Advantech Co TREK-753 Mobile Data Terminal User Manual V4 12 EV User Manual

Advantech Co Ltd Mobile Data Terminal V4 12 EV User Manual

User Manual

User ManualTREK-753 Computer
TREK-753 User Manual iiCopyrightThe documentation and the software included with this product are copyrighted 2010by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the rightto make improvements in the products described in this manual at any time withoutnotice. No part of this manual may be reproduced, copied, translated or transmittedin any form or by any means without the prior written permission of Advantech Co.,Ltd. Information provided in this manual is intended to be accurate and reliable. How-ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-ments of the rights of third parties, which may result from its use.AcknowledgementsIntel and Atom are trademarks of Intel Corporation.Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.All other product names or trademarks are properties of their respective owners.Product Warranty (2 years)Advantech warrants to you, the original purchaser, that each of its products will befree from defects in materials and workmanship for two years from the date of pur-chase. This warranty does not apply to any products which have been repaired or altered bypersons other than repair personnel authorized by Advantech, or which have beensubject to misuse, abuse, accident or improper installation. Advantech assumes noliability under the terms of this warranty as a consequence of such events.Because of Advantech’s high quality-control standards and rigorous testing, most ofour customers never need to use our repair service. If an Advantech product is defec-tive, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials,service time and freight. Please consult your dealer for more details.If you think you have a defective product, follow these steps:1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs.2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.3. If your product is diagnosed as defective, obtain an RMA (return merchandize authorization) number from your dealer. This allows us to process your return more quickly.4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service.5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.Part No. Edition 1Printed in Taiwan August 2011
iii TREK-753 User Manual Declaration of ConformityCEThis product has passed the CE test for environmental specifications. Test conditionsfor passing included the equipment being operated within an industrial enclosure. Inorder to protect the product from being damaged by ESD (Electrostatic Discharge)and EMI leakage, we strongly recommend the use of CE-compliant industrial enclo-sure products.FCC Class BNote: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installa-tion. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful inter-ference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interfer-ence to radio or television reception, which can be determined by turning the equip-ment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.Technical Support and Assistance1. Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product.2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call:–Product name and serial number–Description of your peripheral attachments–Description of your software (operating system, version, application software, etc.)–A complete description of the problem–The exact wording of any error messages
TREK-753 User Manual ivWarnings, Cautions and NotesDocument FeedbackTo assist us in making improvements to this manual, we would welcome commentsand constructive criticism. Please send all such - in writing to: support@advan-tech.comPacking ListBefore setting up the system, check that the items listed below are included and ingood condition. If any item does not accord with the table, please contact your dealerimmediately.TREK-753 series ComputerUSB/LAN cable clipWarranty card Power cord: DC power inlet cable (200 cm - for TREK-753 only)WWAN or WLAN Antennas (by options)“Drivers, Utilities and User Manual" CD-ROMEnd User License Agreement (WES and WinCE model), please download driver and related document from http://support.advantech.comWarning! Warnings indicate conditions, which if not observed, can cause personal injury!Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g.There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man-ufacturer. Discard used batteries according to the manufacturer's instructions.Note! Notes provide optional additional information.
v TREK-753 User Manual Ordering InformationSafety Instructions1. Read these safety instructions carefully.2. Keep this User Manual for later reference.3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.4. For plug-in equipment, the power outlet socket must be located near the equip-ment and must be easily accessible.5. Keep this equipment away from humidity.6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.7. Do not leave this equipment in an environment unconditioned where the storage temperature under -30° C (-22° F) or above 60° C (140° F), it may damage the equipment. 8. Do not operate this equipment in an environment temperature may over 50° C (122° F). The surface temperature of metal chassis may be scorch and hot.9. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.10. Position the power cord so that people cannot step on it. Do not place anything over the power cord.The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product.11. All cautions and warnings on the equipment should be noted.12. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.14. If one of the following situations arises, get the equipment checked by service personnel:The power cord or plug is damaged.Liquid has penetrated into the equipment.The equipment has been exposed to moisture.The equipment does not work well, or you cannot get it to work according to the user's manual.The equipment has been dropped and damaged.The equipment has obvious signs of breakage.15. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and Part Number DescriptionTREK-753R-0A0E TREK-753R Bare bone with Z510PT 1.1GHz CPUTREK-753R-1A0E TREK-753R Bare bone with Z520PT 1.3GHz CPUTREK-753S-0A0E TREK-753R Bare bone with 1.1G CPU/Sunlight readable touch screenTREK-753R-CWBXPA0E TREK-753R w/CDMA/GPS/WLAN/BT/1GB RAM/4G CF/WESTREK-753R-HWBXPA0E TREK-753R w/HSDPA/GPS/WLAN/BT/1GB RAM/4G CF/WESTREK-753R-GWBXPA0E TREK-753R w/GPRS/GPS/WLAN/BT/1GB RAM/4G CF/WES
TREK-753 User Manual vi(2) this device must accept any interference received, including interference thatmay cause undesired operation.16. CAUTION: Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. 17. CAUTION: Always ground yourself to remove any static charge before touching the motherboard, backplane, or add-on cards. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components on a static-dissipative surface or in a static-shielded bag when they are not in the chassis.18. CAUTION: Any unverified component could cause unexpected damage. To ensure the correct installation, please always use the components (ex. screws) provided with the accessory box.Safety Precaution - Static ElectricityFollow these simple precautions to protect yourself from harm and the products fromdamage.To avoid electrical shock, always disconnect the power from your system chas-sis before you work on it. Don't touch any components on the main board or other cards while the system is on.Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive elec-tronic components.Warning! 1. Input voltage rated: 6 ~ 36 Vdc (12/24V power) or 18 ~ 58 Vdc (48V power, option).2. Transport: carry the unit with both hands and handle with care.3. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator.4. CF/SD/SIM card: Turn off the power before inserting or removing CompactFlash storage cards.
vii TREK-753 User Manual ContentsChapter 1 General Information ............................11.1 Introduction ............................................................................................... 21.2 General Specifications .............................................................................. 31.3 Dimensions ............................................................................................... 5Figure 1.1 TREK-753 dimensions................................................ 5Chapter 2 System Setup.......................................72.1 A Quick Tour of the TREK-753 Computer ............................................. 8Figure 2.1 Front view of TREK-753 ............................................. 8Figure 2.2 Rear view of TREK-753.............................................. 8Figure 2.3 Side view of TREK-753 .............................................. 9Figure 2.4 Bottom view of TREK-753 .......................................... 92.2 Installation Procedures............................................................................ 102.2.1 Connecting the Power Cord........................................................ 10Figure 2.5 Power connector photo............................................. 10Table 2.1: Pin Definition of Power Cord .................................... 112.2.2 Power Connector ........................................................................ 11Figure 2.6 Power connector outlook .......................................... 11Table 2.2: Power Connector...................................................... 112.3 Running the BIOS Setup Program .......................................................... 122.4 Installing the Drivers for Win XP ............................................................. 12Chapter 3 Hardware & Peripheral Installation ..133.1 Overview of Hardware Installation & Upgrading ..................................... 143.2 Installing the Storage Device and SIM Card ........................................... 143.3 Installing System Memory ....................................................................... 153.4 Installing Optional Accessories ............................................................... 153.5 Installing IO Cover................................................................................... 163.6 Installing Wireless options....................................................................... 193.6.1 WLAN.......................................................................................... 19Figure 3.1 Top view of TREK-753 ............................................. 193.6.2 GPRS.......................................................................................... 22Figure 3.2 Top view of TREK-753 ............................................. 223.6.3 HSDPA (3.5G) ............................................................................ 25Figure 3.3 Top view of TREK-753 ............................................. 253.6.4 CDMA (3.5G) .............................................................................. 273.6.5 GPS ............................................................................................ 29Figure 3.4 Bottom view of TREK-753 ........................................ 29Chapter 4 Pin Assignments ...............................314.1 Rear Side Connectors............................................................................. 324.2 Power Connector .................................................................................... 32Table 4.1: Power Connector...................................................... 324.3 High density Connector........................................................................... 33Table 4.2: High Density Connector............................................ 334.4 RS-232 Connector (COM8)..................................................................... 34Table 4.3: Table 5.5: RS-232 / RS-485 / J1708 Connector....... 344.5 LED Indicator .......................................................................................... 34
TREK-753 User Manual viiiChapter 5 Software Demo Utility Setup............ 355.1 Introduction ............................................................................................. 365.1.1 Execute J1939 Demo Utility........................................................ 36Figure 5.1 IMC demo utility........................................................ 36Figure 5.2 J1939 test - 1 & 2 ..................................................... 375.2 Hoy Key Test .......................................................................................... 37Figure 5.3 Hot Key .bmp............................................................ 375.3 RTC Test................................................................................................. 38Figure 5.4 RTC test - 1 & 2........................................................ 38Figure 5.5 RTC test - 3 & 4........................................................ 39Figure 5.9 RTC test - 5 .............................................................. 395.4 Vehicle Power Management ................................................................... 405.4.1 Power Management Mechanism ................................................ 405.4.2 Power Management Utility Program ........................................... 415.4.3 Power Management Parameter Settings.................................... 42Figure 5.10Power management test utility ................................. 425.4.4 TREK-753 Power Consumption.................................................. 425.5 Execute CAN Demo Utility ...................................................................... 43Figure 5.11CAN test ................................................................... 435.6 GPIO Test ............................................................................................... 44Figure 5.12DI/O test ................................................................... 44Figure 5.13Digital in.................................................................... 44Figure 5.14Digital out ................................................................. 455.7 Video in Test ........................................................................................... 45Figure 5.15 Video test utility ...................................................... 455.8 Audio Test............................................................................................... 46Appendix A High Density Cable Pin Assignment47A.1 Standard USB A type female connecter ................................................. 48Table A.1: Standard USB A type female connecter................... 48A.2 Video input, BNC female connecter........................................................ 48Table A.2: Video input, BNC female connecter ......................... 48A.3 RS-232 connecter (DB9 male)................................................................ 49Table A.3: RS-232 connecter (DB9 male) ................................. 49A.4 4DI /4DO & RS-485 (DB15 male type) ................................................... 49Table A.4: 4DI /4DO & RS-485 (DB15 male type)..................... 49A.5 CAN Bus & J1708 (Terminal Block 6P, 5.08mm pitch)........................... 50Table A.5: CAN Bus & J1708 (Terminal Block 6P, 5.08mm pitch)50A.6 Power extension connecter (Terminal Block 3P, 5.08mm pitch) ............ 50Table A.6: Power extension connecter (Terminal Block 3P, 5.08mm pitch)........................................................... 50A.7 High Density & Connecter Pin List.......................................................... 51Appendix B EWF(Enhanced Write Filter)Manager SOP53B.1 EWF(Enhanced Write Filter)Manager SOP ............................................ 54
Chapter 11General Information This chapter gives background information on the TREK-753 Computer.Sections include:IntroductionGeneral SpecificationsDimensions
TREK-753 User Manual 21.1 IntroductionAdvantech-DLoG’s TREK-753 is a new generation, all-in-one Computerwith touchscreen. Its compact and rugged industrial design is perfect for in-vehicleuse where space, vibration, transient power, and temperature fluctuations will dam-age most computer equipment. TREK-753 is the higher performing cousin of theaward-winning TREK-743 with its Intel® Atom™ Z510PT/US15 processor, increasedmemory, the addition of an analog video input port, GbE LAN, and a rich complementof I/O ports (additional COM ports, audio, CAN bus, and J1708). TREK-753 has alsobeen re-engineered to optimize internal space, gained by its full-flat panel touch-screen; and it has moved the CF/SD/SIM card slot to make it externally accessible,allowing easy access without having to open the unit.TREK-753 is built tough. It has an EN 60721-3-5 certification, and meets militarystandards for vibration and shock. This ruggedness allows TREK to boldly go whereothers dare not, opening a wide range of vertical market applications. TREK-753 issuitable for taxi and bus transport, in vehicle fleets of all types, in long-haul trucking,and as an affordable solution to heavy duty vehicle applications. TREK-753 isdesigned to operate flawlessly in transient power conditions. It supports 12/24 Voptions, operating from 6 ~ 36 volts, and it is ISO7637-2 and SAEJ1113 compliant.With power-on/power-off delay features which are software configurable, TREK holdsits own in unstable power conditions. And TREK can operate in the temperatureextremes found in vehicle environments. I/O Connectors
3 TREK-753 User ManualChapter 1 General Information1.2 General SpecificationsKey features7" WVGA LCD with 5 programmable adjustable brightness hot keySupport Windows Embedded System(W.E.S.) & WinCE6.0 & Linux UbuntuAnalog video input, J1708 & CAN2.0b with J1939 protocol supportedSupport CDMA/HSDPA/GPRS, GPS, WLAN, BT wireless communications12V/24V option: 6~36V input range compliant to IOS7637-2 & SAE J111348V option: 18~58V input range for specific applications Fan-less and ruggedized chassis with aluminum able to work under -30° C ~ 60° CIP54 rating with whole system protection in harsh environment under shock & vibration (Passed EN60721-3-5 5M3 Shock/vibration 100G/4G test.)SpecificationsDimensions: (W x H x D) - 255.7 x 161 x 56 mm (10.04" x 6.30"x2.20")Weight: 2.2 kg (max.)Vehicle power feature:–Input voltage: 6 ~ 36 Vdc, support ignition cold crank –Supports Ignition on/off–Supports low battery shut-down protection threshold (optional)–Supports power off event delay–Supports power on delay–Supports power low delay–Supports power low hard delay –Supports hard off delayCPU/Chipset: Intel industrial Atom (eMenlow) 1.1GHz /1.33GHz (optional)Chipset: On board Intel LE82US15EEOS: Windows Embedded System(W.E.S.) & WinCE6.0 & Linux Ubuntu RAM: One 200-pin SODIMM socket, Supports up to 2 GB DDR2 400/533Storage:–1 x SD card with external access (not for boot device)–1 x external accessible type ll Compact Flash memory card only (boot device)–1 x SIM card socket for GPRS/HSDPA LCD: Display Type 7" 16:9 industrial degree TFT LCD, 800x480 resolution LED backlight.Touch screen: Type 4 wires Analog resistive type, continuous resolution, optional to support sunlight readable TSIO Function:–1 x video input port for rear view monitor (Note: bypass video to screen, not support video recording)–1 x RS-232 COM port from rear IO; 1 x RS-232 COM port & 1x RS-485 port from high density connecter.–1 x USB 2.0 port from front panel; 1 x USB 2.0 port from rear IO; 1x USB 2.0 from high density connecter–1 x 100/1000-T Gb LAN by RJ45 connecter–1 x CAN 2.0B with J1939 protocol by High density connector–1 x J1708 by High density connector–1 x built-in 2.0w speaker & 1 x built-in microphone in front panel
TREK-753 User Manual 4–1 x Line-in/Line-out/Mic.in I/F by High density connector or switch to high density connector (by software)–5 x green lighted, programmable function keys, 2 x for LCD brightness control–1x light sensor on front cover for auto LCD brightness control–4 x isolated DI & 4 x isolated DO RF Function:GPS:Built-in uBlox LEA-5S GPS module with external antenna in IO plateBluetooth: Built-in Class 2 Bluetooth V2.0 + EDR moduleWWAN:–GPRS module by Cinterion MC55i with SMA type antenna–HSDPA module by Sierra wireless MC8790V with SMA type connector–CDMA module by Sierra wireless MC5728V with SMA type connectorWLAN: Built-in 802.11b/g/n module with SMA type connectorPower Supply:–Input Voltage 12V/24V option support 6~36V car power design with ISO7637-2 & SAE J1113 compliant–48v option support 18~58V input for specific application (Option)Mechanical Design:–Aluminum chassis with Optional to support whole system IP54 by extended IO cover–Weight- under 2.2 kg (~4.85 lbs)–Dimensions (W x H x D) - 255.7 x 161 x 56 mm (10.04" x 6.30" x2.20")Environmental Specifications:–Operating Temperature : -30° C ~ 60° C–Relative Humidity 95% @ 40° C (No condensing)–Vibration & Shock: MIL-STD-810G (US highway truck), Method 516.5, –SAE J1455, Class 5M3 according DIN EN 60721-3-5 (Lv.2 100G, 6ms, shock)
5 TREK-753 User ManualChapter 1 General Information1.3 DimensionsFigure 1.1 TREK-753 dimensions30 161255.7755654 75 4-M5
TREK-753 User Manual 6
Chapter 22System SetupThis chapter details system setup on TREK-753.Sections include:A Quick Tour of the ComputerInstallation ProceduresRunning the BIOS Setup Pro-gramInstalling the Drivers for Win XP
TREK-753 User Manual 82.1 A Quick Tour of the TREK-753 ComputerBefore starting to set up the Computer , take a moment to become familiarwith the locations and functions of the controls, drives, connectors and ports, whichare illustrated in the figures below. When the computer is placed insidetruck glove cabinet or under the passenger’s seat next to the driver, its front appearsas shown in Figure 2.1.Figure 2.1 Front view of TREK-753 Figure 2.2 Rear view of TREK-753
9 TREK-753 User ManualChapter 2 System SetupFigure 2.3 Side view of TREK-753 Figure 2.4 Bottom view of TREK-753
TREK-753 User Manual 102.2 Installation ProceduresWhen you installing TREK-753, the first step will be connect the car power and igni-tion correctly. TREK-753 power cable is designed to connect car battery directly.TREK-753 can be switched ON/OFF by the car ignition signal or its power buttonboth.2.2.1 Connecting the Power CordConnect the three pin waterproof power cord to the DC inlet of TREK-753. On theopen-wire end, one pin is reserved for positive voltage and is marked "+" whichneeds to be connected to the car power "+" side; one pin is reserved for ground andis marked "-"; which needs to be connected to the car power "-" side. And, one pin isreserved for the ignition signal with an “ignition” mark. There's independent "Shield"pin in power cable, please fixed its O-ring which besides of power connecter ofTREK-753.Connector : DECA Switchlab ME050-50803Mating connector: MC101-50803-3Y Figure 2.5 Power connector photoNote! TREK-753 power input support 12V/24V & 48V DC input. The default setting is for 12V or 48V (option board) only. If customer needs 24V DC input, please contact regional sales or distributors to customized in advance.Note! The Fuse for 12V/24V (10A) system and for 48V (5A) in power cable are different. Please check the fuse in your power cable before system power on. Note! Ignition on/off setting: The TREK-753 supports an ignition on/off function so that you can power on/off the TREK-753 via the ignition signal/volt-age and connect the TREK-753 vehicle ignition switch.
11 TREK-753 User ManualChapter 2 System Setup2.2.2 Power ConnectorTREK-753 can be powered on/off by power button or Acc ignition directly. Ignition on/off will have 5sec (default) delay when power on/off. It can avoid the floating carpower supply impact or damage system operation. For more detail of power manage-ment, please see Power mangement in Chapter 5. Figure 2.6 Power connector outlookTable 2.1: Pin Definition of Power CordPin Definition Color1+Red2 Shield Black3- Black4 Ignition OrangeTable 2.2: Power ConnectorPin Signal Pin Signal1Ground 2 Power input (6~36VDC;18~58VDC)3 Acc Ignition Input
TREK-753 User Manual 122.3 Running the BIOS Setup ProgramIn most cases, the computer will have been properly set up and configured by thedealer or SI prior to delivery. However, it may still be necessary to adjust some of thecomputer's BIOS (Basic Input-Output System) setup programs to change the systemconfiguration data, like the current date and time, or the specific type of hard drivecurrently installed.The setup program is stored in read-only memory (ROM). It can be accessed eitherwhen turning on or resetting the computer, by pressing the “Del” key on the keyboardimmediately after powering up the computer.The settings that are specified with the setup program are recorded in a special areaof the memory called CMOS RAM. This memory is backed up by a battery so that itwill not be erased when turning off or resetting the system. Whenever the power isturned on, the system reads the settings stored in CMOS RAM and compares themto the equipment check conducted during the power on self-test (POST). If an erroroccurs, an error message is displayed on screen, and the user is prompted to run thesetup program.2.4 Installing the Drivers for Win XPAfter installing system software, the computer is ready to set up the Intel® chipset,VGA, audio, LAN, and touch screen functions. All the pre-requisite drivers are storedon a CD-ROM disc entitled “Drivers and Utilities” (Check the correct wording on theCD, which can be found in the accessory box.)The utility directory includes multimedia programs. Some drivers and utilities in theCD-ROM disc have their own text files which help users install the drivers and under-stand their functions.These files are a very useful supplement to the information in this manual. For moreupdated driver please refers to Advantech website, www.advantech.com/supportThe drivers for TREK-753 are listed as below, please just execute the drivers forinstallation. Device VersionIntel SCH INF Update 8.8.0.1011Intel US15 GMA500 Graphic Driver 6.14.11.1018PenMount Universal Driver 2.1.1.0Realtek RTL8111DL 10/100/1000 PCI-E NIC 5.728.604.2009Realtek ALC892 High Definition Audio 5.10.0.5804FTDI FT4232 BUS USB Driver 2.6.0.0ublox LEA-5S Driver 1.2.0.5Sierra Wireless MC5728V 5.1.2535.0Sierra Wireless MC8790V 6.20.0.7Ralink RT3091 Wireless LAN Card (AW-NE768) 1.4.2.1BT-203B Utility BlueSoleil (Optional) 2.1.3.0Note! The drivers and utilities used for the TREK-753 are subject to change without notice. If you are in doubt, check Advantech's website or contact our application engineers for the latest information regarding drivers and utilities.
Chapter 33Hardware & Peripheral InstallationThis chapter details the installa-tion of hardware for TREK-753.Sections include:Overview of Hardware Installa-tion and UpgradingInstalling the Storage Device and SIM CardInstalling System MemoryInstalling the Drivers for Win XP
TREK-753 User Manual 143.1 Overview of Hardware Installation & UpgradingThe computer consists of a industrial computer that is housed in a rugge-dized aluminum enclosure. Any memory module or storage maintenance or hard-ware upgrades can be completed after removing the rear side RAM door/ Side cover,or remove the front panel to install.3.2 Installing the Storage Device and SIM CardTREK-753 has a side door and user can install SIM card and storages (CF or SDcard) easily. CF card is the main bootable storage which has OS pre-installed fromAdvantech. CF slot with a ejector (on the top side) then you can press and CFejected from socket. SD card as a secondary storage in TREK-753, system is NOTallowed boot up from SD.Note! Please do NOT paste any sticker or label on CF and SD , it might be jammed and not able to ejected from slot/socket.
15 TREK-753 User ManualChapter 3 Hardware & Peripheral Installation3.3 Installing System MemoryTREK-753 support 200-pin SO DIMM type DDRII DRAM. There's a door can be openfor RAM installation.It is very easy to open to install memory. But, we suggest thischange performed by our service center to avoid any possible damage (like ESD orwrong position inserted).3.4 Installing Optional AccessoriesOptional accessories, like RAM mount kits or other functional modules are availablefor purchase to complement TREK-753. All of standard 75mm type mounting with M5type screws only.Note! For system thermal design, please make sure the thermal pad on RAM door (Block in black) is always needs to be assembled before the door re-covered.(To bare bone system ,thermal pad will be placed in the accessory box).
TREK-753 User Manual 163.5 Installing IO CoverFor TREK-753 whole system IP54 ability, here is a IP54 IO cover kit to mask all theconnecters of bottom side. It's a rubber-metal kit includes a rubber cover, a screwsmounting frame, batten & batten with boss. From left to right: Rubber cover; mounting frame, batten with boss & batten, screws.Put the frame on the rubber cover, and lead all cables across the cover out side in.
17 TREK-753 User ManualChapter 3 Hardware & Peripheral InstallationConnect all cables to system and fix in tie before the cover installed.There're 6 screws holes designed for extra mechanic part installation. The mountingframe needs to be fixed with these holes.Install the cover by 6 screws installed. It will be easy to install rear side first (3screws) first.
TREK-753 User Manual 18Then install frame with other 3 screws at top side.Insert the batten with boss to the rubber cover. Please place all cables in the rightposition before another batten fixed in tight.Installation complete.
19 TREK-753 User ManualChapter 3 Hardware & Peripheral Installation3.6 Installing Wireless optionsTREK-753 is a highly integrated all-in-one terminal, all wireless options are able toinstalled at once and works by independent connection. In the standard OS compan-ioned with TREK-753, all the wireless connections have been setup in advance andusers will not have to setup again. These information provided for those who needsto build new wireless connections if necessary. RF options include:BluetoothWireless LAN(WLAN)WWAN (GPRS/CDMA/HSDPA)GPS3.6.1 WLAN Driver installation1. Make sure the Wi-Fi module has install to the TREK-753.Figure 3.1 Top view of TREK-753Note! All of hardware or reconfiguration changes should be performed by ser-vice center or authorized institutions of ADVANTECH.
TREK-753 User Manual 202. Make sure there is/are wireless router/AP working in same circumstance which TREK-753 is able to connect with. 3. Turn on the TREK-753, booting into OS.4. Double click the "Setup.exe" in driver CD (WLAN_AW-NE768_090714) to install driverSetup connection1. Press Start - Control panel - Network connections - Press right button of mouse and select properties in Wireless Network connection, then click "View Available Wireless Networks".
21 TREK-753 User ManualChapter 3 Hardware & Peripheral Installation2. Double click the available wireless LAN icon on the down-right corner and search for AP devices.3. There might have some APs devices appear with different SSID, choice the available one and connect with (might need to input user's ID & password)4. Click "Connect" to connect with wireless AP. Open the web browser and TREK-753 will connect to internet.
TREK-753 User Manual 223.6.2 GPRSDriver installation1. Make sure the Criterion MC55i GPRS module has install to the TREK-753.Figure 3.2 Top view of TREK-7532. Insert the User's SIM card to slot of TREK-753, make sure the User's SIM card has applied the GSM and data transmit/receive service in advance.3. Turn on the TREK-753, booting into OS.4. GPRS(MC55i) connected with system by COM port interface, it don't have to install driver. But, please check the device manager without any question mark in advance.
23 TREK-753 User ManualChapter 3 Hardware & Peripheral InstallationSetup connection1. Press Start - Control Panel - Phone and Modem options.2. Switch to Dialing rules tab, press button "New", input GPRS to the Location name, input "00" to Area code.3. Switch to Modems tab, press button "Add", select the "Don't detect my modem; select it from a list" - Next.4. Choose "Standard 19200 bps Modem" - Next.5. Select COM port - Next - Finish, the screen will display the "standard 19200 bps Modem" item.6. Press button "Properties", switch to Modem tap and select "Maximum Port Speed" change speed from 19200 to 115200 - press ok.7. Switch to advanced tap, in extra setting textbox, input:at+cgdcont=1,"IP","inter-net" - press ok.8. In the Network Connections Panel, Select Make New Connection.9. In the Make New Connection Dialogue, choose "Connect to the Internet" , then click next.10. Choose "Set up my connection manually", then click next.11. Choose "Connect using a dial up modem", then click next.12. Input ISP Name (ex: GPRS) then click next.13. Do NOT input Phone number, User name and Password.14. In completing the new connection wizard textbox, select "Add a shortcut to this connection to my desktop", then click Finish.15. In the Network Connections Panel, press right button of mouse then select properties.16. In the "Phone number textbox, input:*99***1#, then click Configure.
TREK-753 User Manual 2417. Change "Maximum speed (bps) to 115200,then click OK.18. Once complete previous steps, the new connection will be created.19. Double Click the new connection and Click Button "Dial", then the TREK-753 will connect to the internet.
25 TREK-753 User ManualChapter 3 Hardware & Peripheral Installation3.6.3 HSDPA (3.5G)Driver installation1. Make sure the HSDPA module has install to the TREK-753.Figure 3.3 Top view of TREK-7532. Insert the User's SIM card to slot, make sure the User's SIM card has applied the 3G service.
TREK-753 User Manual 263. Turn on the TREK-753, then booting into OS.4. Install the HSDPA USB module driver/AP "Watcher_Generic Build 2258.msi" from driver CD into the Windows Embedded OS.Setup connection1. Check the device manager without any question mark.2. In completing the new connection wizard textbox, select "Add a shortcut to this connection to my desktop", then click Finish.3. Once complete previous steps, the new connection will be created.
27 TREK-753 User ManualChapter 3 Hardware & Peripheral Installation4. Double Click the "Sierra Wireless Watcher" and Click Button "Connect", then the TREK-753 will connect to the internet.3.6.4 CDMA (3.5G)Driver installation1. Make sure the CDMA module has install to the TREK-753.
TREK-753 User Manual 282. Insert the User's SIM card to slot, make sure the User's SIM card has applied the 3G service.3. Turn on the TREK-753, then booting into OS.4. Install the CDMA USB module driver "Watcher 7.11.msi" into the Windows Embedded OS.Setup connection1. In completing the new connection wizard textbox, select "Add a shortcut to this connection to my desktop", then click Finish.2. Once complete previous steps, the new connection will be created.3. Double Click the on desktop and Click Button "Connect", then the TREK-753 will connect to the internet.
29 TREK-753 User ManualChapter 3 Hardware & Peripheral Installation3.6.5 GPSInstallation1. Make sure the GPS module & antenna has install to the TREK-753.Figure 3.4 Bottom view of TREK-7532. Turn on the TREK-753, booting into OS.3. Double click the "ublox_A4_U5_USB_drv3264_install_UI.exe" application pro-gram in driver CD and install to TREK-753 OS.
TREK-753 User Manual 30Setup connection1. Install the "u-Center" for setup and test.2. Start test in "u-Center", setting COM port (COM7) and baud rate (9600bps) use for GPS module.3. After start test, the NMEA output messages are display on the Development Data View setup connection.
Chapter 44Pin AssignmentsThis chapter explains pin assign-ments on the TREK-753.
TREK-753 User Manual 324.1 Rear Side Connectors4.2 Power ConnectorTable 4.1: Power ConnectorPin Signal Pin Signal1 Ground 2 Power input 3 Acc Ignition InputNote! TREK-753 has 2 power options for different vehicle:Input Voltage 12 V/24 V option support 6~36 V car power design with ISO7637-2 & SAE J1113 compliant (default)48 V option support 18~58 V input for specific application (Option)
33 TREK-753 User ManualChapter 4 Pin Assignments4.3 High density ConnectorTable 4.2: High Density ConnectorPin Signal Pin Signal1 +5VDC output (+/- 5%, max 0.5A) 2 +5VDC output (+/- 5%, max 0.5A)3 USB Ground 4 USB D+5USB D- 6 CVBS Ground7CVBS IN 8 RSVD9Audio Ground 10 LINE OUT L11 LINE OUT R 12 LINE IN R13 LINE IN L 14 MIC IN15 RS-485 Ground 16 COM5 485-17 COM5 485+ 18 J1708 Ground19 COM6 J1708- 20 COM6 J1708+21 Isolation CAN Ground 22 CAN L23 CAN H 24 RSVD.25 RSVD. 26 +12VDC output27 +12VDC output 28 +12VDC output29 Power Ground 30 Power Ground31 Power Ground 32 COM9 RS232 RI#33 COM9 RS232 CTS# 34 COM9 RS232 RTS#35 COM9 RS232 DSR# 36 RS232 Ground37 COM9 RS232 DTR# 38 COM9 RS232 TXD39 COM9 RS232 RXD 40 COM9 RS232 DCD#41 RSVD. 42 Isolated Relay Driver Output 4#43 Isolated Relay Driver Output 3# 44 Isolated Relay Driver Output 2#45 Isolated Relay Driver Output 1# 46 Isolated Dry Contact Input 447 Isolated Dry Contact Input 3 48 Isolated Dry Contact Input 249 Isolated Dry Contact Input 1 50 Isolation DIO Ground
TREK-753 User Manual 344.4 RS-232 Connector (COM8)4.5 LED IndicatorThis system power indicator is an orange LED,controlled by hadrware.This LED will be lit on when the system is in NORMAL mode.When system is off, this LED will be lit off.Table 4.3: Table 5.5: RS-232 / RS-485 / J1708 ConnectorPin Signal Pin Signal1 RS-232 DCD 2 RS-232 RXD3 RS-232 TXD 4 RS-232 DTR5 RS-232 Ground 6 RS-232 DSR7 RS-232 RTS 8 RS-232 CTS9RS-232 RI / +12 VDC (max. 2500 mA)
Chapter 55Software Demo Utility SetupThis appendix explains the soft-ware demo utility for TREK-753.Sections include:IntroductionHow to Set up Demo UtilityInstalling the Drivers for Win XP
TREK-753 User Manual 365.1 IntroductionTo make the hardware easier to access for programmers, Advantech has developeda demo utility in order to let customer test the functions on TREK-753. This documentdescribes detailed information for each Advantech demo utility so that applicationdevelopers can become more familiar with using them.For technical support, contact Advantech application engineers worldwide. For newsupdates, visit our website: www.advantech.com5.1.1 Execute J1939 Demo UtilityThis section explains how to install the Advantech demo utility in Windows XP Pro /Embedded.1. Execute the test program called “IMC_Demo”Figure 5.1 IMC demo utility2. Click J1939: customer may connect directly to the truck; we use a car simulator board below to explain how J1939 protocol can be executed. First, connect to the simulator board to TREK-753 CAN port and console PC, once the simulator is powered on (connect to the truck), you can start getting the data, just click [Read], you may get the data you need from the car simulator, click [Read], you may transfer the data to Console.
37 TREK-753 User ManualChapter 5 Software Demo Utility SetupFigure 5.2 J1939 test - 1 & 25.2 Hoy Key Test Click "Hot Key test" program in IMC demo main menu.If check "Auto Brightness"; TREK-753 will adjust the panel brightness automaticallyby build in Light sensor input. Or user can set the brightness of panel and hot keymanually.Figure 5.3 Hot Key .bmp
TREK-753 User Manual 38Brightness level: Check "Set" option then key in brightness from level 0 ~10 in "Cur"column.The number bigger, the panel is brighter.When you finish setting the brightness level you want, please click "Apply". If you want to check the current brightness level, please click "Get".Duty cycle: You may set every level's brightness strength, to every levels,After you finish setting the "Level" and "Duty Cycle" vaule for each level, click "Apply". If you want to check the current brightness strength on certain level, please click"Get".Light sensor: When the sensor has detected the change of the brightness in theenvironment, the value will change. The lowest level of brightness, the lowestvalue it is presented. On the contrary, the highest level of brightness, the highestvalue it is presented.Hotkey: the backlight brightness of hotkeys could be adjusted by setting the valuefrom 0 ~100.Key Status: When you press Hot key, the status will change from 0 to 1.Key function Definition: Set the parameters to connect to the application programfunction of the hot key.5.3 RTC TestExecute “RTC test”1. For RTC Time setting: You may set year, month, date, and time show as below. Figure 5.4 RTC test - 1 & 2
39 TREK-753 User ManualChapter 5 Software Demo Utility SetupFigure 5.5 RTC test - 3 & 42. RTC Alarm Setting: You may also set Alarm time; you may wake up the system by the time you have set. Please refer to the below figure.Figure 5.9 RTC test - 5
TREK-753 User Manual 405.4 Vehicle Power Management 5.4.1 Power Management MechanismThe feature of Vehicle Power Management (VPM) is provided for users to fulfill thespecial requirements on in-vehicle applications. Ignition on/off–Turn on the system by ignitionFor the cases of in-vehicle applications, an ignition signal is often used to turnon or shutdown the system. When the system is in an OFF state and ignitionis turn ON, the VPM controller will countdown ON_DELAY; once it counts tozero, the system will be turned on. –Shutdown the system by ignitionWhen the system is powered on and the ignition is turn off, theOFF_EVENT_DELAY will start to count down. During this stage, if the igni-tion is back to ON, the VPM controller will stop countdown and reset theOFF_EVENT_DELAY value. If OFF_EVENT_DELAY counts to zero, theVPM controller will send an event (power button press) to the system andstart to count HARD_OFF_DELAY. Application programs could watch thisevent to do pre-defined tasks, like storing data and preparing to turn off thesystem.Once going into the HARD_OFF_DELAY stage, this process will be irrevers-ible. And if HARD_OFF_DELAY counts to zero, the system power will be cutoff abruptly.Low battery protectionTo avoid draining out the car battery, low-battery protection is involved to ensurethe car battery is capable to start the vehicle. When the system is ON, the VPMcontroller will monitor the car battery voltage. If the battery voltage is lower thana programmable threshold (LOW_THRESHOLD), the VPM controller will go intoLOW_DELAY stage and start to count down. During the stage of LOW_DELAYcountdown, if battery voltage is back above LOW_THRESHOLD, the VPM con-troller will stop counting down and exit. If LOW_DELAY counts to zero, the VPMcontroller will send an event (power button press) to notify the system, go intoLOW_ HARD_DELAY stage and start to count down. Once LOW_HARD_DELAY counts to zero, the VPM controller will cut off the system powerabruptly to avoid draining out the car battery.The table below lists the user programmable parameters for VPM features:Default value Acceptable rangeON_DELAY 2 seconds 1 ~ 18000 secondsOFF_EVENT_DELAY 5 seconds 1 ~ 18000 secondsHARD_OFF_DELAY 60 seconds 1 ~ 18000 secondsLOW_THRESHOLD (12V mode) 11.42 V 10.09 ~ 12.25 VLOW_THRESHOLD (24V mode) 22.44 V 21.11 ~ 23.28 VLOW_DELAY 30 seconds 1 ~ 3600 secondsLOW_ HARD_DELAY 60 seconds 1 ~ 3600 seconds
41 TREK-753 User ManualChapter 5 Software Demo Utility Setup5.4.2 Power Management Utility ProgramExecute IMCDemo.exe file, see the icon below.
TREK-753 User Manual 425.4.3 Power Management Parameter SettingsThe parameters for power management on TREK-753 could be read or modified byDemo utility (see the image below) or SDK/API.Figure 5.10 Power management test utility5.4.4 TREK-753 Power ConsumptionOS: Windows Embedded StandardBurn-in test V6.0*Doesn’t support S1, S3, S4Power mode Power input range Power consumption(Typical) 12V/24V 6V~36V/6A(max) 36 Watt48V 18V~58V/2A(max) 36 Watt
43 TREK-753 User ManualChapter 5 Software Demo Utility Setup5.5 Execute CAN Demo UtilityFigure 5.11 CAN test1. Reset the module2. Transmit CAN message3. Set the polling rate of CAN message reception4. Received CAN message.5. Set up the filter of CAN message (only show the message ID)
TREK-753 User Manual 445.6 GPIO Test1. To execute the I/O Test, connect GPIO loopback, click Pin0, connect the end which reads the signal, the bulb should light up, like wise to Pin1~Pin3. Next check the Digital output box to execute the same procedure. See figure 6. Figure 5.12 DI/O test a. Digital Output ==> isolated relay driver outputb. Digital Input ==> isolated dry contact inputFigure 5.13 Digital in
45 TREK-753 User ManualChapter 5 Software Demo Utility SetupFigure 5.14 Digital out5.7 Video in TestThere are one video input, please connect camera to the port, CAM1. Choose Chan-nel 1 on [Switch to], then the panel will show the image which camera1 has taken,and it will recover to the same status after 10 sec. Figure 5.15 Video test utility
TREK-753 User Manual 465.8 Audio TestTREK-753 has a build-in microphone on front panel, and audio functions (Line outand Line-in & Mic.in) can be extended to remote site by High Density Cable.Both ofLine out & Line in function are work directly when High Density cable connected. Mic,in is able to works either front panel or from high density cable.
Appendix AAHigh Density Cable Pin Assignment
TREK-753 User Manual 48High Density connecter of TREK-753 includes 48 wires in a 2-meter cable. It extendsmany kinds and numbers IO port with standard type connecters for users.At the host side, it builds a 3M 10150-3000 PE series 50 pin connecter with able toconnected with TREK-753. At the connecter side, there are A.1 Standard USB A type female connecterA.2 Video input, BNC female connecter Table A.1: Standard USB A type female connecterPin Number Definition1 +V5_USB2 USB_D-3 USB_D+4 GND(Drain wire)Table A.2: Video input, BNC female connecterPin Number Definition1 CVBS_IN2 GND(Drain wire)
49 TREK-753 User ManualAppendix A High Density Cable Pin AssignmentA.3 RS-232 connecter (DB9 male)A.4 4DI /4DO & RS-485 (DB15 male type)Table A.3: RS-232 connecter (DB9 male)Pin Number Definition1 RS232_DCD2 RS232_RXD#3 RS232_TXD#4 RS232_DTR5 GND(Drain wire)6 RS232_DSR7 RS232_RTS8 RS232_CTS9 RS232_RITable A.4: 4DI /4DO & RS-485 (DB15 male type)Pin Number Definition1ISO_DI12ISO_DI23ISO_DI34ISO_DI45GND_ISO 9ISO_DO110 ISO_DO211 ISO_DO312 ISO_DO413 RS485+14 RS485-15 GND(Drain wire)
TREK-753 User Manual 50A.5 CAN Bus & J1708 (Terminal Block 6P, 5.08mm pitch)A.6 Power extension connecter (Terminal Block 3P, 5.08mm pitch)Table A.5: CAN Bus & J1708 (Terminal Block 6P, 5.08mm pitch)Pin Number Definition1CAN_H (H)2CAN_L (L)3 GND (G)4 J1708+ (J+)5 J1708- (J-)6 GND (G)Table A.6: Power extension connecter (Terminal Block 3P, 5.08mm pitch)Pin Number Definition1 +V12(26AWG)2 GND(26AWG)3 +V5(26AWG)
51 TREK-753 User ManualAppendix A High Density Cable Pin AssignmentA.7 High Density & Connecter Pin ListHigh Denisity(50pin) connecter Jacks & IO conn./pinNo. Siganl Name Function / Conn. No.1+V5(26AWG) Extended Power Terminal Block 3P, 5.08mm pitch 32+V5_USBUSB tpye Afemale connecter13 GND(Drain wire) 44 USB_D+ 35 USB_D- 26 GND(Drain wire) Video input BNC Connecter27 CVBS_IN 18N/A9 GND(Drain wire)Line out jack10 LINEOUT_Left11 LINEOUT_Right12 LINEIN_RightLine in jack13 LINEIN_Left14 MICIN Mic. In jack15 GND(Drain wire)DIO & RS-485DB15 female1516 RS485- 1417 RS485+ 1318 GND(Drain wire)CAN Bus & J1708Terminal Block 6P, 5.08mm pitch connecter619 J1708- 520 J1708+ 421 GND(Drain wire) 322 CAN_L 223 CAN_H 124 N/A25 N/A26 +V12(26AWG)Extended PowerTerminal Block 3P, 5.08mm pitch127 +V12(26AWG)28 +V12(26AWG)29 GND(26AWG) 230 GND(26AWG)31 GND(26AWG)
TREK-753 User Manual 5232 RS232_RIRS-232 male Connecter933 RS232_CTS 834 RS232_RTS 735 RS232_DSR 636 GND(Drain wire) 537 RS232_DTR 438 RS232_TXD# 339 RS232_RXD# 240 RS232_DCD 141 N/A42 ISO_DO4DIO & RS-485DB15 female connecter1243 ISO_DO3 1144 ISO_DO2 1045 ISO_DO1 946 ISO_DI4 447 ISO_DI3 348 ISO_DI2 249 ISO_DI1 150 GND_ISO (26AWG) 5
Appendix BBEWF(Enhanced Write Filter)Manager SOP
TREK-753 User Manual 54B.1 EWF(Enhanced Write Filter)Manager SOP1. Open Start -> All Programs -> Advantech -> Advantech EWF Manager. 2. You will get a user interface as the following picture. A. EWF function: If you want to protect your OS you can use the function. It willrecovery your OS after restarting OS.EWF enable method:1. Click Enable and UI will request restart OSNote! Please check "C" volume is not protected.
55 TREK-753 User ManualAppendix B EWF(Enhanced Write Filter)Manager SOP2. After restarting OS you will discover EWF state become "Enable"3. At this time, you can try to create folder or file and restart OS. You will discover you can't modify data under C volume.HORM(Hibernate Once and Resume Many): The function can always resume yourOS after hibernating, even shutdown or crash.I Before using HORM you should set EWF "disable"II Check "Enable hibernate"1. Right-Click on desktop and click "Properties"Note! If you want to write data at EWF enable state you can click Commit to write data under C volume.
TREK-753 User Manual 562. Choose "Screen Saver" panel and click "Power”.3. Check "Enable hibernate".
57 TREK-753 User ManualAppendix B EWF(Enhanced Write Filter)Manager SOPIII Activate HORM1. Open Start -> All Programs -> Advantech -> Advantech EWF Manager.2. Click "Activate HORM".3. Chick "OK" to reboot OS.IV Check "Use the Welcome screen".1. Open Start -> Control Panel.
TREK-753 User Manual 582. Click "Network and Internet Connections".3. Click "Network Connection".
59 TREK-753 User ManualAppendix B EWF(Enhanced Write Filter)Manager SOP4. Right-Click on "Local Area Connection" and click properties.5. Uninstall "Client Service for NetWare".6. Click "Yes" to remove "Client Service for NetWare" and reboot OS.7. Open Start -> Control Panel.
TREK-753 User Manual 608. Click "User Accounts"9. Click "Cancel".10. Check "Use the Welcome screen" and Click "Apply Options"
61 TREK-753 User ManualAppendix B EWF(Enhanced Write Filter)Manager SOPV Enable EWF1. Open Start -> All Programs -> Advantech -> Advantech EWF Manager.2. Click "Enable".3. Click "OK" to reboot OS.VI Run "Hibernate"1. Open Start -> Shut Down2. When you press "Shift" Standby will become Hibernate
TREK-753 User Manual 62VII Enable HORM finishVIII You can try to pull power cord after resuming. You will discover the OS always been resuming
63 TREK-753 User ManualAppendix B EWF(Enhanced Write Filter)Manager SOP
www.advantech.comPlease verify specifications before quoting. This guide is intended for referencepurposes only.All product specifications are subject to change without notice.No part of this publication may be reproduced in any form or by any means,electronic, photocopying, recording or otherwise, without prior written permis-sion of the publisher.All brand and product names are trademarks or registered trademarks of theirrespective companies.© Advantech Co., Ltd. 2011
65

Navigation menu