the Installer and go to the List view to verify that all your added sensors are connected. Sensors are assigned a radio channel, encryption key, and configuration settings automatically and data should be available in the Cloud within a few minutes after installation.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 20 of 42 7.3 Yanzi Footfall Camera Overview and Installation General requirements The Yanzi footfall camera must: • Be mounted with the correct orientation • Be in an area where, preferably, people do not stagnate • Be in a place with adequate illumination • Be outside of the door opening area Depending on the ceiling height, the width the camera will be able to count varies as shown in the illustration and in the chart below. The footfall camera must be correctly aligned and oriented as shown below. Height (A) Width (B) 2.5m 2.5m 3.0m 3.5m 4.0m 5.5m 5.0m 7.0m 6.0m 9.0m 7.0m 11m 8.0m 12m
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 21 of 42 Ensure that the door won’t open directly under the cameras counting line. Installation and configuration 1. Mount the camera in the ceiling, having considered the requirements listed above. Make sure you connect the camera using an PoE switch as it gets power over Ethernet. Please note that the footfall camera must be connected to the same network as the Yanzi Gateway 2. Log in to the footfall camera by typing in its assigned IP-address in your internet browser of choice. The default login credentials - username: admin and password: admin 3. When logged in, click Wizard and follow the steps to configure the footfall camera. 4. Once the footfall camera is mounted and configured you need to connect the footfall camera to you Yanzi Location, to do this: a. Go to the Cirrus link specified by Yanzi, typically something like https://cirrus.yanzi.se b. Sign in using the credentials provided by Yanzi, email and password c. In the list of Locations, select the Location where you mounted the footfall camera and click Installer d. In the dropdown menu called ‘Discovered Things’ you will now be able to see your recently installed footfall camera. Click Quick Connect e. Your Yanzi Footfall Camera is now connected and will start pushing data to the cloud
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 22 of 42 8. Wireless Communication Yanzi sensors operate on world-wide standard physical medias only such as IEEE 802.3 (Ethernet) and IEEE 802.11 (WiFi) for high performance sensors, and IEEE 802.15.4 for very low power sensors. The wireless protocols are all designed by IEEE to operate simultaneously with minimum interference. Yanzi uses very low power for IEEE 802.15.4 sensors in order to be friendly with WiFi. An advanced back-off/retransmission scheme ensures good coexistence with Wifi networks as well as providing minimal impact from unwanted interference. IEEE 802.15.4 has similar range to WiFi and normally operates on the same ISM band, 2.4GHz. There are Sub-GHz solutions for IEEE 802.15.4 as well but for normal high density installations, it is not required for reach. For more details on IEEE 802.15.4, please see section 14. Sensors communicate periodically (typically every minute but depends on type of sensor) with the Gateway. Events are communicated immediately (and not periodically) for fast notifications. All communication is full duplex ensuring that all packets are received properly.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 23 of 42 9. SIM card management Yanzi Gateways with mobile broadband are shipped without SIM card inserted. This section describes the requirement for the SIM card as well as instructions on how to add a SIM card and configure the Gateway accordingly. For details on pre-supported operators and countries, please see section 15. 9.1 SIM card requirements for Yanzi IoT Gateway 3G 9.1.1 SIM requirements Item Requirement Note Bandwidth Minimum HSPA HSPA is up to 5.76 Mbit/s Data amount 5 – 20 GB/month Data usage heavily depends on the implementation of the analytics, front end, and end usage. For many installations, 5GB/month works well but Yanzi strongly recommends 20GB/month. Over-usage of data - Strongly recommended that operator does not incur extra charges for over-usage of data. Customer will be responsible for any extra charges. PIN No Pin code must be disabled APN Standard APN and APN authentication (username/password) APN and APN authentication must be made available to Yanzi at the time of order if Gateway is to ship pre-configured. Size Micro-SIM Management - Web interface with over-usage warning recommended Roaming Sweden Roaming for Sweden must be enabled (without requiring confirmation by the user) with at least 100 MB of data in order to verify APN configuration. 9.1.2 Operator requirements Network frequency: 850/900/1900/2100MHz Network speed: Minimum HSPA 9.2 Mobile Broadband Coverage Good radio coverage is required for the service to work well. Verify prior to installation that the chosen operator has 3G and 4G access in the building where Gateways are to be installed. Note that even if the operator says the area has coverage, it doesn’t mean coverage is available inside the building.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 24 of 42
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 25 of 42 9.3 Replacing SIM card in IoT Gateway 3G Always take extra caution when working with exposed electronics, never touch the internal components or the logic board. 1. Remove the grey Yanzi sleeve 2. Using a Philips screwdriver, unscrew the three screws on the back of the gateway 3. Carefully open the gateway as the top lid holds the battery and is connected to the logic board 4. Carefully push the micro-SIM card out of its holder
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 26 of 42 5. Insert the new micro-SIM card, take note of the SIM card orientation shown below Yanzi IoT Gateway Yanzi IoT Gateway Plus 6. Re-assemble the gateway Please note that you will have to update the gateways SIM card configuration after changing operator. See section 9.4.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 27 of 42 9.4 IoT Gateway 3G SIM card configuration Put files in a folder named yanzi-upgrades on a USB stick and add the three following files as shown in the table below. Please note that the three files must not include a file extension. Filename Description File content Comment wwan Wireless WAN (3G) on/off When the wwan file contains “on” 3G will be enabled and when containing “off” the gateway will be configured for Ethernet use. apn APN config 3g.telia.com Telia APN show as an example, ask your SIM card provider for the correct APN. apn.auth APN Authentication username:password Note that not all operators require an APN authentication, if yours doesn’t, don’t include this file. Once you have put these files on a USB stick, follow the steps below: 1. Ensure gateway is off 2. Insert the USB stick 3. Turn the gateway ON (USB still inserted, let the gateway run for at least 15 mins) 4. Turn the gateway OFF (USB still inserted, make sure gateway is switched off at least 10 seconds) 5. Turn the gateway ON (USB still inserted, let the gateway run until the lower LED turns solid or blinking green) 6. Remove the USB stick 7. Reboot the gateway: Verify the lower LED still turns green (or blinking green)
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 28 of 42 10. Working with Sensors 10.1 LED Behavior All sensors have a dual color LED that can indicate green or orange. The typical LED behaviors are shown in the table below. Sensor LED State Description Note Off Power is off or sensor is in sleep All sensors turn the LED off a short while after power has been applied to avoid light pollution. A short press on the button turns the LED on to display status if sensor has power (see section 5.5) Short orange or green blink Power has just been applied and sensor is booting up Wait a few seconds for actual status Blinking green (slow) Sensor is ready to be peered with a location Use the installation tool to peer the sensor with a Gateway (Location) Steady green Sensor is peered with a location and working Blinking green (fast) Sensor is about to be reset See details on resetting a device in section below Blinking orange/green (fast) Sensor has been reset to factory default See details on resetting a device in section below 10.2 Resetting a device If a device should be removed from an installation, please hold the status button (see section 5.5) on the sensor pressed for about 20 seconds. After 15 seconds the LED will start flashing green quickly to warn that if you keep the button pressed, it will reset. After another 5 seconds it will start flashing orange/green which means it will now reset when the button is released. Release the button and the sensor will reboot as factory default.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 29 of 42 11. Battery Requirements It is very important to follow these guidelines to avoid serious injuries. Bad handling of batteries may cause them to leak, potentially rapidly, creating a risk of injury as the internals of batteries are very corrosive. It is recommended to use Alkaline batteries in most use cases and Lithium (LiFeS2) for cold use cases. • NOTE THE POLARITY OF THE BATTERIES WHEN INSERTING THEM. Polarity is always shown in the battery compartment as well as on the battery itself. The plus side is marked on the picture below. • NOTE THE VOLTAGE OF THE BATTERIES. There are several voltages available for the same size of batteries. See the product manual for details on which battery to use. • ONLY USE NEW BATTERIES. Batteries older than 1 year should be avoided as they may have aged differently and therefore cause harm when used together. • NEVER MIX TYPE OF BATTERIES. Only use the same type of chemical compound in all batteries. • NEVER MIX OLD AND NEW BATTERIES. Make sure all batteries used are from the same package. • IF BATTERIES GET WARM WITHIN 5 SECONDS AFTER INSERTION, REMOVE THE BATTERIES IMMEDIATELY. • IT IS RECOMMENDED TO USE PROTECTIVE GLASSES WHEN WORKING WITH BATTERIES. Note polarity symbols in the battery compartment
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 30 of 42 11.1 Battery Consumption Yanzi sensors are very power efficient. Most battery driven Yanzi sensors consume less than 5uA during sleep which is class leading. Sensors wake up periodically to communicate with the Gateway with a configurable frequency. Sensors detecting motion communicates with the Gateway immediately upon motion for fast response times and goes to sleep for a certain time following a motion, called black-out period, to save battery. Things that affect the battery life is shown below. Battery life time cannot be guaranteed if used outside of below recommendation. Note that default sensor settings may differ from below requirements. Item Required for 5-year battery life Yanzi Presence and Yanzi Climate Battery Type of battery AA, 1.5V Battery chemistry Alkaline or LiFe Number of batteries 4 (Inserted/replaced according to Yanzi battery requirements) Battery capacity Minimum 2,700mAh Usage Radio usage Minimum 70% of 2.4GHz radio channel Maximum background noise floor of -100dBm Radio coverage Minimum RSSI of -80dBm Communication interval 2 minutes or more with 50% blackout period Environment 16-25°C 20%-80% relative humidity PIR usage Maximum 8h per day Peering process Peered within 4 hours Gateway availability >99% 11.2 Note on Lithium Batteries There are several types of Lithium batteries on the market in the standard size called AA. First, care must be taken to make sure the voltage is correct according to the datasheet; 1.5V, 3.0V, or 3.6V. Yanzi has identified that several suppliers of 1.5V Lithium batteries of type LiFeS2 often produce a voltage higher than 1.8V. Voltages above 1.8V may harm products targeted for 1.5V batteries so please verify that the battery you use follows the recommendations in the product datasheet.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 31 of 42 12. Troubleshooting Behavior Solution Note Gateway won't connect Ethernet-based gateways Yanzi IoT Gateway: 1. Ensure Ethernet cable is plugged in 2. Verify gateway is receiving power and is turned on Yanzi IoT Gateway Plus: 1. Ensure Ethernet cable is plugged in to the right-hand port 2. Verify gateway is receiving power and is turned on. If using PoE, double-check your switch is providing power over Ethernet. Yanzi IoT Gateway Rack: 1. Ensure Ethernet cable is plugged into the right-hand port (the one next to the VGA port) 2. Verify the gateway is receiving power and is turned on 3G/4G-based gateways Yanzi IoT Gateway 3G: 1. Verify gateway is receiving power and is turned on 2. Ensure sim card is inserted Yanzi IoT Gateway Plus 3G: 1. Verify gateway is receiving power and is turned on 2. Ensure sim card is inserted Sensor won’t connect Battery powered sensors 1. Ensure batteries are inserted 2. Some battery powered sensors have a power switch, verify this is set to ON USB powered sensors 1. Ensure cable is plugged in 2. Verify the power adapter is plugged in to a working outlet It is always possible to check any sensors status by pushing the button. The LED will then indicate the current state of the sensor, see section 10.1 for LED behavior.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 32 of 42 13. Security Security is one of the most important pillars as distributed IoT devices require high security on all links. This section gives a quick overview of the security models on Gateway to cloud and sensor to Gateway. 13.1 Secure from Node to Cloud SSL encrypted channels from Open Cloud API to Cloud to Gateway authentication by certificate. Automatic security provisioning of devices provides quick installation: • Automatic key management with ECC (Vendor, Owner, and Location keys) • Application layer encryption for user data and management data including firmware updates • Layer 2 key distribution when applicable (Wi-Fi and IEEE 802.15.4) • Individual security keys per device with revoke capability SSL – Client and Server CertificatesHTTPS – Ethernet and WiFiECC – Security setupAES – Application layer encryptionCloud ServersPartnerCloud ServersSSL – Client and Server Certificates
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 33 of 42 13.2 High Security Cloud Model All access to IoT data is authenticated in the API. All links are authenticated with client and server certificates and all communication is made using SSL encryption. Data model • Authentication server (Orange) signs all certificates as well as redirects the Gateways to the correct Link server • Link servers (Light Blue) manage Gateways and pass data to Microsoft IoT Hub via API Server. • API servers (Green) provides a secure interface to analytics partner and acts as an aggregator for multiple link servers. • Prototocl Translators (Dark Blue) translates Yanzi Cirrus API to other APIs such as MQTT. • Local Gateway (Gray) stores all sensor data temporarily to support autonomous operation when Internet connection is down Two Cloud Server models: • Shared: Servers are shared between customers • Dedicated: All data is kept within a specific cloud provider Link ServersAuthentication Server API ServersProtocol TranslatorsCirrus APICustomer SitesMQTTMS IoT HubIBM MessageSightIBM IoT Foundation
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 34 of 42 14. IEEE 802.15.4 Overview IEEE 802.15.4 is a low power wireless network optimized for battery driven devices. On the world-wide approved 2.4GHz spectrum, it supports 16 channels with 250kbps per channel where each channel has a bandwidth of 2MHz. A comparison with WiFi, IEEE 802.11b/g/n, and Bluetooth can be seen on the below picture. IEEE 802.11b uses 11 channels in US and 13 channels in Europe with a bandwidth of 22MHz per channel. Yanzi Gateways automatically select channels for IEEE 802.15.4 that sensors attach to. 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 24722412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 247231 6 11IEEE 802.11n40MHzIEEE 802.11b/g/n20/22MHz11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 262405 2410 2415 2420 2425 2430 2435 2440 2445 2450 2455 2460 2465 2470 2475 2480IEEE 802.15.4World-Wide[MHz][MHz][MHz]2407240224072402 2477 2482112412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 24721Bluetooth[MHz]24072402 2477 248279
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 35 of 42 15. APN The table below shows the pre-configured APN (Access Point Name) settings in the latest Gateway software release. Any SIM/APN settings outside this table must be manually configured according to section 9. If a manual configuration of APN results in a failed connection, the pre-configured APNs will be automatically tested by the Gateway. Below APN settings are applied based on the SIM card IMSI (International Mobile Subscriber Identity) number according to longest prefix match. This list will be updated as more operators are qualified. Country Operator APN Username / Password Network ID Sweden Telia online.telia.se - / - 24001 Tre bredband.tre.se - / - 24002 Tele 2 Internet.tele2.se - / - 24007 Telenor internet.telenor.se - / - 24008 Denmark Telia M2M internet.ts.m2m - / - 23820
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 36 of 42 16. Privacy Note Examples The privacy notes below are only examples and should be modified to work with your company’s privacy policy. 16.1 E-Mail Example 16.2 Desk Note Example This desk is part of our efforts to improve the office experience and increase your comfort. A sensor has been placed under this desk. Note that this sensor only gathers anonymous data and never pictures, video, or sound. For more detailed information, please contact facility management. The following contains some information about the smart sensors we will install throughout the office to help enhance the comfort of our teams. Installing sensors is a step towards our continuous work to improve the office environment experience for all team members. By using these sensors, we can learn more about our office building and work environment, and begin to utilize it fully. The sensors measure parameters such as temperature, humidity, CO2 levels, light levels, motion, and ambient noise. Being aware and able to track and analyze these factors in turn enables us to ensure a great working experience. Your workplace privacy is maintained and no video or sound is recorded at any time If you have any questions regarding this, please do not hesitate to contact the project manager:
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 37 of 42 17. Disposal and Recycling Information This symbol indicates that your product must be disposed of properly according to local laws and regulations. When your product reaches its end of life, contact Yanzi or your local authorities to learn about recycling options.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 38 of 42 18. General Product Information The information below relates to the following products - Yanzi IoT Gateway DR2-8830 - Yanzi IoT Gateway Plus DR2-8910 - Yanzi IoT Gateway 2 DR3-314x - Yanzi Climate SWTH1-1230 - Yanzi Motion MDW1-0201 - Yanzi Presence MDW3-0180 - Yanzi Presence Mini MDH3-1620 - Yanzi Motion+ MDW3-0231 - Yanzi Comfort SWAQ3-0372 These devices comply with part 15 of the FCC Rules / Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 39 of 42 The information below relates to the following product - Yanzi IoT Gateway Plus DR2-8910 For your own safety, and in terms of the RF exposure requirements of the FCC, always observe these precautions: - Always maintain a minimum separation distance of 20 cm (7.8 inches) between yourself and the radiating antenna. - Do not co-locate the antenna with any other transmitting device.
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 40 of 42 19. Regulatory Information This section shows the regulatory information for each product and country that is not available on the product label. 19.1 Yanzi Motion+ The below information relates to Yanzi Motion+, MDW3-0231. Country Standard Regulatory Information China SRRC CMIIT ID: xxxxxxxxxx Japan MIC XXX-ABCDEF Mexico IFETEL IFT: xxxxxxxxxx Singapore iDA 19.2 Yanzi Comfort The below information relates to Yanzi Comfort, SWAQ3-0372. Country Standard Regulatory Information China SRRC CMIIT ID: xxxxxxxxxx Japan MIC XXX-ABCDEF Mexico IFETEL IFT: xxxxxxxxxx Singapore iDA Complies with IMDA Standards DBxxxxxx Complies with IMDA Standards DBxxxxxx
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 41 of 42 19.3 Yanzi IoT Gateway 2 The below information relates to Yanzi IoT Gateway 2, DR3-314x. Country Standard Regulatory Information China SRRC CMIIT ID: xxxxxxxxxx Japan MIC XXX-ABCDEF Mexico IFETEL IFT: xxxxxxxxxx Singapore iDA 19.4 Yanzi Presence Mini The below information relates to Yanzi Presence Mini, MDH3-1620. Country Standard Regulatory Information China SRRC CMIIT ID: xxxxxxxxxx Japan MIC XXX-ABCDEF Mexico IFETEL IFT: xxxxxxxxxx Singapore iDA Complies with IMDA Standards DBxxxxxx Complies with IMDA Standards DBxxxxxx
Doc No: 890-03084 Date: 2017-11-21 Rev 24pa3 Yanzi Networks Installation Manual – Smart Office 42 of 42 19.5 Yanzi IoT Hybrid Mesh The below information relates to Yanzi IoT Hybrid Mesh, IoT-U42. Country Standard Regulatory Information China SRRC CMIIT ID: xxxxxxxxxx Japan MIC XXX-ABCDEF Mexico IFETEL IFT: xxxxxxxxxx Singapore iDA Complies with IMDA Standards DBxxxxxx

Navigation menu