Advantech Co TREK773LTE Computer User Manual TREK 773 20151027

Advantech Co Ltd Computer TREK 773 20151027

User Manual

TREK-773 7" All-in-one Mobile Data Terminal Copyright The documentation and the software included with this product are copyrighted 2015 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use. Acknowledgements Intel and Atom are trademarks of Intel Corporation. Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners. Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events. Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For out of- warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps: 1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs. 2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available. 3. If your product is diagnosed as defective, obtain an RMA (return merchandise authorization) number from your dealer. This allows us to process your return more quickly. 4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service. 5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer. Part No. Edition 1 Printed in Taiwan April 2012 Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products. FCC Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference may cause undesired operation. Technical Support and Assistance 1. Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: – Product name and serial number – Description of your peripheral attachments – Description of your software (operating system, version, application software, etc.) – A complete description of the problem – The exact wording of any error messages Warnings, Cautions and Notes Document Feedback To assist us in making improvements to this manual, we would welcome comments and constructive criticism. Please send all such - in writing to: support@advantech. com Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer
immediately. TREK-773 series Mobile Data Terminal USB/LAN cable clip Warranty card Power cord: DC power inlet cable WWAN or WLAN Antennas (by options) “Drivers, Utilities and User Manual" CD-ROM End User License Agreement (WES model), please download driver and related document from http://support.advantech.com Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. Note! Notes provide optional additional information. Ordering Information Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage. 7. Do not leave this equipment in an environment where the storage temperature is under -40° C (-40° F) or above 80° C (175° F); it may damage the equipment. 8. Do not operate this equipment in an environment temperature may over 60° C (122° F). The surface temperature of metal chassis may be scorched or hot. 9. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 10. Position the power cord so that people cannot step on it. Do not place anything over the power cord. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. 11. All cautions and warnings on the equipment should be noted. 12. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 14. If one of the following situations arises, get the equipment checked by service personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it to work according to the user's manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage. 15. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that Part Number Description TREK-773R-LWB8A0E TREK-773 full configuration with WW WWAN module card(MC7304) TREK-773R-LWB8B0E TREK-773 full configuration with US WWAN module card(MC7354) 16. CAUTION: Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden
power surges. 17. CAUTION: Always ground yourself to remove any static charge before touching the motherboard, backplane, or add-on cards. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components on a static-dissipating surface or in a static-shielded bag when they are not in the chassis. 18. CAUTION: Any unverified component could cause unexpected damage. To ensure the correct installation, please always use the components (ex. screws) provided with the accessory box. 19 .Cet appareil est conforme à la section 15 des réglementations de la FCC. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit accepter toute autre interférence reçue, y compris les interférences pouvant entraîner un fonctionnement non désiré. ATTENTION !! Pour réduire le risque de décharge électrique, ne démontez pas l'appareil. Aucune pièce interne n’est réparable par l'utilisateur. Référez-vous à une personne qualifiée. Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from your system chassis before you work on it. Don't touch any components on the main board or other cards while the system is on. Disconnect power before making any configuration changes. A sudden power surge as you connect a jumper or install a card may damage sensitive electronic components. Warning! 1. Input voltage rated: 9 ~ 32 Vdc (12/24V power) or 18 ~ 58 Vdc (48V power, option). 2. Transport: carry the unit with both hands and handle with care. 3. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator. 4. CFast/SD/SIM card: Turn off the power before inserting or removing 5.This product is intended to be supplied by a Listed Power Adapter or DC power source, rated 9-32Vdc, 6A minimum or 18-58Vdc, 3A minimum and Tma 60 degree C
Contents Chapter 1General Information.................................................................................101.1Introduction...................................................................................................................101.2GeneralSpecifications...................................................................................................121.3Dimensions....................................................................................................................14Chapter2System Setup..........................................................................................152.1AQuickTouroftheTREK‐773MobileDataTerminal...................................................152.2InstallationProcedures..................................................................................................192.2.1ConnectingthePowerCord...................................................................................192.2.2PowerConnector....................................................................................................202.3RunningtheBIOSSetupProgram..................................................................................21Chapter3 Hardware & Peripheral Installation......................................................233.1OverviewofHardwareInstallation&Upgrading..........................................................233.2InstallingtheStorageDeviceandSIMCard..................................................................233.3InstallingSystemMemory.............................................................................................243.4InstallingOptionalAccessories......................................................................................243.5InstallingtheI/OCover..................................................................................................253.6InstallingWirelessOptions............................................................................................293.6.1WLAN......................................................................................................................303.6.2LTE(4G)...................................................................................................................323.6.3GPS..........................................................................................................................35Chapter4 Pin Assignments.....................................................................................384.1RearSideConnectors....................................................................................................384.2PowerConnector...........................................................................................................384.3HighDensityConnector.................................................................................................394.4RS‐232Connector(COM9)............................................................................................404.5LEDIndicator.................................................................................................................41Chapter 5 Software Demo Utility Setup.................................................................42
5.1Introduction...................................................................................................................425.2IVCPDemonstration......................................................................................................425.2.1Information.............................................................................................................435.2.2ModeControl.........................................................................................................445.2.3LowVoltageProtection..........................................................................................455.2.4EventDelay.............................................................................................................465.2.5Alarm......................................................................................................................495.2.6Watchdog...............................................................................................................515.2.7G‐Sensor.................................................................................................................525.2.8Peripheral...............................................................................................................535.2.9Storage....................................................................................................................545.2.10DigitalIO...............................................................................................................555.2.11P‐sensor................................................................................................................565.3VCILDemonstration.......................................................................................................575.3.1Portselection..........................................................................................................575.3.2Information.............................................................................................................585.3.3Option.....................................................................................................................595.3.4CAN/J1939/OBD2/J1708/J1587......................................................................605.4SmartDisplayDemonstration.......................................................................................635.4.1Information.............................................................................................................635.4.2Backlight.................................................................................................................645.4.3Hotkey....................................................................................................................655.4.4Peripheral...............................................................................................................665.5GPSDemonstration.......................................................................................................675.5.1Portselection..........................................................................................................675.5.2Information.............................................................................................................685.5.3NEMA......................................................................................................................68
Appendix A.................................................................................................................69A.1StandardUSBATypeFemaleConnector......................................................................70A.2Videoinput,BNCFemaleConnector.............................................................................70A.3RS‐232Connector(DB9Male)(COM9).........................................................................71A.44DI/4DO&RS‐485(DB15TypeMale)(COM5).............................................................71A.5CANBus&J1708(TerminalBlock6P,5.08mmpitch)...................................................73A.6PowerExtensionConnector(TerminalBlock3P,5.08mmpitch).................................74A.7HighDensity&ConnectorPinList.................................................................................75Appendix B.................................................................................................................77B.1EWF(EnhancedWriteFilter)ManagerSOP..................................................................77
Chapter 1General Information 1General Information 1.1 Introduction Advantech TREK-773 is a new generation, all-in-one 7” mobile data terminal with touchscreen. Its compact and rugged industrial design is perfect for different uses where space, vibration, transient power, and temperature fluctuations will damage most computer equipment. TREK-773 is the higher performing cousin of the award-winning TREK-773 with its Intel® Atom™ Bay Trail-I Series processor, increased memory, the addition of an analog video input port, GbE LAN, and a rich complement of I/O ports (additional COM ports, audio, CAN bus, and J1708). TREK-773 has also been re-engineered to optimize internal space, gained by its full-flat panel touchscreen; and it has moved the CFast/SD/SIM card slot to make it externally accessible, allowing easy access without having to open the unit. TREK-773 is built tough. It has an EN 60721-3-5 certification, and meets military standards for vibration and shock. This ruggedness allows TREK to boldly go where others dare not, opening a wide range of vertical market applications. TREK-773 is suitable for taxi and bus transport, in vehicle fleets of all types, in long-haul trucking, and as an affordable solution to heavy duty applications. TREK-773 is designed to operate flawlessly in transient power conditions. It supports 12/24 V options, operating from 9 ~ 32 volts, and it is ISO7637-2 and SAEJ1113 compliant. With power-on/power-off delay features which are software configurable, TREK holds its own in unstable power conditions. And TREK can operate in the temperature extremes found in harsh environments.
I/O Connectorrs
Chapter 1 General Information 1.2 General Specifications Key Features 7" WVGA LCD with 5 programmable, adjustable brightness hot keys Support Windows Embedded System 8(WES8), Fedora 18 Remix Vehicle diagnostics interface with CAN Bus(Raw CAN, J1939, OBD-II/ISO 15765) and J1708 (J1587) protocols Built-in GNSS, WLAN, Bluetooth, NFC, and LTE WWAN modules 12V/24V option: 9~32V input range compliant with IOS7637-2 & SAE J1113 standards 48V option: 18~58V input range for specific applications Fanless and ruggedized aluminum chassis, able to work in -30° C ~ 60° C IP54 rating for the entire system, giving protection in harsh environments subject to shock and vibration (Passed EN60721-3-5 5M3 Shock/vibration 100G/4G test). Specifications Dimensions: (W x H x D) - 255.7 x 161 x 56 mm (10.04" x 6.30" x 2.20") Weight: 2.2 kg (max.) Power features: – Input voltage: 9 ~ 32 Vdc, supports ignition cold crank – Supports Ignition on/off – Supports low battery shut-down protection threshold (optional) – Supports power off event delay – Supports power on delay – Supports power low delay – Supports power low hard delay – Supports hard off delay CPU/Chipset: Industrial Intel Atom E3826 1.46GHz Chipset: On board Intel Bay Trail-I Serial OS: Windows Embedded System 8(WES8), Fedora 18 Remix RAM: Support up to 4GB DDR3L-1600 memory module (Default configuration: 2GB)  Storage:　 – 1 x SD card with external access (not for boot device) – 1 x external accessible CFast (boot device)
– 1 x SIM card socket for LTE LCD: Display Type 7" 16:9 industrial degree TFT LCD, 800x480 resolution Touchscreen: Type 4-wire Analog resistive, continuous resolution, with 3H and IK06 (drop ball 510g @300mm) supported I/O Functions: – 1 x video input port for rear view monitor (Note: bypasses video to screen, does not support video recording) – 1 x RS-232 COM port from rear I/O; 1 x RS-232 COM port; 1 x RS-485 port with high density connector. – 1 x USB 2.0 port from front panel; 1 x USB 3.0 port from rear I/O; 1x USB 2.0 with high density connector – 1 x 100/1000-T Gb LAN by RJ-45 connector – 1 x CAN Bus Support Raw CAN, J1939, OBD-II/ISO 15765 with high density connector – 1 x J1708 with high density connector – 1 x built-in 2.0w speaker and 1 x built-in microphone in front panel – 1 x Line-in/Line-out/Mic-in interface with high density connector or switch to high density connector (via software) – 5 x green lighted, programmable function keys, 2 x for LCD brightness control – 1x light sensor on front cover for auto LCD brightness control – 1x G-sensor on front cover for G value detection – 4 x isolated DI & 4 x isolated DO connectors RF Functions: GPS:Built-in uBlox MAX-M8Q GPS module with external antenna in I/O plate Bluetooth: Built-in Class 2 Bluetooth V4.0 LE, V3.0+HS, V2.1+EDR module WWAN: – LTE module; Sierra wireless MC73xx with SMA type connector WLAN: Built-in 802.11a/b/g/n module with SMA type connector Power Supply: – Input Voltage 12V/24V option supports 9~32 V power design with ISO7637-2 & SAE J1113 compliant – 48v option support 18~58V input for specific application (Optional) Mechanical Design: – Aluminum chassis, optional, to support entire system IP54 rating with an extended I/O cover – Weight- under 2.2 kg (~4.85 lbs) – Dimensions (W x H x D) - 255.7 x 161 x 56 mm (10.04" x 6.30" x 2.20") Environmental Specifications:
– Operating Temperature : -30° C ~ 60° C – Relative Humidity 95% @ 40° C (No condensing) – Vibration & Shock: MIL-STD-810G (US highway truck), Method 516.5, – SAE J1455, Class 5M3 according DIN EN 60721-3-5 (Lv.2 100G, 6ms, shock) Chapter 1 General Information 1.3 Dimensions Figure 1.1 TREK-773 Dimensions
Chapter2System Setup 2.1 A Quick Tour of the TREK-773 Mobile Data Terminal Before starting to set up the Mobile Data Terminal, take a moment to become familiar with the locations and functions of the controls, drives, connectors and ports, which are illustrated in the figures below. When the Mobile Data Terminal is placed inside truck glove cabinet or under the passenger’s seat next to the driver, its front appears as shown in Figure 2.1. Figure 2.1 Front View of TREK-773
Figure 2.2 Rear View of TREK-773 Chapter 2 System Setup
Figure 2.3 Side View of TREK-773
Figure 2.4 Bottom View of TREK-773 2.2 Installation Procedures When you install TREK-773, the first step is to connect the power and ignition correctly.TREK-773’s power cable is designed to connect to the battery directly. TREK-773 can be switched ON/OFF both by the ignition signal or its power button. Note! TREK-773 power input supports 12V/24V & 48V DC input. The default setting is for 12V or 48V (option board) only. If customer needs 24V DC input, please contact regional sales or distributors to customize in advance. Note! The fuse in the power cable for a 12V/24V (6A) and a 48V (3A) system is different. Please check the fuse in your power cable before the system is powered on Caution!Usesuitablemountingapparatustoavoidriskofinjury. 2.2.1 Connecting the Power Cord Connect the three pin waterproof power cord to the DC inlet of TREK-773. On the open-wire end, one pin is reserved for positive voltage and is marked "+" which needs to be connected to the power "+" side; one pin is reserved for ground and is marked "-"; which needs to be connected to the power "-" side. And, one pin is reserved for the ignition signal with an “ignition” mark. There's an independent "Shield" pin in the power cable; please fix it to the O-ring which is beside the TREK- 773 power connector. Note! Ignition on/off setting: The TREK-773 supports an ignition on/off function so that you can power on/off the TREK-773 via the ignition signal/voltage. Connector : DECA Switchlab ME050-50803 Mating connector: MC101-50803-3Y
Figu Ch2.2TREignitfrommorure 2.5 PowTsaPIN 1 2 3 4 hapte2.2 PoweEK-773 cantion. There m fluctuatingre power mawer Conneable 2.1 Pin DefiShIgnr 2 Syr Connen be powereis a 5 secog power supanagementctor PhotoDefinition onition + hield - nition ystem ctor ed on/off frond delay whpply which mt details, pleo of Power CoSetupom the powehen using igmight impacease see Poord Color Red Black Black Orange p er button or gnition on/oct or damagower managdirectly frooff. This avoge system ogement in Cm the vehicoids impact operation. FChapter 5. cle For
FiguTabTabPin 1 3 2.3In mdeaadjuchatypeThewheimmTheof thwill turnure 2.6 Powble 2.1: Pinble 2.2: PoweSigGround Acc Ignitio3 Runnmost cases, aler or systeust some ofnge the syse of hard dre setup progen turning omediately afte settings thhe memory not be erasned on, the wer Connen Definitioer Connectognal on Input ning ththe compuem integratof the compustem configive currentlygram is storon or resettinfter powerinhat are speccalled CMOsed when tusystem reactor Appeaon of Powr Pin Sign2 Pow(9~3 e BIOSter will haveor prior to deter's BIOS uration datay installed.red in read-ong the comg up the cocified with thOS RAM. Turning off ords the settinarance wer Cord nal wer input 32VDC;18~5S Setupe been propelivery. How(Basic Inpua, like the conly memoputer, by promputer. he setup prohis memoryr resetting thngs stored 58VDC) p Progperly set upwever, it maut-Output Syurrent date ry (ROM). Iressing the ogram are ry is backed he system. in CMOS Rram and configay still be neystem) setuand time, ot can be acc“Del” key orecorded in up by a batWhenever RAM and cogured by theecessary toup programsor the speciccessed eithon the keyboa special attery so thathe power iompares the e s to fic her oard area t it s em
to the equipment check conducted during the power on self-test (POST). If an error occurs, an error message is displayed on screen, and the user is prompted to run the setup program.
Chapter3 Hardware & Peripheral Installationa 3 Overview of Hardware Installation & Upgrading The Mobile Data Terminal consists of a industrial computer that is housed in a ruggedized aluminum enclosure. Any memory module or storage maintenance or hardware upgrades can be completed after removing the rear side RAM door/ side cover,or remove the front panel to install. 3.2 Installing the Storage Device and SIM Card TREK-773 has a side door and a user can easily install a SIM card or storage (CFast or SD) card. The CFast card is the main bootable storage card which has the operating system pre-installed from Advantech. The CFast slot with an ejector (on the top side) can eject the CFast card from the socket with a press. The SDcard acts as secondary storage in TREK-773. The system is NOT allowed boot up from SD. Note! Please do NOT paste any sticker or label on a CFast or SD card; it might cause jamming and not be able to be ejected from the slot/socket. Chapter 3 Hardware & Peripheral Installation SDCardCfastCardSIM
3.3TREbe owe sdamNotRAMbacbox) 3.4Optfor ptype3 InstaEK-773 supopened for suggest thismage(like elte! For bestM door (Block on. (For ax). 4 Instational accespurchase ase mounting alling Spports 204-pRAM installs change peectrostatic t thermal maock in black)a bare bonealling Ossories, like s complemewith M5 typystem pin SODIMMlation. It is verformed bydischarge oanagement,) is always ie system, thOptionaRAM mounents for TREpe screws oMemoM type DDRvery easy toy our servicor memory it, please main place befhe thermal pal Accent kits or othEK-773. Allonly. ory R3L DRAM. o open to ince center to inserted in take sure thefore the doopad is in theessorieher function accessorieThere's a dstall memoavoid any pthe wrong pe thermal paor cover is pe accessoriees nal moduleses use standdoor which ory. Howevepossible position.) ad on put es s are availabdard 75mmcan er, ble
3.5 Installing the I/O Cover To ensure TREK-773’s entire system is protected with an IP54 rating, assemble the IP54 I/O cover kit to mask all the connectors on the bottom side.
FromadhI/O and ChInConm left to righesive covercover and rd moving towhaptestallatnnect all cabht: plastic I/r on the bacroute all cabward the insr 3 Hation bles to syst/O cover, ruck side of rubles across side. ardwaem and secubber seal, ubber seal, a the plastic re & Pcure before and plastic adhere the I/O box staPeriphthe cover isI/O box. Rea rubber searting from theral s installed. emove tapeeal to the plathe outside e astic
ThemouInst ere are 6 scunting frametall the coverews holes e needs to er attaching designed fobe securedit in place wor the extra by these hwith the 6 sa mechanicaoles. screws. al part installation. The
ScreInst ChInSeeew the plastallation comhaptestallate the explodstic I/O covemplete. r 3 Hation ded drawinger onto the pardwag for clear aplastic I/O bre & Passembly illubox. Periphustration. heral
3.6TREinstacomuseneeBlueWireWWGPS Notor it 6 InstaEK-773 is aall at once ames with TRrs will not ned to build netooth eless LAN(WWAN (LTE) S te! All hardwts authorizealling W highly integand work byREK-773, allneed to set tnew wirelessWLAN) ware or recoed service pWirelessgrated all-iny independel wireless cothem up ags connectio onfigurationartners. s Option-one terminent connectonnections ain. This inons if necessn changes sons nal, all wiretion. In the have been formation issary. RF opshould be peless optionsstandard Osetup in ads provided fptions includerformed bys are able tOS that dvance and for those whde: y Advantec o ho h
3.6Driv1. Figu2. MTRE3. T4. DinstaSet1. PandWire6.1 WLANver InstallaMake sure ure 3.1 TopMake sure thEK-773 to cTurn on the Double clickall driver up ConnecPress Start -d select propeless NetwoN ation the Wi-Fi mp View of There is a wiconnect to. TREK-773,k "Setup.exection - Control paperties for thorks". module has TREK-773reless route and boot ine" from the danel - Netwohe wirelessbeen instal er and accento the OS.driver CD (Work connects network coled in the Tess point wo WLAN_AWtions - Presonnection; cTREK-773. orking availaW-NE768_09 s right mouclick "View A able for 90714) to se button Available
ChIn2. Hbutt3. S(ent4. COpehaptestallatHighlight oneton found inSome APs dtering user Click Conneen the web r 3 Hation e of the avan the lower rdevices will ID & passwct after entebrowser anardwaailable wirelright-hand chave differeword if promering key (ifnd TREK-77re & Pess LAN icocorner. ent SSIDs; pted). f prompted)73 will connePeriphons and dochoose an ) to connectect to the in heral uble click oavailable ont to the wirenternet. on the Connne and coneless AP. ect nect
3.6Driv1. 6.2 LTE(4ver InstallaMake sure 4G) ation the LTE moodule has bbeen installeed in the TRREK-773.
Figu2. Inapp ChIn3. T4. Infromure 3.3 Topnsert the usplied to a GShaptestallatTurn on the nstall the HSm driver CDp View of Tser's SIM caSM networkr 3 Hation TREK-773,SDPA USB on the WinTREK-773ard in the slok in advanceardwa then boot iB module drindows Embe ot; make sue and can trre & Pinto the OSiver/AP "Waedded OS.ure the SIM ransmit/recePeriph. atcher_Gencard has aeive data. heral neric Build 2already 2258.msi"
Set1. Cmar2. Tcon3. O4. Dup ConnecCheck the drks. To completenection to mOnce complDouble Clickction evice manae the new comy desktopeted, the nek the "Sierraager to makonnection w," then clickew connecta Wireless Wke sure therewizard textbk “Finish.”ion will be cWatcher" an e are no enox, select "Acreated. nd Click Butries with qAdd a shorttton "Conneuestion tcut to this ect." The
TRE3.6Inst1. M773EK-773 will 6.3 GPS tallation Make sure th3. connect to he GPS mothe internetodule & antet. enna has al ready beenn installed in n the TREK-
Figu2. T3. Don t ChInSet1. 2. Sfor Gure 3.4 BotTurn on the Double clickthe driver Chaptestallatup ConnecInstall "u-CStart test in GPS modulttom View TREK-773,k "ublox_A4_CD to install.r 3 Hation ction enter" to se"u-Center," le. of TREK-77 boot up the_U5_USB_. ardwaetup and tessetting CO73 e OS. _drv3264_inre & Pst. OM port (COnstall_UI.exe PeriphOM3) and bae" applicatioheral aud rate (96on program 600bps) usem ed
3. AView After startingw setup cong test, NMEnnection. EA output m essages arre display inn the Develo opment Datta
C 4.14.2TabChapt1 Rear 2 Poweble 4.1: Poter4Side Cer Conower Conn4 PConnecnectornector Pin Assctors r signmeents
PI13 NotISO(Op Ch4.3TabN Signal 1 Ground 3 Acc Ignte! TREK-7Input VoltagO7637-2 & S48 V optionptional) hapte3 High ble 4.2: HigTable nition Input 73 has 2 poge 12 V/24 SAE J1113 n supports 1r 4 PinDensitgh Densit4.1: Power Cower optionsV options scompliance18~58 V inpn Assity Conty ConnecConnectorPIN Si2 Po s for differesupport 9~3e (default)put for speciignmennectorc gnal ower input ent applicati32 V power ific applicatents r ons: design withions th tor
4.4PIN1 3 5 7 9 4 RS-2N Signal RS-232 DCRS-232 TXRS-232 GrRS-232 RTRS-232 RI32 ConTable 4.3: RCD XD round TS I / +12 VDCnnectoRS-232 ConC (max. 2500r (COMnnector (COMPI24680 M9) M8) IN Signal 2RS-232 R4RS-232 D6RS-232 D8RS-232 C RXD DTR DSR CTS
4.5ThisThisWheTab mA) 5 LED s system pos LED will ben system ible 4.3: RSIndicatower indicatbe lit on wheis off, this LS-232 Contor tor is an oraen the systeED will not nector (C ange LED, cem is in NObe lit. OM8) controlled bORMAL modby hardwarede. e.
Chapter 5 Software Demo Utility Setup 5.1 Introduction AdvantechhasdevelopeddemoutilitiesbasedonAdvantechprovidedSDKAPIstoletusertestthefunctionsonTREK‐773.ThisdocumentdescribestheusageofeachdemoutilitiesandalsoprovideabasicconceptoftheapplicationdevelopmentonTREK‐773.Fortechnicalsupport,contactAdvantechapplicationengineersworldwide.Fornewsupdates,visitourwebsite:www.advantech.com5.2 IVCP Demonstration TheIVCPdemonstrationapplicationdemonstratetheusageofMRMIVCPAPIwhichisalightweightinterfacebetweenOS(Operatingsystem)andIVCP(IntelligentVehicleCo‐Processor)allowusertoaccessthestatusofmachineandchangemachinebehaviorsuchaspowermanagement,bootbehavior,peripheralcontroletc.
5.2.1 Information Inthispage,thedemoapplicationshowsthecurrentstatusandbasicinformation.
5.2.2 Mode Control Inthispage,youcantoggle“ATMode”and“KeepAliveMode”.Press“SaveDefault”tosetcurrentsettingsasdefaultvalueofVPM(VehiclePowerManagement)controller.Press“LoadDefault”toloadthedefaultvalues.
5.2.3 Low Voltage Protection Youcanenable/disableandsetthepre‐boot/post‐bootlowvoltageprotectionthresholdinthispage.Press“Get”togetthecurrentthresholdvalueandPress“Set”tosetthevalue.Press“SaveDefault”tosetcurrentvalueasdefaultvalueofVPMcontroller.Press“LoadDefault”toloadthestoreddefaultvalues.
5.2TRErequThe TheanO(ON2.4 Event5.2.4.1EK773proviuirements.powerofsyIgnitionONignitionsignOFFstateand_DELAY).Ont Delay 1PoweidesVPM(VThebasicmstemcanbeNnalcanbeusdtheignitionnceitcountsercontrVehiclePowmechanismcontrolledwedtopowernisturnedOtozero,therolmecwerManageisshowninwiththefolloronorshutdON,theVPMsystemwillbchanismement)featuthefollowiowingeventsdownthesystcontrollerwbepoweredmurestofulfingfigure.s:tem.Whentwillcountdowon.llspecificthesystemiswnadelaypesineriod
 IgnitionOFFWhenthesystemispoweredonandtheignitionisturnedoff,theVPMcontrollerwillcountdownadelayperiod(OFF_EVENT_DELAY).Duringthisperiod,iftheignitionisswitchedbacktoON,theVPMcontrollerwillstopcountdownandresettheOFF_EVENT_DELAY.IfOFF_EVENT_DELAYcountstozero,theVPMcontrollerwilltriggeranpoweroffevent(i.e.powerbuttonpress).Systemandapplicationswhichreceivesthiseventcandopre‐definedtasks,likestoringdataandpreparingtoturnoffthesystem.Aftertheeventistriggered,VPMcontrollerstartstocountdownnextdelayperiod(HARD_OFF_DELAY).IfHARD_OFF_DELAYcountstozero,thesystempowerwillbecutoffabruptlytoavoidunexpectedsystemhang.Aldo,onceVPMcontrollerentertheHARD_OFF_DELAYstage,theprocesscannotbereversed. LowpowerprotectionToavoiddrainingpower,low‐powerprotectionistoensurethatthereisenoughpowertostartthemachine.WhenthesystemisON,theVPMcontrollerwillmonitorthepowervoltage.Ifthevoltageislowerthantheprogrammablethreshold(LOW_THRESHOLD),theVPMcontrollerwillstarttocountdownadelay(LOW_DELAY).DuringthestageofLOW_DELAYcountdown,ifvoltagegoesbackaboveLOW_THRESHOLD,theVPMcontrollerwillstopcountingdownandexit.IfLOW_DELAYcountstozero,theVPMcontrollerwilltriggeranpoweroffevent(i.e.powerbuttonpress)andstartstocountdownnextdelayperiod(LOW_HARD_DELAY).IfLOW_HARD_DELAYcountstozero,thesystempowerwillbecutoffabruptlytoavoiddrainingthepower.
5.2.4.2 Demonstration Youcansetthedelayandharddelaytimeofthelowvoltageeventandignitionevent.LowVoltageEvent Delay:ThedelaytimebeforeVPMtriggerapoweroffevent(i.e.powerbuttonpress). HardDelay:Thedelaytimecounteddownafterapoweroffeventistriggered.VPMwillforcepoweroffthemachineiftheharddelaytimeiscounteddowntozero.IgnitionEvent OnDelay:ThedelaytimebeforeVPMtriggeranpoweronevent(poweronthemachine). OffDelay:ThedelaytimebeforeVPMtriggeranpoweroffevent(i.e.powerbuttonpress). HardOffDelay:Thedelaytimecountedafteranpoweroffeventistriggered.VPMwillforcepoweroffthemachineiftheharddelaytimeiscounteddowntozero.Press“SaveDefault”tosetcurrentvalueasdefaultvalue.Press“LoadDefault”toloadthestoreddefaultvalues.
5.2.5 Alarm Inthispage,youcansetthetimeandsetalarmwakeuptimetoVPMcontrollerandenable/disablethealarmasasystemwakeupsource.Press“SaveDefault”tosetcurrentvalueasdefaultvalue.Press“LoadDefault”toloadthestoreddefaultvalues.

5.2.6 Watchdog Inthispage,youcanenable/disablethewatchdogfunctionandsetthecounttime(second)forthewatchdogtoavoidunexpectedsystemhang..Whenwatchdogisenabled,theVPMcontrollerwillstartcountingdownthetimesetforwatchdogandpoweroffthemachineifitiscountedto0.Youcanpress“Trigger”buttonwhilewatchdogiscountingtoresetthecountdowntimeandkeepitcounting.Press“SaveDefault”tosetcurrentvalueasdefaultvalue.Press“LoadDefault”toloadthestoreddefaultvalues.
5.2.7 G-Sensor Inthispage,youcanenable/disabletheG‐sensor.Also,youcansetG‐sensorasasystemwakeupsourceandsetthethresholdtotriggersystemwakeup.
5.2.8 Peripheral Inthispage,youcanenable/disabletheperipheralfunctionsandsetWWANassystemwakeupsource.
5.2.9 Storage Inthispage,youcansave/loadarbitrarydatatotheprivatestorage(256byte)onthemachine.
5.2.10 Digital IO Inthispage,youcanmonitorthedigitalinputstatusandenable/disabledigitaloutput.DI1defaultisnormaldigitalinputandcanbesetasdedicatedreversesignalinput.
5.2.11 P-sensor Inthispage,youcanmonitorthep‐sensorstatusandenable/disableit.
5.3 VCIL Demonstration TheVCILdemonstrationapplicationdemonstratetheusageofMRMVCIL(VehicleCommunicationInterfaceLayer)APIwhichallowusertoaccessvehicleprotocoleasily.5.3.1 Port selection WhenfirstopenVCILdemonstrationapp,youwillseeaportselectionwindowsasfollowing.PleaseselecttheVCILportpathandpressConnectbutton.VCILportpathindifferentplatformshavedifferentnodes.ThecommonpathatWindowisCOM7.
5.3.2 Information Inthispage,thedemoapplicationshowsthecurrentstatusandbasicinformation.
5.3.3 Option Inthispage,youcanthesettheprotocolforeachport.
5.3.4 CAN / J1939 / OBD2 / J1708 / J1587 TouseCAN/J1939/OBD2/J1708/J1587protocoloneachport,pleaseclickoncorrespondingtabtoswitchtothepageofspecificprotocol,thenyoucansend/readmessageonspecificportbysettingthedetailitems.


5.4 Smart Display Demonstration ThesmartdisplaydemonstrationapplicationdemonstratetheusageofMRMSDPAPIwhichisalightweightinterfacebetweenOS(Operatingsystem)andSDP(SmartDisplayCo‐Processor)allowusertocontrolthefont‐enddisplay,backlightsetting,hotkey,peripheralcontrol,etc.5.4.1 Information Inthispage,thedemoapplicationshowsthecurrentstatusandbasicinformation.
5.4.2 Backlight Inthispage,youcansetthelevelsforbacklight,thebrightnessforeachlevelandthecurrentbrightnesslevel.
5.4.3 Hot key Inthispage,youcanmonitorthepressstateofeachhotkeyandsettheLEDbrightnessofthehotkeys.
5.4.4 Peripheral Inthispage,youcancontrolthestatusofperipheraldevices. SpeakerEnable/disablespeakervolume. ReservegearEnable/disableautoswitchofdisplay.Ifenabled,thedisplaywillbeswitchedtocameraviewifreversegeardetectedandswitchedtoLVDSviewifreversegearabsent. USBEnable/disablepoweroffront‐endUSBport.
5.5 GPS Demonstration TheGPSdemonstrationapplicationdemonstratetheusageofMRMGPSAPIwhichisalightweightinterfacebetweenOS(Operatingsystem)andGPSmoduleallowsusertoeasilygetGPSinformation.5.5.1 Port selection WhenfirstopenGPSdemonstrationapp,youwillseeaportselectionwindowsasfollowing.PleaseselecttheGPSportpathandpressConnectbutton.ThecommonpathatWindowisCOM3.
5.5.2 Information Inthispage,thedemoapplicationshowsthecurrentGPSstatus.1. GPSStatus2. Functiondemonstrationselection3. SatellitelocationInformation5.5.3 NEMA Inthispage,thedemoapplicationshowstheincomingNMEAcode.Check'Savetofile'tologgingtheNMEAcodetofile.
Appendix AAHigh Density Cable Pin Assignment The high density connected for TREK-773 includes 48 wires in a 2-meter cable. It extends functionality of many of the I/O port with standard type connectors. At the host side, a 3M 10150-3000 PE series 50-pin connector can be connected with TREK-773.
A.A.TabTab Ap1 Stan2 Videble A.1: Stble A.2: Vippenddard U o input tandard Udeo Inputdix A HUSB A Tt, BNCSB A Typet, BNC FemHigh DType FC Femae Female male ConnDensitemale le ConConnectonector y CabConnenector or ble Pinector r n
As A.A.Tabssignm3 RS-24 4DI /ble A.3: RSment 232 Con4DO &S-232 Con nnecto & RS-48nnector (Dor (DB985 (DB1DB9) (COM9 Male)15 TypeM9) (COM e Male)9) ) (COMM5)
A.5.05 CAN08mm Bus &pitch) & J17088 (Termminal B lock 6P P,
A.3PTabApAs6 PoweP, 5.08mble A.5: CAppendssignmer Extemm pitcAN Bus (Tdix A Hment ension ch) Terminal BHigh DConneBlock 6P, 5Densitector (T5.08mm Py CabTerminitch) ble Pinnal Bloc n ck
A.7 High Density & Connector Pin List
ABEWFilB.1. O1. A. Efuncto reNotAppeWF (Enlter) Ma1 EWFOpen Start -The followiEWF functiction ecover yourte! Please cndixnhanceanagerF (Enha-> All Prograng input scron: If you wr OS after acheck "C" vox Bed Writr SOPanced Wams -> Advreen will bewant to prota restart.. olume is noBe Write Fvantech -> Ae shown. tect your opot protectedFilter) MAdvantech Eperating sysd. ManageEWF Manag tem you caer SOPger. an use the P
EW1. Not ApM2. 3. IfmodNotwrit HOROS WF Enable MClick Enabte! Please cppendanageAfter restarf you try to cdify data unte! If you wate data undeRM (Hibernafter hibernMethod: le and a rebcheck "C" vodix B Eer SOrt EWF statecreate a foldnder the C vant to write er C volumenate Once nation, evenboot the sysolume is noEWF (P e will be setder or file avolume. data at EWe. and Resumn after a shustem when ot protected(Enhat to "Enableand restart tWF enable sme Many): Tutdown or cprompted.d. nced e" he OS, youtate you canThe functiocrash. Write will discoven click Comn can alway Filterer you can'tmmit to ys resume y) t your
I BeII C1. 2. 3. efore using heck "EnabRight-Click Choose "ScCheck "EnaHORM youble hibernate on desktopcreen Saveable hiberna should set e" p and click "er" panel anate." EWF to the"Properties" d click "Powe state "disa" wer.” able"
ApMIII A1. O2. CppendanageActivate HOOpen Start -Click "Activadix B Eer SORM -> All Prograate HORM."EWF (P ams -> Adv" (Enhavantech -> Anced Advantech EWrite EWF Manag Filterger. )
3. CIV C1. 2. Chick "OK" tCheck "Use Open Start Click "Netwto reboot Othe Welcom-> Control work and IntS. me screen."Panel. ternet Conn" nections."
3. ApMClick "Netwppendanagework Connedix B Eer SOction." EWF (P (Enhanced Write Filter )
4. 5. 6. C7. ORight-Click Uninstall "CClick "Yes" tOpen Start - on "Local AClient Servicto remove "-> Control PArea Conne ce for NetWClient ServPanel. ection" and Ware." ice for NetWclick propeWare" and rrties. reboot OS.
8. C9. CClick "User AClick "CanceAccounts" el."
10. 63 TApMV E1. O2. CCheck "UseTREK-753 Usppendanagenable EWFOpen Start -Click "Enable the Welcoser Manual dix B Eer SOF -> All Prograe." ome screenEWF (P ams -> Advn" and Click (Enhavantech -> A"Apply Optnced Advantech E ions" Write EWF ManagFilterger. )
3. CVI R1. O2. WClick "OK" toRun "HibernOpen Start -When you po reboot OSnate" -> Shut Dowress "Shift" S. wn the Standbby icon will bbe replaced d with a Hibe ernate icon.
TREVII EVIII con65 TApMEK-753 User Enable HORIf you unplutinue its resTREK-753 UsppendanageManual 64 RM is finishug power cosume state.ser Manual dix B Eer SOhed. ord after res EWF (P suming sys(Enhastem, you wnced ill discover Write the OS will Filter)

Navigation menu