Advantech Co DLM8110WL Computer User Manual DLT M8110 Draft

Advantech Co Ltd Computer DLT M8110 Draft

Contents

User Manual

User Manual DLT-M8110 Computer PWS-870 User Manual
Copyright The documentation and the software included with this product are copyrighted 2016 by AdvantechDLoG Co., Ltd. All rights are reserved. AdvantechDLoG Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of AdvantechDLoG Co.,Ltd. Information provided in this manual is intended to be accurate and reliable. However, AdvantechDLoG Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use. Acknowledgements All other product names or trademarks are properties of their respective owners.
Declaration of Conformity CE Conformity Statement Radio products with the CE alert marking comply with the R&TTE Directive (1999/5/ EC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards)  EN 60950-1 (IEC60950-1) - Product Safety Products that contain the radio transmitter are labeled with CE alert marking and may also carry the CE logo. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; 2. This device must accept any interference received, including interference that may cause undesired operation. Caution! Exposure to Radio Frequency Radiation. The radiated output of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. When connecting an external antenna to the device, the antenna shall be placed in such a manner to minimize the potential for human contact during normal operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna  Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected  Consult the dealer or an experienced computer technician for help FCC RF Radiation Exposure Statement:  This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.  This equipment should be installed and operated with a minimum distance of 0mm between the radiator and your body.  Caution!  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  Antennas  Only use the supplied antenna. Unauthorized antennas, modifications or change to the antennas could violate FCC regulations and void the user’s authority to operate the equipment.  For operation within 5.15 ~5.25GHz /5.25 ~5.35GHz/5.47 ~5.725GHz frequency range, it is restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations. The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.  The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. FCC ID : M82-DLM8110WL Technical Support and Assistance 1. Visit the AdvantechDLoG website at http://support.advantech.com where you can find the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the following information ready before you call: – Product name and serial number – Description of your peripheral attachments – Description of your software (operating system, version, application software, etc.) – A complete description of the problem – The exact wording of any error messages Safety Instructions Use the following safety guidelines to help protect yourself and DLT-M8110  Do not attempt to service the DLT-M8110 yourself. Always follow installation instructions closely.  Be sure that nothing rests on the AC adapter's power cable and that the cable is not located where it can be tripped over or stepped on.  Do not cover the AC adaptor with papers or other items that will reduce cooling; also, do not use the AC adapter while it is inside a carrying case.  Use only the AC adapter, power cord, and batteries that are approved for use with this DLT-M8110. Use of another type of battery or AC adapter may cause risk of fire or explosion.  If you use an extension cable with the AC adapter, ensure that the total ampere rating of the products plugged in to the extension cable does not exceed the ampere rating of the extension cable.  When you move the DLT-M8110 between environments with very different temperature and/ore humidity ranges, condensation may form on or within the DLT-M8110. To avoid damaging the device, allow sufficient time for the moisture to evaporate before using the DLT-M8110.  When you disconnect a cable, pull on its connector or on its strain relief loop, not on the cable itself. As you pull out the connector, keep it evenly aligned to avoid bending any connector pins. Also, before you connect a cable make sure both connectors are correctly oriented and aligned.
Battery Safety RTC Battery Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.  Do not place the battery incorrectly as this may cause danger of explosion.  Dispose of used batteries according to the manufacturer's instructions.  Do not dispose of batteries in a fire. They may explode. Check with local authorities for disposal instructions. Battery Pack Caution  The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, heat above 60°C, or incinerate. Replace battery with Li-ion 7.2V 3800mAh and Cell SANYO only. Use of another battery may present a risk of fire or explosion.  Dispose of used batteries according to local disposal regulations. Keep away from children. Do not disassemble and do not dispose of in a fire. Battery Charge Notice It is important to consider the environment temperature whenever you are charging the Lithium-Ion battery pack. The process is more efficient at normal room temperature or slightly cooler. It is essential that you charge batteries within the stated range of 0°C to 45°C. Charging batteries outside of the specified range could damage the batteries and shorten their charging life cycle. Storage and Safety Notice Although charge Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to the build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at temperatures between -20°C to 60°C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room temperature ranges.
Chapter 1 Rugged and Ready to Go
Congratulations on your purchase of the DLT-M8110 Vehicle Mounted Terminal. This product combines rugged design with reliable performance and powerful functionality to best suit all your needs, in a wide range of working conditions. This user manual outlines all you need to know to set up and use your DLT-M8110. If you have any further questions or queries, contact our technical support team via our website: http://www.advantechdlog.com/ Symbols Used in this Manual Denotes information that must be observed. Failure to do so may result in personal harm or damage to the product. Denotes information that must be observed. Failure to do so may result in personal harm or damage to the product. Product Features •Powered by Intel® Haswell Bay Trial-I series E3827 CPU inside •10.4” XGA display with P-CAP and Resistive touch as optional • 8 user programmable function keys • Hot-swappable battery provides up to 8 hours operation. •Built-in camera, 2D barcode scanner and WiFi • Fully rugged design with MIL-STD-810F and IP65 certified. Package Contents Ensure all the following items are present when you receive your DLT-M8110. If any of these items are missing, contact your vendor immediately. Screens used in this manual are for illustrative purposes only. Actual screens may vary depending on your product version. • DLT-M8110 Vehicle mounted terminal
• AC power adaptor • 2x slim Batteries • Safety notes • Quick start guide Optional Accessories • Desk docking station • Vehicle docking station • Big battery • Battery charger
Exploring the DLT-M8110 Front View No. Component 1 Barcode/camera trigger button 2 Speaker 3 8 programmable function keys 4 Shift LED 5 WiFi LED 6 Bluetooth LED 7 Storage LED 8 Power LED 9 Temperature LED 123456789
Rear View No. Component 1 Camera 2 Battery 3 Hand strap 123
Side Views No. Component 1 USB 3.0 2 DC-in connector 21
Top View No. Component 1 Barcode scanner 2 Power on/off button Bottom View No. Component 1 Docking connector l 11 2
Chapter 2 Getting Started & Making Connections
Connecting the Power Before using your DLT-M8110, you must fully charge the battery. Connect the power adapter as shown and leave to charge for: • A minimum of 2 hours when using thin battery • A minimum of 5 hours when using think battery  You also can use vehicle docking, office docking or battery charger to charge the battery. Insert batteries on device When battery is fully charged, insert 2 batteries on device. Connecting USB Devices You can connect peripheral devices, such as a USB keyboard and mouse, as well as other wireless devices using the USB ports on the PWS-870. PWS-870 has one USB 3.0 port on the both side and one USB 2.0 port on the left side.
Chapter 3 Turning on & Controlling the DLT-M8110
Turning On 1. Press and hold the power button to turn on the DLT-M8110. 24 Controlling the DLT-M8110 Using the Touch Screen The DLT-M8110 is equipped with touch screen technology, for ease of use when you are on the go. Simply tap the screen with your finger to select icons and run applications. Using the Tap Function • To emulate a left click single tap the screen once. • To emulate a right click tap and hold the screen. • To emulate a double click, tap the screen twice. Using the On-Screen Keyboard Tap keyboard icon to bring up the on-screen keyboard.
Use your finger to tap and enter letters, numbers and symbols as you would with a regular keyboard. Making WiFi Connection WiFi access requires a separate purchase of a service contract with a wireless service provider. Contact a wireless service provider for more information. The DLT-M8110 comes pre-loaded with WLAN module, you can send and receive signals to a WiFi network then synchronize files.
A wireless network can be added either when the network is detected or by manually entering settings information. Before doing these steps, determine if authentication information is needed. 1. Click the wireless connection icon in the notification area. 2. Turn on WiFi and select one of the wireless connections and click Connect. 3. You are prompted to enter a Security key for secure access. Contact the network administrator for this key. 4. Enter the required Security key and then tap Next to connect. 5. The wireless connection is negotiated and you see the following screen.
The wireless connection icon in the notification area shows a connected status whenever a wireless connection is present. Making Bluetooth Connections The DLT-M8110 comes with built-in Bluetooth functionality that allows you to connect and communicate with other Bluetooth-enabled devices. Setting Up Bluetooth Follow these instructions to set up a Bluetooth connection. 1. Bluetooth is turned off in default setting, so if you want to connect to a Bluetooth device, please make sure the Bluetooth is turned on in Tap Module Control in Module page and turn on the Bluetooth
2. In notification area, tap Bluetooth logo and select Add a Device.
3. Select Bluetooth device and tap Next to add Bluetooth device. 4. Select Next for both DLT-M8110 and the blue tooth device after passkey is confirmed. 5. The Bluetooth device is successfully added into DLT-M8110.
6. To view Bluetooth device added, tap Show Bluetooth Devices. It is recommended that you use a passkey to prevent unauthorized access to your DLT-M8110.
Chapter 4 Using MDevice utility
MDevice for DLT-M8110 MDevice is a useful tool for user to get DLT-M8110 basic system information and control DLT-M8110 easily Install MDevice Utility Bylaunchingtheinstaller(SetupMDevice.msi),usercansimplyinstallMDeviceUtility. 1.DoubleClickinstallertotriggerinstallprocess 2.ClickNext
3.Modifyinstallfolderifnecessaryandsetwhocanusethistool;thenclickNextagain
4.ClickNext
5.Theinstallationisprocessing,pleasewaittillitfinished.6.InstallCompletely
After install ...1.Everytimedevicebootsup,MDeviceUtilitywillbelaunchedautomatically.2.MDeviceUtilitylinkwillappearinDesktop3.MDevice_UtilityandUninstalllinkswillappearinprogrammenu
Launch MDevice Utility BydoubleclickingtheMDevice_UtilitylinkinDesktoporclickingthelinkinuserprogrammenu,usercanlaunchtheutilitymanually.Theutilitywillrunatbackground.Usercanstarttoconfiguretheutilityorterminateitbybellowsteps:1. StartStep1.RightClickMDiconinSystemtray:Step2.ChooseStartConfigTool
2.  TerminatetheutilityStep1.RightClickiconinSystemtray:Step2.ChooseCloseLogin
Inthisform,usercandecidewhichmodetheutilitywillbe.ForUsermode,usercansimplyclick"Readonlywithoutpassword".ForAdministratormode,usershouldinputtheADMINpasswordandclick"OK". ForServicemode,userareaskedtoinputaone‐timepassword,whichgeneratedbyKey‐Generatetool.Login Permission TherearethreemodesinMDeviceUtility.UseMode:Userisabletoviewthewholesettingitems,butnotallowedtochangethesetting. Correspondingicons:.AdministratorMode:Userisabletoviewthewholesettingitems,butonlyallowedtosetlimitedsettingitems.Someofthesettingitemsareimpossibletochanged.
Correspondingicons:ServiceMode:Userisabletoview/modifythewholesettingitems.Correspondingicons:Menu Inmenuform,usercangointoeachsettingbysimplyclickthebutton.Note:ChangePasswordishiddeninusermode.
System Information Inthisform,userisabletowatchthesysteminformation.Onlyinservicemode,usercanclickthe  icontoconfiguretheS/N. Andthen,usercanbacktomenupagebyclicking  or .Power Setting
Inthisform,usercanconfigurethepowersetting. Switch‐On:Toconfigurewhichsourceisallowedtoturnonthedevice.Switch‐Off:Toconfigurewhichsourceisallowedtoturnoffthedevice.ScreenDisplay:Toconfigurethebehaviorwhilereceivingignitionoffevent.Blockinput:Whilereceivingignitionoffevent,alltheinputs(ex.touch,keyboard,mouse)willbeblocked.Showcounter:Whilereceivingignitionoffevent,utilitywillshowacountdowndialogtonotifytheuser.TimeDelaySeconds:Toconfigurethedelayseconds.
IgnitionOffDelay:ThewaitingtimetotriggeraOSshutdowneventwhileignitionoff.HardOffDelay:Thewaitingtimetotriggerapowershutdowneventwhileignitionoff.BatteryCapacityThreshold:Toconfigurethepercentagethresholdofbatteryforswitch‐on/offevent.SensorTemperatureThreshold:Toconfigurethetemperaturethresholdofeachsenorforswitch‐on/offevent.Andthen,usercanbacktomenupagebyclicking  or .Function Key Setting 
Thisformisforsettingorviewingthefunctionofeachfunctionkey.InSection1:Usercanswitchthetypeoffunction.Thereare4typesoffunctionusercanset:VKcodes:Thefunctionkeywhichissettothistypewillsendvirtualkeycodeswhichsupportsmaxto3combinationofkeys.Program:Thefunctionkeywhichissettothistypewilltriggeraapplication.Text:Thefunctionkeywhichissettothistypewillsendaplaintext.Camera:Thefunctionkeywhichissettothistypewilllaunchthecameraapplication.InSection2:Usercansetthedetailsofthefunctioninthissection.InSection3:Usercanswitchthefunctionkey.Module Setting
WLAN:Enable/DisableWiFi Bluetooth:Enable/DisableBTCamera:Enable/DisableCameraBarcode:Enable/DisableBarcodeG‐sensorautorotate:Enable/DisableG‐sensorautorotefeatureAntenna Setting
ThisformisforselectingAntenna.Brightness Setting
Thisformisforsettingbrightnessinexternalpowermodeorbatterymode.Network Startup
Networkstartupfeaturewillcheckthewhetherdeviceisconnectedwithserveratboot‐upstageandtakeactionaccordingtothecheckresult.EnableNetworkStartup:CheckedifuserwanttoenablethisfeatureProgramsforStartup:It'sforsettingthestartupprogramlist,usercanaddprogrambyclickingAddprogram...button,orremoveprogrambyRemovedprogrambutton.NetworkAdapter:Tospecifyanetworkadapterforthenetworkcheckingevent.ServerIP‐address(PING):It'sforsettingtheserverIP.TimeWaitingfornetwork:It'sforsettingthewaitingtimefornetwork,ifdevicescannotconnecttoserverwithinthetimelimit,thecheckresultofnetworkisfailed.Validateadapteravailabilityatstartup:Checkedifuserneedtochecktheadapteraswell.
Startprogramsevenwithoutnetwork:Checked,ifuserneedtolaunchthestartupprogramswhichlistinProgramsforStartup, eventhecheckingresultisfailed.Showinfodialog:Itisforsettingthetextinformationwhichwillbeshownduringcheckingnetwork.Touch Configuration Capacitancetouchsensitive:It'sforsettingthesensitiveoftouch.It'sonlyavailablewhendeviceisusingcapacitancetouch.ResistedTouchCalibration:It'sfortouchcalibration.It'sonlyavailablewhendeviceisusingResistedtouch.Change Password
ThisformisforchangingtheADMINpassword.
Chapter 5 Maintenance
Maintaining the Battery • Do not expose heat or attempt to disassemble the battery, and do not place the battery in water or in a fire. • Do not subject the battery to strong impact, such as a blow from a hammer, or stepping on or dropping it. • Do not puncture or disassemble the battery. • Do not attempt to open or service the battery. • Replace only with batteries designed specifically for this product. • Keep the battery out of reach of children. • Dispose of used batteries according to local regulations. Maintaining the LCD Display • Do not scratch the surface of the screen with any hard objects. • Do not spray liquid directly on the screen or allow excess liquid to drip down inside the device. • Do not place anything, such as food and drink, on the screen at any time to prevent damage to the screen. • Clean the LCD display only with a soft cloth dampened with denatured alcohol or a proprietary LCD screen cleaner. Cleaning the DLT-M8110 1. Turn off the DLT-M8110 and unplug the power cord. 2. Wipe the screen and exterior with a soft, damp cloth moistened only with water. Do not use liquid or aerosol cleaners on the screen, as these will discolor the finish and damage the screen. PWS-870 User Manual
Chapter 6 Appendix
Specifications Feature Specifications CPU & Chipset Intel Atom Baytrail-I, E3827 (1.75GHz) Memory Single SO-DIMM, DDR3L-1067, Up to 4GB. Storage SQF MSATA 820 MLC (-40 ~ 85°C), SLC option Display 10.4" XGA (1024 x768) LED Backlight LCD (340 bits) Touch Panel Gorilla Glass for PCAP touch solution or Chemical Tempered Glass for Resistive touch solution (Optional) Sensor Accelerometer (G-sensor), Screen Rotation: 0°, 90°, 270° Wireless Communication Default WIFI 802.11 a/b/g/n Default Bluetooth V4.0 (Class2) + EDR Camera 5M pixel CMOS Sensor Data Collection Built-in 2D barcode scanner Audio Output Integrated speakers Input Capacitive multi-touch Programmable button x8 On-screen QWERTY keyboard LED Status Indicator WiFi LED / Storage LED /Power LED / Battery LED / Temperature LED External I/O Interfaces USB 3.0 x 1 DC-in x 1 Docking Port x1 (32PIN) Power Supply Small battery: 2S1P 7.2V 1750mAh Big battery: 2S2P 14.4V 3800mAh AC Adapter: AC 100V-240V 50/60Hz OS Support Windows Embedded 8.1 Industry Pro 64bit Windows Embedded 8 Standard 64bit Windows Embedded 7 64bit Windows 7 Pro 64bit Temperature & Humidity(with battery) Operating Temperature: 0 to 45 ºC Storage Temperature: -20 to 60 ºC Operating Humidity: 5%~95% @ 40 ºC IP Rating IP65 Drop & Vibration MIL-STD-810F, Method 516.5, Procedure IV (or comparable EN test specification; see also test in regard to
810G). Description: Drop: 26 drops from 1.22 m onto concret EN60721 5M3 certified EMC CE/FCC/SAR/R&TTE/Telecom Safety UL/CB / LVD Accessories Vehicle Docking Station Desk Docking Station Big Battery Battery charger Dimensions 304mm (W) x 221mm (D) x 31.84mm (H) (w/thin battery) Weight 1.3kg without hand strap
LED Status Power / Thermal LEDDUTon/offGreenLED OrangeLED RedLEDRemarkOFF OFF OFF OFF SystemOFF(S5)ON Static OFF OFF SystemON(S0)ON Blinking OFF OFF SystemSLEEP(S3)ON OFF OFF StaticOverTemperatureON OFF OFF BlinkingSensorFaulty Front Battery LED DUTon/offACAdapterInBatteryGreenLEDOrangeLEDRedLED RemarkOFF x OFF OFF OFF SystemOff(S5)OFF OFF Static OFF BatteryChargingOFF OFF OFF OFF BatteryFull
ON x Static OFF OFF SystemOn(S0)Battery>30%ON OFF Static OFF BatteryChargingON OFF OFF OFF BatteryFullON x Blinking OFF OFF Battery<30%light0.5sec,dark0.5secON x OFF Blinking OFF Battery<10%light0.2sec,dark0.8secON/OFF xOFF OFF StaticBatteryReadFailure Rear Battery LEDs DUTon/offACAdapterInBatteryGreenLEDOrangeLEDRedLED RemarkON Static OFF OFF Battery>30%ON Blinking OFF OFF Battery<30%ON OFF Blinking OFF Battery<10%ON OFF OFF StaticBatteryReadFailureON xx OFF OFF OFF Battery
Removed

Navigation menu