Aeon Labs FT121 LED Strip, ColorStrip User Manual

Aeon Labs LLC. LED Strip, ColorStrip

User Manual

Aeotec by Aeon Labs LED Strip.134Aeotec LED Strip is a multi-coloured LED Strip which allows control (on/off/dim/colour change) via wireless Z-Wave commands. The LED Strip can also communicate securely via AES 128 wireless Z-Wave commands and supports Over-The-Air (OTA) rmware upgrades.Package Contents:1.2.3.1.2.3.Plug the LED strip to the LED strip connector of your LED Strip Controller. Connect the Power Adapter to your LED Strip.Plug the Adapter into an electrical outlet and then the Set your Z-Wave controller into pairing mode.Press the Action Button on the LED Strip.If the LED Strip has been successfully added to your Z-Wave network, its Network LED will be solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colourful gradient, repeat the instructions above from step 1.Familiarise yourself with your LED Strip.Quick start.With your LED Strip now working as a part of your smart home, you’ll be able to congure it to indicate different colours from your home control software via setting the RGB value. Please refer to the user manual for your Z-Wave controller/gateway for precise instructions on conguring your LED Strip to your needs.Your LED Strip can be removed from your Z-Wave network at any time. You’ll need to use your Z-Wave network’s main controller. To set your Z-Wave controller/gateway into removal mode, please refer to the respective section within your Z-Wave controller instruction manual.Install your LED Strip. 7 6 543210Value 1 (MSB) Colour Transition StyleColour Change Speed OptionColour Display CycleValue 2 BrightnessValue 3 Cycle CountValue 4 (LSB) Time Base of CoulorChange Speed Colour Change Speed LevelRemoving your LED Strip from a Z-Wave network.Advanced functions.Colour Display Cycle Configuration.Parameter 37 [4 byte] will cycle the colour displayed by LED Strip into different modes:The Colour Display Cycle field can have the following values corresponding to 4 different modes:The Cycle Count is used to dene the number of repetitions/cycles displayed by your LED Strip in Colour Display Cycle before stopping.Colour Display Cycle (4 bits)The following values correspond to 2 different transition styles between colours: Cycle Count (8 bits)Colour Display Cycle Description0Inactive (keep the current conguration values)1Rainbow Mode(red, orange, yellow, green, cyan, blue, violet)2Multi Colour Mode(colours cycle between selected colours)3 Random Mode.4 Single Colour Mode.5 to15 Reserved.Colour Transition Style Description0 Smooth Colour Transition.1 Fade Out Fade In Transition.Cycle Count Description0 Unlimited.1 to 254 Total number of repetitions/cycles before stopping.255 Inactive (keep the current conguration values).Colour Transition Style (2 bits)This function would be used when the Colour Transition Style is set to Fade Out/In.The table above shows a decimal representation of the settings that can be set on parameter 37.This function would be used when the Colour Transition Style is set to Fade Out/In.Time Base of Colour Change Speed (3 bits)Colour Change Speed Level (5 bits)Speed Level Description0 Constant speed.1 to 30 Accelerate/decelerate speed from the level 1 to 30.31 Inactive (keep the current conguration values).Parameter 39 [4 byte] can be used to set up to 8 colours to cycle between when LED Strip is in Multi Colour Mode. Colours transition from Colour Index 1-8.2Brightness Level Description1 to 99 1 = Min level. 99 = Max level.0 or 255 Inactive (keep the current conguration values).Brightness (8 bits)Time Base Description0 Time base is 1s.1 Time base is 10ms.2 Time base is 100ms.1.2.Set your Z-Wave controller into device removal mode.Press the Action Button on the LED Strip.7 6 543210Value 1 (MSB) Index 1 Index 2Value 2 Index 3 Index 4Value 3 Index 5 Index 6Value 4 (LSB) Index 7 Index 8View the expanded manual:http://aeotec.com/supportLED StripIMPORTANT!This product has been fully tested and certied to work with Z-Wave by the Z-Wave Alliance. It is crafted using Z-Wave Plus, the latest device version of Z-Wave. As such, if the product does not work with your gateway, please be sure to check with your gateway manufacturer that they have integrated this device with their gateway for full operation.LED Strip Controller Back Mount Plate ScrewsDouble-Sided Tape 1. LED Strip Controller (×1)2. Screws (×2)3. Back Mount Plate (×1)4. 5 meters LED strip (×1)5. Power Adapter (×1)6. Double-Sided Tape (×1)Adding your LED Strip to a Z-Wave network.You are now able to manually control the LED Strip directly via pressing your LED Strip’ Action Button. It is time to add your LED Strip to your Z-Wave network. To set your Z-Wave gateway/controller into pairing mode, please refer to the respective section within your controller instruction manual.Power Adapter The installation of your LED Strip has two major steps: the LED Strip Controller and the LED Strip. LED Strip can be installed inside or outside your home, but the LED Strip Controller should only be installed inside your home and should not be installed outdoors in elements such as rain and snow.Network LED Action Button Power Input LED Strip ConnectorLED StripIf the LED Strip has been successfully removed from your Z-Wave network, its Network LED will remain colourful gradient. If the removal was unsuccessful, the Network LED will still be solid, repeat the instructions above from step 1.LED StripLED Strip ControllerPower Socket4.Network LED on LED Strip Controller will blink slowly to indicate it is ready to be paired to your Z-Wave network.Now press the Action Button to toggle your LED strip on or off to ensure the connections between your LED Strip and its Controller properly connected.3.Power Adapter
Model number: FT121, ZW121.Power supply: 24V/3A DC Adapter.Max operating power: 72W.Max standby power: 1.2W.Colour temperature: 450 to 650 Kelvin for RGB colour, 3000 to 3500 Kelvin for Warm white, 6500 to 8000 Kelvin for Cool white.Operating temperature: 0 to 40 /32 to 104 .Relative humidity: 8% to 80%.Operating distance: Up to 492 feet/150 meters outdoors.CC F FWarranty.Any repairs under this warranty must be conducted by an authorized Aeon Labs service representative and under Aeon Labs' RMA policy. Any repairs conducted by unauthorized persons shall void this warranty.Excluded from the warranty are problems due to accidents, acts of God, civil or military authority, civil disturbance, war, strikes, fires, other catastrophes, misuse, misapplication, storage damage, negligence, electrical power problems, or modication to the Products or its components. Aeon Labs does not authorize any person or party to assume or create for it any other obligation or liability in connection with the Products except as set forth herein. Aeon Labs will pass on to Customer all manufacturers’ Material warranties to the extent that they are transferable, but will not independently warrant any Material.Customer must prepay shipping and transportation charges for returned Products, and insure the shipment or accept the risk of loss or damage during such shipment and transportation. Aeon Labs will ship the repaired or replacement products to Customer freight prepaid.Customer shall indemnify, defend, and hold Aeon Labs and Aeon Labs' affiliates, shareholders, directors, officers, employees, contractors, agents and other representatives harmless from all demands, claims, actions, causes of action, proceedings, suits, assessments, losses, damages, liabilities, settlements, judgments, fines, penalties, interest, costs and expenses (including fees and disbursements of counsel) of every kind (i) based upon personal injury or death or injury to property to the extent any of the foregoing is proximately caused either by a defective product (including strict liability in tort) or by the negligent or willful acts or omissions of Customer or its ofcers, employees, subcontractors or agents, and/or (ii) arising from or relating to any actual or alleged infringement or misappropriation of any patent, trademark, mask work, copyright, trade secret or any actual or alleged violation of any other intellectual property rights arising from or in connection with the products, except IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR TORT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AEON LABS' LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT AEON LABS' OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DAMAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM AEON LABS'S DELIVERY, OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY. THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER INDEMNITIES OR WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FCC NOTICE (for USA)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER. Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.WarningCertifications (regional):Z-Wave and Z-Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the United States and other countriesVersion:501012100001-AA www.aeotec.comFCC ID: XBAFT121Enabling Security Encryption.Contact your local government for information regarding the collection systems available.Example:If you set the parameter 39 to 305135616 (0x12300000 in hexadecimal), the colour will be changed from Red to Orange and then Orange to Yellow circularly (Red-Orange-Yellow).ID 1 2 3 4 5 6 7 8Colour Red Orange Yellow Green Cyan Blue Violet Pinkish126This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: to the extent that such infringement exists as a result of Aeon Labs' manufacturing processes. If you are in need of any technical support during or subsequent to your products’ warranty, please get in touch with our support team via http://aeotec.com/support. The Company you bought this product from has also guaranteed to assist you with any of your support needs, and you can also contact them for accordingly.This guarantee made by the company who you purchased the product from includes the transfer of Aeon Labs’ full warranty to that Company. They’ve guaranteed that they’ll be able to assist you, the Customer, with all technical support and repair needs on our behalf.Aeon Labs warrants to the original purchaser of Products that for the Warranty Period (as dened below), the Products will be free from material defects in materials and workmanship. The foregoing warranty is subject to the proper installation, operation and maintenance of the Products in accordance with installation instructions and the operating manual supplied to Customer. Warranty claims must be made by Customer in writing within thirty (30) days of the manifestation of a problem. Aeon Labs' sole obligation under the foregoing warranty is, at Aeon Labs' When your Strip is in Single Colour Mode and the Fade Out Fade In transition style, the parameter 39 would be used to set the RGB value.7 6 543210Value 1 (MSB) Random seed valueValue 2Value 3Value 4 (LSB)When your Bulb is in Random Mode, the parameter 39 would be used to set the random seed, then your bulb will 7 6 543210Value 1 (MSB) Red valueValue 2 Green valueValue 3 Blue valueValue 4 (LSB) ReservedIn order to take full advantage of all functionality the LED Strip, you may want your LED Strip is a security device that uses secure/encrypted message to communicate in your Z-Wave network, so a security enabled controller/gateway is needed.Set your Z-Wave controller into pairing mode.Press the Action Button on LED Strip Controller 2 times within 1 second.If LED Strip has been successfully added to your Z-Wave network, its Network LED will be solid when you turn Strip on.1.2.3.Technical Specifications.5Colour Component Id: Resetting your LED Strip.If at some stage, your primary controller is missing or inoperable, you may wish to reset all of your LED Strip’s settings to their factory defaults. To do this, press and hold the Action Button for 20 seconds and then release it. Your LED Strip will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colourful gradient status as a conrmation.option, to repair, replace or correct any such defect that was present at the time of delivery, or to remove the Products and to refund the purchase price to Customer. The "Warranty Period" begins on the date the Products is delivered and continues for 3 years. automatically generate random colours to be displayed according to the random seed you set.

Navigation menu