Alarm com orporated 143600T Z-Wave adds remote control to home automation and security systems User Manual
Alarm.com Incorporated Z-Wave adds remote control to home automation and security systems
UserManual.wiki
>
Alarm com orporated
>
143600T User Manual
User Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Copyright © 2014 Alarm.com | www.alarm.com | v1.0 2 Impassa Broadband Module| Installation Guide sure that the edge of the module sits below the plastic tabs located at the top of the panel. Push the other end of the module downwards, until it sits below the plastic tab located at the bottom of the panel. 4) Connect the module to the panel via the 16 pin ribbon cable. The ribbon connector is located at the top of the module. On the panel the ribbon connector is located directly across from the connector on the module. 5) Connect the Broadband-enabled Alarm.com system to the Internet using a standard Ethernet (RJ-45) cable. The cable should be connected at one end to the local Internet access point (network router), and at the other end to the RJ-45 jack on the Alarm.com module. Power Up Reconnect panel battery and AC power. When a broadband module is connected to a powered control panel, the LEDs at the bottom of the module will become active (see Table 1 on page 4). It may take a few moments after power up for the LEDs to become active. If the LEDs do not light up at all, ensure that the module has been fully connected to the panel via the ribbon cable then perform a full power cycle by following these steps: 1. Disconnect the battery leads and unplug the panel power transformer from AC power. 2. Verify that the module is inserted securely. 3. Connect battery leads to the battery. Make sure to observe polarity (red to + and black to –) and to keep the wires outside of the tab holding them in place. 4. Plug the panel power transformer into the AC outlet. It is important to plug the battery in before plugging in the transformer, otherwise the panel will issue a “System Low Battery” message regardless of the battery voltage level. Note that power cycling will clear existing banners. Comm Test (Module Registration) To initiate module communication with Alarm.com the first time, perform a “Comm test”. To perform the comm test on an Impassa press [*][6] followed by the master code and [4]. The Impassa panel will let you know when the comm test has completed by activating the siren output on medium volume for 2 seconds followed by full volume alarm for 2 seconds. All display lights and LCD pixels turn on. This indicates that Alarm.com has received and acknowledged the signal. This does not guarantee that the signal went through to a central station; it confirms that the Alarm.com Operations Center received the signal. The central station should be contacted directly to verify that the signal was received on the correct account and that the Central Station routing settings have been set up correctly. The signal may not go through to the central station if (a) the Central Station Account settings were entered incorrectly on the Alarm.com Dealer Site or (b) if Alarm.com was unable to send the signal successfully to the Central Station receivers. Panel Settings Night Arming The Impassa panel has the ability to night arm, which arms the perimeter and restricts movement to designated interior areas. Night arming via the panel should be restricted to one of the five function keys. For more information on Night Arming and how to program the function keys see the installation guide provided with the panel. Panel Settings Automatically Change Some panel settings are changed automatically when the broadband module is connected to the control panel. These settings should not be altered. They are: Clock: The broadband module sets the panel clock when it connects to Alarm.com and then updates it every 18 hours. It is important to select the correct panel time zone on the Alarm.com website, or the panel time will not be accurate. If a system is powered up before the customer account has been created, the time zone will default to Eastern Time Specifications Compatibility Impassa panels Power requirements 3.9V Standby current 3.9mA Peak current 325mA Operating temperature 14 to 131°F (-10 to 55°C) Storage temperature -30 to 140°F (-34 to 60°C) Max. relative humidity 90% non-condensing Network Broadband Dimensions (H x W) 3.25 x 4.25 in. (8.23 x 10.80 cm.) Regulatory Information Changes or modifications not expressly approved by Alarm.com can void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment in to an outlet on a circuit different from that which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres](https://usermanual.wiki/Alarm-com-orporated/143600T/User-Guide-2177081-Page-3.png)
