Alcatel USA 8702-50 MDR-8000 User Manual MDR 8000 Radio Family Users Manual Issue 9

Alcatel USA Marketing, Inc. MDR-8000 MDR 8000 Radio Family Users Manual Issue 9

Contents

User manual 03

MDR-8000Alcatel Part Number 3EM11931AA3400 West Plano ParkwayPlano, Texas 75075-5813 U.S.A.Issue 9, December, 2007Microwave Digital RadiosUsers Manual
NORTH AMERICA CUSTOMER SERVICE CENTER24 HOURS PER DAY, 7 DAYS PER WEEKPHONE the Call Center at888-252-2832 (US and Canada)or613-784-6100 (International)ALCATEL-LUCENT’S PRIMARY MISSION ISSATISFYING OUR CUSTOMERS' QUALITY EXPECTATIONS.The Call Center Agent (CSA)Will help connect you with Technical Assistance (TAC)Or assist you with a Repair and Return• Phone-based technical support• After-hour emergencies•  On-site technical support• E-mail support ml-tac.support@alcatel-lucent.com•  Software and hardware upgradesTAC• Module repairRepair and Return•  Training http://www.alcatel-lucent.com>support – Technical TrainingOther Services Offered•  Field Services  –  Installation and test•  Customized and Comprehensive Service Agreements• Registration http://www.alcatel-lucent.com>MyAccess – Once registered    –  From “MyAlcatel” go to “Alcatel Support Documentation”  – Register for access to Documentation and e-mail Update notifications       For Product Change Notices (PCN), Product Documentations, etc. – Software and Hardware upgrade documentation
Telephone Assistance, Normal Working Hours (CST 8am 5pm M-F)TAC supports  all Alcatel North America Microwave products. This includes routine questions and emergency service.  Telephone Assistance, Emergency After-Hours•  Defined as loss of traffic, standby equipment, or network visibility on traffic-bearing systems.•  Available through our Customer Service Agents (CSA). Contact Information Ask the Customer Service Agent (CSA) for a Microwave (MW) or a Network Management Service engineer (NMS).Please provide the following information to the Customer Service Agent (CSA):•  Last and First name• Company name• Telephone number•  City and state (Street address if applicable) or Site Name and Location• Equipment type•  A  brief  description of the problem affecting their equipment•  Customer Priority: High, Medium, or Low.•  TL-9000 Severity as described below.Creating a TAC Action Request (AR)CriticalTL-9000 Severities DefinedMajorMinor  Problems not classified as critical or major.Problems severely affecting service, traffic, capacity, or network management. They require immediate corrective action. (Ex. Loss of network management capability, loss of traffic imminent or existing). Conditions seriously affecting system operation. They require immediate attention. (Ex. processor outage, loss of standby equipment, loss of remote access, or network managers).TACTechnical Assistance Center
   T able of Contents TOC   -   1 Page Section 1 General 1.1 INTRODUCTION ............................................................................................. 1   -   1 1.2 CONTENT ....................................................................................................... 1   -   1 Section 2 Operation 2.1 GENERAL ........................................................................................................ 2   -   1 2.2 TURN-ON ........................................................................................................ 2   -   1 2.3 USER SYSTEM INTERFACE (USI) PROVISIONING FUNCTION/OPERATION ...... 2   -   2 2.4 OPERATING PROCEDURES .............................................................................. 2   -   2 2.4.1 Radio Receiver Manual Switching ..................................................................... 2   -   2 2.4.2 Radio Transmitter Manual Switching ................................................................. 2   -   5 2.4.3 Radio I/O Interface Manual Switching .............................................................. 2   -   5 2.4.4 MCS-11 Operation .......................................................................................... 2   -   7 2.4.5 Lamp Tests ....................................................................................................... 2   -   8 2.4.6 Alarm Checks .................................................................................................. 2   -   8 2.4.7 Orderwire Operation ....................................................................................... 2   -   8 2.4.8 Initiating Outgoing Orderwire Calls .................................................................. 2   -   8 2.4.9 Answering Incoming Orderwire Calls ................................................................ 2   -   8 2.5 TURN-OFF PROCEDURE ................................................................................... 2   -   9 2.6 EMERGENCY OPERATION .............................................................................. 2   -   9 2.7 MODEM OPERATION ...................................................................................... 2   -   9 2.8 CONTROLS, INDICATORS, TEST POINTS, AND CONNECTORS ....................... 2   -   9 Section 3 Interconnect 3.1 SECTION INTRODUCTION .............................................................................. 3   -   1 3.2 POWER CABLE CONNECTION ....................................................................... 3   -   1 3.3 PDU STRAPPING AND CONNECTIONS ........................................................... 3   -   4 3.4 SHELF/RACK ALARM CONNECTION .............................................................. 3   -   5
 Page TOC   -   2 3.5 MDR-8000 SYNCHRONOUS REPEATER CONNECTIONS ................................ 3   -   5 3.5.1 Low Capacity DS1 Radios ................................................................................ 3   -   7 3.5.2 High Capacity DS3 Radios ...............................................................................3  -  73.5.3High Capacity OC3 Radios..............................................................................3  -  73.5.4MDR-8000 Synchronous Repeater Compatibility Matrix.....................................3  -  83.5.5MDR-8000 Synchronous Repeater Cables.........................................................3  -  83.6DS1 CONNECTIONS (J303 IN AND J304 OUT)..............................................3  -  93.7DS1 REPEATER (J314 ON ONE SHELF TO J314 ON SECOND SHELF)............3  -  113.8DS3 LBO STRAPPING AND CONNECTIONS.................................................3  -  123.9DS3 LBO DS3 BNC CONNECTIONS (J21 THROUGH J26).............................3  -  133.10DS3 LBO WAYSIDE DS1 CONNECTIONS (J201 IN AND J202 OUT).............3  -  143.10.1Wayside DS1 Terminal..................................................................................3  -  143.10.2Wayside DS1 Repeater..................................................................................3  -  143.11DS3 REPEATER (J401 ON ONE SHELF TO J401 ON SECOND SHELF)............3  -  163.12FIBER OPTIC CABLE CONNECTIONS.............................................................3  -  183.12.12 or 4 Fiber Management Panel.....................................................................3  -  193.12.22x4 Fiber Switched Management Panel..........................................................3  -  193.13OC3/STM-1 AUX INTERFACE BOARD WAYSIDE DS1 CONNECTIONS  (J201 IN AND J202 OUT)..............................................................................3  -  223.13.1Wayside DS1 Terminal..................................................................................3  -  223.13.2Wayside DS1 Repeater..................................................................................3  -  223.14 OC3/STM-1 REPEATER  (J203 ON ONE SHELF TO J203 ON SECOND SHELF)...................................3  -  233.15ETHERNET CABLE CONNECTIONS...............................................................3  -  243.15.1Automatic MDI/MDI-X Configuration...............................................................3  -  243.15.2Crossover Cable Option.................................................................................3  -  253.15.3Terminal Connections.....................................................................................3  -  293.15.4Repeater Connections....................................................................................3  -  333.16USI/CONTROLLER CABLE CONNECTION TO LAPTOP (J301).........................3  -  353.17SERVICE CHANNEL CONNECTIONS............................................................3  -  373.17.12-Wire Handset Connection...........................................................................3  -  373.17.2Service Channels Provisioning Options............................................................3  -  393.17.3Audio 1, Audio 2 (J316, J317) Connections...................................................3  -  393.17.4RS-232-1, RS-232-2 (J312, J313)....................................................................3  -  43
PageTOC  -  33.18MCS-11 CONNECTIONS..............................................................................3  -  443.18.1MCS-11 Master (J307)...................................................................................3  -  453.18.2MCS-11 Repeater-to-Spur Daisy Chain Connection (J308/J309).......................3  -  483.18.3MCS-11 Spur Connection (J310)....................................................................3  -  563.19TMN CONNECTIONS...................................................................................3  -  583.19.1Installing Module...........................................................................................3  -  583.19.2Typical Interconnect Scenarios........................................................................3  -  603.19.3Front Access Connectors.................................................................................3  -  643.19.4MATING CABLES..........................................................................................3  -  673.19.5Front Panel Craft Interface Connector J5..........................................................3  -  683.20ELMC (J315, J318)........................................................................................3  -  693.21FOREIGN ALARM INTERFACE (J305).............................................................3  -  723.22ALARM, STATUS, AND CONTROLS INTERCONNECT.....................................3  -  753.22.1Controller Bus................................................................................................3  -  773.22.2Control Inputs................................................................................................3  -  773.22.3Station Alarm Inputs/TBOS Interface...............................................................3  -  773.22.4Station Alarm Wiring.....................................................................................3  -  783.22.5Relay Alarm/Status Outputs............................................................................3  -  793.22.6Relay Control Outputs....................................................................................3  -  80Section 4 Initial Turnup4.1SECTION INTRODUCTION..............................................................................4  -  14.2RECOMMENDED SEQUENCE.........................................................................4  -  14.3SECURITY MANAGEMENT..............................................................................4  -  24.4LOAD MDR-8000 SOFTWARE ON PC..............................................................4  -  24.5TURN-ON PROCEDURE...................................................................................4  -  44.6ESTABLISH COM PORT....................................................................................4  -  44.7TEST PROCEDURES..........................................................................................4  -  74.8PROVISIONING RADIO...................................................................................4  -  74.9PROVISION ETHERNET FACILITY....................................................................4  -  294.9.1Auto-Negotiation............................................................................................4  -  304.10PROVISION DS1 FACILITY.............................................................................4  -  32
PageTOC  -  4Section 5 Maintenance5.1INTRODUCTION.............................................................................................5  -  15.2MAINTENANCE PHILOSOPHY.........................................................................5  -  25.3RECOMMENDED TEST EQUIPMENT................................................................5  -  45.4OPTIONAL TEST EQUIPMENT..........................................................................5  -  45.5PERSONAL COMPUTER (PC)/LAPTOP..............................................................5  -  55.6MDR-8000 ALARMS........................................................................................5  -  75.7ALARM MONITORING AND INSPECTION.......................................................5  -  75.8RECOMMENDED PERIODIC CHECKS..............................................................5  -  85.9RADIO TROUBLESHOOTING...........................................................................5  -  85.9.1Troubleshooting USI Alarms..............................................................................5  -  85.9.2Troubleshooting RCVR Lockup Problems............................................................5  -  85.9.3Troubleshooting Performance Screen Errors.......................................................5  -  95.10ETHERNET-SPECIFIC TROUBLESHOOTING......................................................5  -  245.10.1Troubleshooting Using Ethernet I/O Interface Module Front Panel Indicators ......5  -  245.11TMN-SPECIFIC TROUBLESHOOTING..............................................................5  -  265.12MODULE REPLACEMENT...............................................................................5  -  295.13POWER SUPPLY REMOVAL AND REPLACEMENT............................................5  -  325.14CONTROLLER REMOVAL AND REPLACEMENT...............................................5  -  335.15DS3 I/O INTERFACE REMOVAL AND REPLACEMENT.....................................5  -  375.16OC3/STM-1/ETH I/O INTERFACE REMOVAL AND REPLACEMENT................5  -  395.17XMTR REMOVAL AND REPLACEMENT...........................................................5  -  405.18XMT CRYSTAL OSCILLATOR FREQUENCY CORRECTION................................5  -  465.19XMTR OUTPUT LEVEL CHECK (NO PA)...........................................................5  -  475.20IN-SERVICE XMTR CARRIER NULL ADJUSTMENT  USING SPECTRUM ANALYZER.......................................................................5  -  485.21XMTR OUTPUT LEVEL CALIBRATION...............................................................5  -  565.22RCVR REMOVAL AND REPLACEMENT............................................................5  -  615.23RCV CRYSTAL OSCILLATOR FREQUENCY CORRECTION................................5  -  645.24PA REMOVAL AND REPLACEMENT................................................................5  -  655.25PA OUTPUT LEVEL CALIBRATION...................................................................5  -  675.26CHANGING FREQUENCY.............................................................................5  -  725.27CLEANING...................................................................................................5  -  72
TOC  -  5Section 6 User Guide6.1INTRODUCTION.............................................................................................6  -  16.2ANALOG SCREEN..........................................................................................6  -  16.2.1PA (DC MON).................................................................................................6  -  16.2.2TX (PWR MON)...............................................................................................6  -  16.2.3ATPC Voltage..................................................................................................6  -  16.2.4RX (RSL 1) dBm................................................................................................6  -  16.2.5RX (EYE MON)................................................................................................6  -  16.2.6RX (AFC MON)................................................................................................6  -  16.2.7Battery Voltage................................................................................................6  -  16.3DS1/E1 RADIO PERFORMANCE SCREEN........................................................6  -  36.3.1Repeater CRC Err Sec......................................................................................6  -  36.3.2Radio Severe Err Sec........................................................................................6  -  36.3.3Radio Outage Sec............................................................................................6  -  36.3.4Radio A and B Outage Sec..............................................................................6  -  36.3.5Radio CRC Err Sec...........................................................................................6  -  36.3.6Radio CRC Errors.............................................................................................6  -  36.3.7Radio Internal BER............................................................................................6  -  36.3.8Radio Average BER..........................................................................................6  -  36.4DS3 RADIO PERFORMANCE MONITORING SCREEN......................................6  -  56.4.1Line 1-3 DS3 Errors..........................................................................................6  -  56.4.2Line 1-3 DS3 BER.............................................................................................6  -  56.4.3Radio Errors.....................................................................................................6  -  56.4.4Radio Error Seconds.........................................................................................6  -  56.4.5Radio Severe Error...........................................................................................6  -  56.4.6Radio BER.......................................................................................................6  -  56.5OC3/STM-1 RADIO PERFORMANCE MONITORING SCREENS........................6  -  66.5.1OC3/STM-1 Errors..........................................................................................6  -  66.5.2OC3/STM-1 Error Seconds..............................................................................6  -  66.5.3OC3/STM-1 Severe Error Seconds...................................................................6  -  66.5.4OC3/STM-1 Severe Error Frame.......................................................................6  -  66.5.5OC3/STM-1 BER.............................................................................................6  -  66.5.6Line 1-3 DS1 Error Seconds..............................................................................6  -  66.5.7Radio Errors.....................................................................................................6  -  6
TOC  -  66.5.8Radio Error Seconds........................................................................................6  -  86.5.9Radio Severe Error...........................................................................................6  -  86.5.10Radio BER.......................................................................................................6  -  86.6ETHERNET RADIO PERFORMANCE MONITORING SCREEN.............................6  -  86.6.1RF Receive.......................................................................................................6  -  86.6.2GPF Receive....................................................................................................6  -  96.7ETHERNET PERFORMANCE MONITORING SCREEN........................................6  -  96.7.1IN (To RF Transmit)...........................................................................................6  -  96.7.2OUT (From RF Receive)...................................................................................6  -  106.8DS1/E1 RADIO CONTROL SCREEN..............................................................6  -  116.8.1In-Service Controls.........................................................................................6  -  116.8.2System Loopback Controls..............................................................................6  -  116.8.3User Controls.................................................................................................6  -  116.8.4DS1 Line Loopback Controls...........................................................................6  -  116.9DS3 RADIO CONTROL SCREEN....................................................................6  -  136.9.1In-Service Controls.........................................................................................6  -  136.9.2System Loopback Controls..............................................................................6  -  136.9.3User Controls.................................................................................................6  -  146.9.4Wayside DS1 Line Loopback Controls.............................................................6  -  146.10OC3/STM-1 RADIO CONTROL SCREEN........................................................6  -  166.10.1In-Service Controls.........................................................................................6  -  166.10.2System Loopback Controls..............................................................................6  -  166.10.3User Controls.................................................................................................6  -  166.11ETHERNET RADIO CONTROL SCREEN...........................................................6  -  186.11.1In-Service Controls.........................................................................................6  -  186.11.2User Controls.................................................................................................6  -  186.11.3System Loopback...........................................................................................6  -  196.11.4DS1 Line Loopback........................................................................................6  -  216.11.5Inventory Screen............................................................................................6  -  24
6  -  1The information contained in this section is a summary of the sec-tion with the same title, but not the same section number, on the  enclosed CD. “Refer to CD” is used throughout this section to refer  the reader to the detail information on the CD. Go to this section on  the CD for interactive links to the detail information referred to in  this section.6USER GUIDE6.1 INTRODUCTIONThis section contains descriptions of screens not used or described in other sections. Where there are operational differences, DS1/E1, DS3, and OC3/STM-1 and/or ETH screens are shown separately. 6.2 ANALOG SCREENSee Figure 6  -  1 and Figure 6  -  2. The Analog screen is used to display real-time analog voltages and radio performance monitors for the ELMC address. Analog voltages are updated automatically every second. Reset performance parameters to zero using the Error Reset button (or hotkey F3) on the toolbar. TIME SINCE LAST RESET displays the time in days, hours, minutes, and seconds since the last error reset.6.2.1 PA (DC MON)Indicates PA RF output level (Vdc).6.2.2 TX (PWR MON)Indicates XMTR module RF output level (Vdc).6.2.3 ATPC VoltageIndicates ATPC CONTROL signal output from controller to XMTR module(s) (Vdc).6.2.4 RX (RSL 1) dBmIndicates AGC MON output level from RCVR module (dBm).6.2.5 RX (EYE MON)Relative measure of noise level of receive signal (Vdc).6.2.6 RX (AFC MON)Indicates AFC MON output from single RCVR module (-3 Vdc = nominal frequency). (The AFC MON signal is developed from the correction voltage applied to the crystal oscillator on the single RCVR module.) Not provided by design and replaced with Path Distortion on dual RCVR module.6.2.7 Battery VoltageIndicates battery power input (Vdc).Note
6  -  2Figure 6  -  1  Analog Screen (Single RCVR)Figure 6  -  2  Analog Screen (Dual RCVR)TRANSMIT VoltagesA BPA (DC MON)3.13 3.03TX (PWR MON)1.91 1.95ATPC Voltage0.74 0.76RECEIVE VoltagesA BRX (RSL 1) dbm-45 dBm -53 dBmRX (EYE MON)0.09 0.19RX (AFC MON)-2.95 -2.95Battery Voltage-50.8 -51.0LOCAL ANALOGCommunicating*ELMC Address [F8]:ELMC Description:SILVERTONJ7915PerformanceAlarm StatusAnalog MonitorStation AlarmProvisioningUser ControlTuesday, July 29, 2003*Voltage not the same as PA Front Panel Test Point1:44:19 PM USI Version R1.06 Controller Version R1.06LMW-3123B01/29/04TRANSMITTERA BPA (DC MON)N/A N/ACOMMONA BBattery Voltage-53.5 -53.5TX (PWR MON)5.00 3.25ATPC Voltage0.76 0.74RECEIVERA BRX (RSL) (MN)-26 dBm -29 dBmRX (EYE MON) (MN)0.53 0.94Path Distortion (MN)2 1RX RSL (DV)-62 dBm -33 dBmRX (EYE MON) (DV)0.73 1.03Path Distortion (DV)3 2LOCAL ANALOGCommunicating***ELMC Address [F8]:ELMC Description:SILVERTONJ7915Tuesday July 29 2003*Voltage not the same as PA Front Panel Test Point1:44:19 PM USI Version R1 04 MDR 8000 OC3 Controller Version R1 04LMW-907301/29/04
6  -  36.3 DS1/E1 RADIO PERFORMANCE SCREENSee Figure 6  -  3. The Analog Monitor screen is used to display real-time analog voltages and radio performance monitors for the ELMC address. Analog voltages are updated automatically every second. Reset performance parameters to zero using the Error Reset button (or hotkey F3) on the toolbar. TIME SINCE LAST RESET displays the time in days, hours, minutes, and seconds since the last error reset.6.3.1 Repeater CRC Err SecRepeater CRC Errored Seconds, indicates number of seconds that contain coding viola-tions, slips, or frame losses in the data over the repeater cable. 6.3.2 Radio Severe Err SecRadio Severe Errored Seconds, indicates number of seconds that contain a predeter-mined number (N) of coding violations in the data over the RF path.6.3.3 Radio Outage SecRadio Outage Seconds, indicates on-line RCVR errored seconds (number of seconds that contain coding violations, slips, or frame losses in the data over the RF path).6.3.4 Radio A and B Outage SecRadio A and B Outage Seconds, indicates on-line and off-line RCVR errored in the same second.6.3.5 Radio CRC Err SecRadio CRC Errored Seconds, indicates number of seconds that contain coding viola-tions, slips, or frame losses in the data over the RF path.6.3.6 Radio CRC ErrorsIndicates number of errors in the data over the RF path.6.3.7 Radio Internal BERIndicates current BER of the data over the RF path.6.3.8 Radio Average BERIndicates average BER of the data over the RF path since last reset.
6  -  4Figure 6  -  3  DS1/E1 Radio Performance Monitor ScreenLOCAL PERFORMANCECommunicating*ELMC Address:lowerPERFORMANCE0 DAYS , 02:24:39ELAPSED TIME: Repeater CRC Err SecRadio Severe Err SecRadio Outage SecRadio A and B Outage SecRadio CRC Err SecRadio CRC ErrorsRadio Interval BERRadio Average BERA B000 000000.00E-1200000Thursday, March 16, 20002:15:29 PMLMW-800501/29/043 WAYS TO OPEN ANALOG MONITOR SCREEN3. PRESS F5 ON KEYBOARDFileAnalog and Performance Monitoring -- MDR-8000View Setup OptionsAlarm Status [F4] Perf Monitor [F5] Station Alarm [F6] Control [F7] Provisioning [F9]2. CLICK HEREError Reset [F3]Alarm StatusPerformanceStation AlarmControlProvisioningInventoryPower AdjustRSLF4F5F6F7F9F12Ctl+TCtl+R1. CLICK HERE
6  -  56.4 DS3 RADIO PERFORMANCE MONITORING SCREENSee Figure 6  -  4. Reset performance parameters to zero using the Error Reset button (or hotkey F3) on the toolbar. TIME SINCE LAST RESET displays the time in days, hours, minutes, and seconds since the last error reset.6.4.1 Line 1-3 DS3 ErrorsIndicates total number of coding violations, slips, or frame losses in the DS3 line data.6.4.2 Line 1-3 DS3 BERCalculated from code violation count and data rate.6.4.3 Radio ErrorsIndicates number of coding violations, slips, or frame losses in the data over the RF path.6.4.4 Radio Error SecondsAny second during which a code violation was detected.6.4.5 Radio Severe ErrorAny second during which the code violation count exceeds the number of errors that could occur in one second at 1 X 10-6 error rate.6.4.6 Radio BERCalculated from code violation count and data rate.Figure 6  -  4  DS3 Radio Performance ScreenTRANSMITTER A BLine 1 DS3 Errors24462 24462Elapsed Time: 1 Days, 02:41:23RECEIVER A BLine 1 DS3 Errors22629 22640Line 2 DS3 Errors24461 24461Line 2 DS3 Errors22630 22615Line 3 DS3 Errors24461 24461Line 3 DS3 Errors55635 22615Line 1 DS3 BER5.6 E-8 5.6 E-8Line 1 DS3 BER5.2 E-8 5.2 E-8Line 2 DS3 BER5.6 E-8 5.6 E-8Line 2 DS3 BER5.2 E-8 5.2 E-8Line 3 DS3 BER5.6 E-8 5.6 E-8Line 3 DS3 BER5.2 E-8 5.2 E-8Radio Errors784 0Radio Error Seconds1 0Radio Severe Error Seconds27 28Radio BER3.3 E-9 1.0 E-14LOCAL PERFORMANCECommunicating*ELMC Address:ELMC Description:SILVERTONJ7915Monday, July 28, 2003 1:44:19 PM USI Version R1.07 Controller Version R1.07LMW-3123A01/29/04
6  -  66.5 OC3/STM-1 RADIO PERFORMANCE MONITORING SCREENSSee Figure 6  -  5, Figure 6  -  6, and Figure 6  -  7. Reset performance parameters to zero using the Error Reset button (or hotkey F3) on the toolbar. TIME SINCE LAST RESET displays the time in days, hours, minutes, and seconds since the last error reset.6.5.1 OC3/STM-1 ErrorsIndicates total number of coding violations, slips, or frame losses in the OC3/STM-1 data.6.5.2 OC3/STM-1 Error SecondsAny second during which a code violation was detected. Count is initiated during any second that qualifies as Unavailable Second.6.5.3 OC3/STM-1 Severe Error SecondsAny second during which the code violation count exceeds the number of errors that could occur in one second at 1 X 10-6 error rate. Count is inhibited during any second that qualifies as Unavailable Second.6.5.4 OC3/STM-1 Severe Error FrameAny second during which there is no start of frame for at least four consecutive frames.6.5.5 OC3/STM-1 BERCalculated from code violation count and data rate.6.5.6 Line 1-3 DS1 Error SecondsAny second during which a code violation was detected on the wayside DS1 line.6.5.7 Radio ErrorsIndicates number of coding violations, slips, or frame losses in the data over the RF path.Figure 6  - 5  OC3/STM-1 Radio, OC3/STM-1 Facilities Performance ScreenWaySide DS1Radio OC3Error Seconds 10 0TRANSMITTER (IN) A BErrors 942 0Severe Error Seconds100 0Severe Error Frame Seconds2 0BER1.0 E-8 0Time Since Errors Reset: 0 Days, 00:00:00Error Seconds 12 0RECEIVER (OUT) A BErrors 1192 0Severe Error Seconds120 0Severe Error Frame Seconds30 0BER5.2 E-7 1.0 E-14Monday, July 28, 20033:30:05 PM USI Version R1.04 Controller Version R1.04MDR-8000 OC3LMW-507201/29/04
6  -  7Figure 6  -  6  OC3/STM-1 Radio, Wayside DS1 Facilities Performance ScreenFigure 6  -  7  OC3/STM-1 Radio, Radio Performance ScreenELMC Address:ELMC Description:LOCAL PERFORMANCEWAYSIDE DS1RADIOCommunicating**OC3Line 2 DS1 Error Seconds 0 0TRANSMITTER A BLine 1 DS1 Error Seconds 12 0Line 3 DS1 Error Seconds 0 0Time Since Errors Reset: 0 Days, 00:00:00Line 1 DS2 Error Seconds 0 0RECEIVER A BLine 1 DS1 Error Seconds 15 0Line 1 DS3 Error Secondss0 0Monday, August 20, 2001 3:30:05 PM USI Version R1.01 Controller Version R1.01MDR-8000 OC3LMW-507301/29/04WAYSIDE DS1OC3PerformanceAlarm Status Station Alarm User Control ProvisioningError Reset Analog MonitorELMC Address:ELMC Description:LOCAL PERFORMANCERadioCommunicating***657Error Seconds 27 0ErrorsRECEIVER A B2143 0Severe Error Seconds5 0Severe Error Frame Seconds1 0BER5.2 E-7 0Radio Outage SecRadio A and B Outage Sec00Time Since Errors Reset: 0 Days, 00:00:00Monday, July 28, 2003 3:41:41 PM USI Version R1.04 Controller Version R1.04MDR-8000 OC3R101OC3 6GHz TopLMW-507401/29/04
6  -  86.5.8 Radio Error SecondsAny second during which a code violation was detected. Count is initiated during any second that qualifies as Unavailable Second.6.5.9 Radio Severe ErrorAny second during which the code violation count exceeds the number of errors that could occur in one second at 1 X 10-6 error rate. Count is inhibited during any second that qualifies as Unavailable Second.6.5.10 Radio BERCalculated from code violation count and data rate.6.6 ETHERNET RADIO PERFORMANCE MONITORING SCREENSee Figure 6  -  8. Reset performance parameters to zero using the Error reset button on the toolbar. TIME SINCE LAST RESET displays the time in days, hours, minutes and seconds, since the last error reset.6.6.1 RF Receive6.6.1.1 ErrorsIndicates total number of coding violations, slips, or frame losses in the Ethernet data.6.6.1.2 Error SecondsAny second during which a code violation was detected. Count is initiated during any second that qualifies as Unavailable Second.6.6.1.3 Severe Error SecondsAny second during which the code violation count exceeds the number of errors that could occur in one second at 1x 10-6 error rate. Count is inhibited during any second that qualifies as Unavailable Second.6.6.1.4 Severe Error Frame SecondsAny second during which there is no start of frame for at least four consecutive frames.6.6.1.5 BERCalculated from code violation count and data rate.6.6.1.6 Radio Outage SecRadio Outage Seconds, indicates on-line RCVR errored seconds (number of seconds that contain coding violations, slips, or frame losses in the data over the RF path).6.6.1.7 Radio A and B Outage SecRadio A and B Outage Seconds, indicates on-line and off-line RCVR errored in the same second.
6  -  9Figure 6  -  8  Ethernet Radio, Radio Performance Screen6.6.2 GPF Receive6.6.2.1 ErrorsIndicates total number of coding violations, slips, or frame losses in the Ethernet data.6.6.2.2 Error SecondsAny second during which a code violation was detected. Count is initiated during any second that qualifies as Unavailable Second.6.6.2.3 Severe Error SecondsAny second during which the code violation count exceeds the number of errors that could occur in one second at 1 x 10-6 error rate. Count is inhibited during any second that qualifies as Unavailable Second.6.6.2.4 Severe Error Frame SecondsAny second during which there is no start of frame for at least four consecutive frames.6.7 ETHERNET PERFORMANCE MONITORING SCREENSee Figure 6  -  9. Reset performance parameters to zero using the Error reset button on the toolbar. TIME SINCE LAST RESET displays the time in days, hours, minutes, and seconds since the last error reset.6.7.1 IN (To RF Transmit)6.7.1.1 Average Bytes/SecIndicates average number of frame bytes per second in the Ethernet RCV/radio XMT data.Communicating*RF RECEIVE A0Errors2Error seconds2Severe Error Seconds2Severe Error Frame Seconds1.0 E-14BER2Radio Outage Sec2Radio A and B Outage SecGFP RECEIVE AB00001.1 E-14B4Errors 012Error Seconds 012Severe Error Seconds 04 0Severe Error Frame Seconds2.9 E-12 1.5 E-12BEREthernetRadioMDR-120208/15/05
6  -  106.7.1.2 Total FramesIndicates number of valid Ethernet frames in the Ethernet RCV/radio XMT data.6.7.1.3 Error FramesFrame Check Sequence (FCS) error count indicates the number of Ethernet frames with errors in the Ethernet RCV/radio XMT data.6.7.1.4 Dropped FramesIndicates number of Ethernet frames dropped due to errors in the Ethernet RCV/radio XMT data or lack of buffer space.Figure 6  -  9  Ethernet Radio, Ethernet Performance Screen6.7.2 OUT (From RF Receive)6.7.2.1 Average Bytes/SecIndicates average number of frame bytes per second in the Ethernet XMT/radio RCV data.9, 084, 928LOCAL PERFORMANCE (RS 232)Communicating*IN (to RF TRANSMIT) AAverage Bytes / Sec8.655579 E+9Total Frames0Error Frames65, 520Dropped FramesTime Since Errors Reset: 3 Days, 23:45:559, 519, 104OUT (from RF RECEIVE) AAverage Bytes / Sec1.164721 E+10Total Frames5, 431, 296Error Frames5, 431, 2964, 013, 824B1.804514 E+9043, 6820B1.316459 E+93499534742Dropped FramesEthernetRadioMDR-120308/15/05
6  -  116.7.2.2 Total FramesIndicates number of valid Ethernet frames in the Ethernet XMT/radio RCV data.6.7.2.3 Error FramesFrame Check Sequence (FCS) error count indicates the number of Ethernet frames with errors in the Ethernet XMT/radio RCV data.6.7.2.4 Dropped FramesIndicates number of Ethernet frames dropped due to errors in the Ethernet XMT/radio RCV data, or lack of buffer space.6.8 DS1/E1 RADIO CONTROL SCREENSee Figure 6  -  10. The Control screen is used to enable or disable and display the status of manual controls. Manual controls include equipment and function in-service con-trols, system loopback controls, user controls, and DS1/E1 loopback controls. The green square indicates control is enabled. Highlight and click on control name to change state.6.8.1 In-Service ControlsIN-SERVICE controls are used to force A or B transmitter, receiver, and I/O interface modules on -or off-line. IN-SERVICE manual controls are also used to lock the A or B transmitter ATPC function high (ATPC High Pwr Lock) or low (ATPC Low Pwr Lock).6.8.2 System Loopback ControlsWhen enabled, SYSTEM LOOPBACK manual controls loop I/O receiver to I/O trans-mitter (I/O LOOPBACK). I/O LOOPBACK is a local loopback function that can be used to test the performance of a standalone radio.6.8.3 User ControlsUSER CONTROLS, defined by the customer and named on the User Control Names Setup screen, are displayed and can be enabled or disabled if the optional AE-37( ) Relay Interface module is installed.6.8.4 DS1 Line Loopback ControlsSee Figure 6  -  11. When enabled, DS1 LINE LOOPBACK RCV to XMT manual controls loop DS1/E1 lines individually (Line 1-16 loopback). DS1 LINE LOOPBACK RCV to XMT is a far-end loopback function that can be used to test over-the-hop.
6  -  12Figure 6  -  10  DS1/E1 Radio Control ScreenLOCAL CONTROLCommunicatingELMC Address:Description:DURANGOJ7914Thursday, March 16, 200010:15:49 AMIN-SERVICEA Transmitter On LineB Transmitter On LineA Receiver On LineA I/O On LineB I/O On LineB Receiver On LineA ATPC High Power LockB ATPC High Power LockA ATPC Low Power LockB ATPC Low Power LockLine 1 loopbackLine 2 loopbackLine 3 loopbackLine 4 loopbackLine 5 loopbackLine 6 loopbackLine 7 loopbackLine 8 loopbackLine 9 loopbackLine 10 loopbackLine 11 loopbackLine 12 loopbackLine 13 loopbackLine 14 loopbackLine 15 loopbackLine 16 loopbackSYSTEM LOOPBACKI/O LOOPBACKUSER CONTROLSGEN STARTTWR LIGHT OVRDUser Control #3User Control #4User Control #5User Control #6DS1 LINE LOOPBACK RCV to XMT2. CLICK HERE3 WAYS TO OPEN CONTROL SCREEN3. PRESS F7 ON KEYBOARDFileControls -- MDR-8000 DS1View Setup OptionsAlarm Status [F4] Perf Monitor [F5] Station Alarm [F6] Control [F7] Provisioning [F9]Alarm StatusPerformanceStation AlarmControlProvisioningInventoryPower AdjustRSLF4F5F6F7F9F12Ctl+PCtl+R1. CLICK HERELMW-100601/29/04ACTIVEHIGHLIGHT AND SELECT "YES" ON CONFIRMATION MESSAGE TO ENABLE FUNCTION
6  -  13Figure 6  -  11  DS1/E1 Loopback6.9 DS3 RADIO CONTROL SCREENSee Figure 6  -  12. The Control screen is used to enable or disable and display the status of manual controls. Manual controls include equipment and function in-service con-trols, system loopback controls, user controls, and DS1/E1 loopback controls. The green square indicates control is enabled. Highlight and click on control name to change state.6.9.1 In-Service ControlsIN-SERVICE controls are used to force A or B transmitter, receiver, and I/O interface modules on-or off-line. IN-SERVICE manual controls are also used to lock the A or B transmitter ATPC function high (APC High Pwr Lock) or low (APC Low Pwr Lock).6.9.2 System Loopback ControlsSee Figure 6  -  13.When enabled, SYSTEM LOOPBACK manual controls loop I/O receiver to I/O transmitter (I/O LOOPBACK). I/O LOOPBACK is a local loopback func-tion that can be used to test the performance of a standalone radio.MUXXMTRCVDEMUXI/O INTFCMODULEXMTRMODULELMW-607207/05/04I/O INTFCMODULERCVRMODULEDS1 LINE ( ) LOOPBACK(PER DS1)I/O LOOPBACK(ALL DS1s)
6  -  146.9.3 User ControlsUSER CONTROLS, defined by the customer and named on the User Control Names Setup screen, are displayed and can be enabled or disabled if the optional AE-27() Relay Interface module is installed.6.9.4 Wayside DS1 Line Loopback ControlsSee Figure 6  -  13. When enabled, DS1 LINE LOOPBACK RCV to XMT manual controls loop DS1/E1 lines, individually (Line 1-16 loopback). DS1 LINE LOOPBACK RCV to XMT is a far-end loopback function that can be used to test over-the-hop.Figure 6  -  12  DS3 Radio Control ScreenFileControls  MDR 8000 DS3View Setup OptionsAlarm Status Performance Station Alarm User Control ProvisioningAnalog MonitorF4 F5 F6 F7 F8 F9LOCAL CONTROLSCommunicating*ELMC Address:Description:SILVERTONA Transmitter On LineB Transmitter On LineA Receiver On LineB Receiver On LineA I/O On LineB I/O On LineA ATPC HIGH Power LockB ATPC HIGH Power LockA ATPC LOW Power LockB ATPC LOW Power LockJ7915IN-SERVICEA I/O LOOPBACKLine 1 FacilityLine 2 FacilityLine 3 FacilityLine 1 EquipmentLine 2 EquipmentLine 3 EquipmentB I/O LOOPBACKControl #1Control #2Control #3Control #4Control #5Control #6SYSTEM LOOP-BACKDS3 LINE LOOP-BACKUSER CONTROLSThursday, November 30, 2000 1:44:19 PM USI Version R1.02 Controller Version R1.02LMW-311705/14/06
6  -  15Figure 6  -  13  DS3 System LoopbackUNI XMTASIC ENFEC TOXMTRI/Q I/QUNI RCVASICDEFECFROMRCVRLMW-505607/05/04I/Q I/QI/QDS3 LINE 1-3DS3 I/O INTFCFROMCONTROLLERDS3 LINE 1-3LOOPBACK ENABLETO/FROMDS3 LBOI/OLOOPBACK(ALL DS3s)SW SWITCHLOOPBACK I/OCONTROLENABLED
6  -  166.10 OC3/STM-1 RADIO CONTROL SCREENSee Figure 6  -  14. and Figure 6  -  15 The Control screen is used to enable or disable and dis-play the status of manual controls. Manual controls include equipment and function in-service controls, system loopback controls, user controls, and DS1/E1 loopback controls. The green square indicates control is enabled. Highlight and click on control name to change state.6.10.1 In-Service ControlsIN-SERVICE controls are used to force A or B transmitter, receiver, and I/O interface (OC3/STM-1) modules on-or off-line. IN-SERVICE manual controls are also used to lock the A or B transmitter ATPC function high (ATPC High Power Lock) or low (ATPC Low Power Lock).6.10.2 System Loopback ControlsSee Figure 6  -  16 for SYSTEM LOOP-BACK. All loopbacks occur in the SMCRA on the I/O interface module. Loopback functions in both directions are bridged type functions. Data both loops back and continues. Loopbacks are named by facility in the direction of the loop. When enabled, A/B OC3/STM-1 Facility loops the optical RCV/radio XMT input to the radio RCV/optical XMT output. When enabled, A/B OC3/STM-1 Equipment loops the demultiplexed RCV output of the DEMUX circuit into the input to the MUX circuit.When enabled, A/B RC3 Equipment loops the output of the MUX circuit into the input of the DEMUX circuit.6.10.3 User ControlsUSER CONTROLS, defined by the customer and named on the User Control Names Setup screen, are displayed and can be enabled or disabled if the optional AE-27( ) Relay Inter-face module is installed.
6  -  17Figure 6  -  14  OC3/STM-1 Radio Control Screen (Single RCVR)Figure 6  -  15  OC3/STM-1 Radio Control Screen (Dual RCVR)Communicating*ELMC Address:Description: DALLASA Transmitter OnlineB Transmitter OnlineA Receiver OnlineB Receiver OnlineA OC3 InputB OC3 InputA OC3 OutputB OC3 OutputA Wayside DS1 OnlineB Wayside DS1 OnlineRK201IN-SERVICEA ATPC High Power LockB ATPC High Power LockA ATPC Low Power LockB ATPC Low Power LockUSER CONTROLS SYSTEM LOOP-BACKATPC POWER LOCKControl #1Control #2Control #3Control #4A OC3 FacilityA RC3 EquipmentA OC3 EquipmentB OC3 FacilityB RC3 EquipmentB OC3 EquipmentControl #5Control #6Thursday, April 16, 2002 1:47:10 PM USI Version R1.01 MDR-8000 OC3         Controller Version R1.01LMW-608401/29/04LOCAL CONTROLSCommunicatingELMC Address:A Transmitter On LineB Transmitter On LineA Receiver On LineB Receiver On LineA OC3 InputB OC3 InputDR301IN-SERVICEA OC3 Facility B OC3 FacilityA RC3 Equipment B RC3 EquipmentA OC3 Equipment B OC3 EquipmentSYSTEM LOOP-BACKA Main A DiversityB Main B DiversityFORCED SWITCHINGA OC3 OutputB OC3 OutputMonday, July 28, 20031:06:08 PM USI Version R1.04 MDR-8000 OC3   Controller Version R1.04LMW-907501/29/04
6  -  18Figure 6  -  16  OC3/STM-1 Loopbacks6.11 ETHERNET RADIO CONTROL SCREENSee Figure 6  -  17. The Control screen is used to enable or disable and display the status of manual controls. Manual controls include equipment and function in-service con-trols, system loopback controls, user controls, and DS1 loopback controls. The green square indicates control is enabled. Highlight and click on control name to change state.6.11.1 In-Service ControlsIn service controls are used to force A or B transmitter, receiver, and I/O interface mod-ules on-or off-line. IN-SERVICE manual controls are also used to lock the A or B trans-mitter ATPC function high (ATPC High Power Lock) or low (ATPC Low Power Lock).6.11.2 User ControlsUSER CONTROLS, defined by the customer and named on the User Control Names Setup screen, are displayed and can be enabled or disabled if the optional AE-27( ) Relay Interface module is installed.MUXSwitchCMDSwitchCMDOT/RROR/RTRT4 x 39TranslatorSMCRAI/O INTFC XMTRRRRCVRMDR-109412/14/04OC3FacilityLPBKOC3EquipmentLPBKMUXSwitchCMDRC3EquipmentLPBKMUXIOIOIO
6  -  196.11.3 System LoopbackSee Figure 6  -  18 for the system loopback functions. There are three system loopback functions available on the Ethernet radio; Eth facility loopback, RC3 equipment loop-back, and Eth equipment loopback. All loopbacks occur on the Ethernet I/O interface module. The loopback functions are controlled by software via the SYSTEM LOOP-BACK controls on the USI Control screen.6.11.3.1 Eth Facility LoopbackEth facility loopback is a local loopback function that can be used to test the perfor-mance of a standalone radio. Eth Facility loopback is enabled by selecting A Eth Facil-ity under SYSTEM LOOPBACK on the USI Control screen. This function loops the Ethernet RCV/radio XMT (EthR/RT) input back into the Ethernet XMT/radio RCV (EthT/RR) output. The actual loopback occurs in the PHY circuits on the I/O interface. When enabled, the EthR/RT input is switched through the MUX to the EthT/RR out-put. The Eth/R/RT input also continues through the MUX to the ETHRA FPGA.Figure 6  -  17  Ethernet Radio, Ethernet Control Screen201R2LOCAL CONTROLS (RS-232)Communicating**IN-SERVICE IN-SERVICEA Ethernet FacilityA Radio EquipmentA Ethernet EquipmentB Ethernet FacilityB Radio EquipmentB Ethernet EquipmentControl #1Control #2Control #3Control #4Control #5Control #6SYSTEM LOOP-BACKLine 1 FacilityLine 2 FacilityLine 3 FacilityLine 4 FacilityLine 1 EquipmentLine 2 EquipmentLine 3 EquipmentLine 4 EquipmentDS1 LINE LOOP-BACK RCV to XMTELMC Address:A Transmitter On LineB Transmitter On LineA Receiver On LineB Receiver On LineA Ethernet In ActiveB Ethernet In ActiveA Ethernet Out ActiveB Ethernet Out ActiveA Ethernet OnlineB Ethernet OnlineA DS1 OnlineB DS1 OnlineMDR-120408/08/05
6  -  20Figure 6  -  18  Ethernet Loopbacks6.11.3.2 RC3 Equipment LoopbackRC3 equipment loopback is a local loopback function that can be used to test the per-formance of a standalone radio. RC3 Equipment loopback is enabled by selecting A RC3 Equipment under SYSTEM LOOPBACK on the USI Control screen. This func-tion loops the Eth RCV/radio XMT (EthR/RT) input back into the EthXMT/radio RCV (EthT/RR) output. The actual loopback occurs in the ETHRA FPGA on the I/O inter-face. When enabled, the radio XMT (RT) output is switched through the MUX in the ETHRA, replacing the radio RC (RR) input. The radio XMT (RT) output also continues to the XMTR RT output. PHYMAC FIFO GFPRADIOFRAMEMULDEMETH TXDS1 LINE  INTFCETH RXSWCMDSWCMDSWCMDSWCMDSWCMDTI/DS1FRAMINGETHEQUIPLPBKETHFACILITYLPBKETH RC3 LPBK(DATA + OH + WSDS1)ETHRA FPGAWS DS1 LINE  1 2 3 4 4 3 2WS DS1 LINE  1ETH-104601/25/06
6  -  216.11.3.3 Eth Equipment LoopbackEth equipment Loopback is a farend loopback function that can be used to test the over-the-hop performance of radios. Eth Equipment loopback is enabled by selecting A Eth Equipment under SYSTEM LOOPBACK on the USI Control screen. This function loops the radio RCV (RR) input into the radio XMT output. The actual loopback occurs in the PHY circuits on the I/O interface. When enabled, the radio RCV (RR) input is switched through the MUX in the ETHRA and through the MUX in the PHY, replacing the Eth RCV/radio XMT (EthR/RT) output to the ETHRA. The radio RCV (RR) input also continues through the MUX in the PHY to the EthT/RR output.6.11.4 DS1 Line LoopbackThere are two individual DS1 line loopback functions available on the Ethernet radio Control screen; Line facility Loopback and Line Equipment Loopback. All loopbacks occur on the Ethernet I/O interface module. The DS1 line loopback functions are con-trolled by software via the DS1 LINE LOOPBACK controls on the USI Control screen.6.11.4.1 DS1 Line Facility LoopbackSee Figure 6  -  19 for functional block diagram. DS1 facility loopback is a local loopback function that can be used to test the performance of a standalone radio. Individual DS1 line facility loopback is enabled by selecting Line 1, 2, 3, or 4 Facility under DS1 LINE LOOPBACK on the USI Control screen. This function loops the DS1 RX1, 2, 3, or 4 Tip and Ring inputs to the DS1 TX1, 2, 3, or 4 Tip and Ring outputs. The actual loopback occurs in the QuadFalc FPGA on the I/O interface. When enabled, the DS1, RX1, 2, 3, or 4 Tip and Ring inputs are switched through the MUX in the QuadFalc, replacing the radio inputs from the ETHRA. The radio DS1 Rx1, 2, 3, or 4 Tip and Ring output of the QuadFalc also continues to the ETHRA FPGA.6.11.4.2 DS1 Line Equipment LoopbackSee Figure 6  -  20 for a functional block diagram. DS1 Equipment Loopback is a farend loopback function that can be used to test the performance of radios over the hop. Indi-vidual Line Equipment facility loopback is enabled by selecting Line 1, 2, 3, or 4 Equipment under DS1 LINE LOOPBACK on the USI Control screen. This function loops the DS1 TX1, 2, 3, or 4 Tip and Ring inputs from the RCV circuits on the ETHRA to the DS1 RX1, 2, 3, or 4 Tip and Ring outputs of the QuadFalc to the XMT circuits in the ETHRA. The loopback occurs in the QuadFalc FPGA on the I/O interface. When enabled by the switch command, the DS1 TX1, 2, 3, or 4 Tip and Ring inputs are switched through the MUX in the QuadFalc, replacing the radio DS1 inputs from the AUX interface. The radio DS1 TX1, 2, 3, or 4 output of the QuadFalc continues to the AUX interface board.
6  -  22Figure 6  -  19  DS1 Facility Loopback – EthernetDS1 TX 3 T/RDS1 TX 4 T/RIOSwitchCMDIOSwitchCMDDS1 RX 2 T/RIOSwitchCMDDS1 RX 3 T/RDS1 RX 4 T/RIOSwitchCMDDS1 RX 1 T/RQuad FalcDS1 TX 1 T/RDS1 TX 2 T/RAUXINTFCBoardETHRAFPGAMDR-116404/28/05CAUTIONPossibility ofServiceInterruptionLoopbacks cause loss of traffic on DS1 outputs to X-connect.Line 4 available in Terminal configuration. Not available in Repeater configuration.Note
6  -  23Figure 6  -  20  DS1 Equipment Loopback – EthernetIOSwitchCMDIOSwitchCMDIOSwitchCMDSwitchCMDIOQuad FalcDS1 TX 3 T/RDS1 TX 4 T/RDS1 RX 2 T/RDS1 RX 3 T/RDS1 RX 4 T/RDS1 RX 1 T/RDS1 TX 1 T/RDS1 TX 2 T/RAUXINTFCBoardETHRAFPGAMDR-117105/31/05CAUTIONPossibility ofServiceInterruptionLoopbacks cause loss of traffic on DS1 inputs to ETHRA FPGA.Line 4 available in Terminal configuration. Not available in Repeater configuration.Note
6  -  246.11.5 Inventory ScreenSee Figure 6  -  21 for Inventory Screen. The inventory screen is used to display current shelf inventory, including module type number, module part number, hardware revi-sion, software revision (if applicable), serial number, and remarks (if any).Inventory is automatically updated if modules are replaced. Manual changes to the inventory list on the screen are performed only in the factory.Figure 6  -  21  Inventory ScreenTuesday, November 30, 2004 3:31:44 PM Universal USI Version P2.00q MDR-8000 OC3         Controller Version P3.13Side A CommonSide BExportCancel ClearRefreshStoreSelect All TYPE Part Number RV MRev ICS S/W REV Serial Number MiscTransmitter UD-35AQ-4 3DH03236AD AA 01 01  CA02D546Transmitter Cap Key N/A 3EM04177AB AB 02 0100CA07D577Transmitter Oscillator N/A 3DH04123AC AB 01Power Amplifier UD-16BB-2 3DH03218AA AA 03 01   L50W8389Power Supply DS-35P-2 3DH03164AB AB 01 01 EM1I/O Interface UD-36AQ-10 3EM03134AB AB 01 01 R02.01 CA09W929CA09W146Receiver AE 27AF-1 3DH03239AD3EM04177ABAA 01 0101  CA02D619Receiver Cap Key N/AReceiver Oscillator N/A 3DH04123AC AA 01 00  02ABELMC Address: R101LOCAL INVENTORY (RS-232)Communicating***Alcatel User Interface – [Universal USI -- Inventory]F6PerformanceAlarm StatusF4Station AlarmF7 F9User ControlF8F5Prov. SaveF3ProvisioningFile View Setup OptionsMDR-116211/21/06Realization Variant - identifies differences in design within family itemField Not ApplicableManufacturing Revision - identifies enhancement-type changesItem Change Status - identifies source of part

Navigation menu