Advanced Control Technologies 0685-0X HomePro Wall Mounted Infrared Sensor User Manual C 02 HOMEPRO RF MASTER CATALOG

Advanced Control Technologies, Inc. HomePro Wall Mounted Infrared Sensor C 02 HOMEPRO RF MASTER CATALOG

Manual

ZIR000 InstructionsP/D 092704HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0685-011Radio Frequency Transmitter, Battery Powered,Wall Mounted Passive Infrared (PIR) SensorZIR000HomeProRF Home AutomationShown with suppliedwall mount bracketZIR000 WALL MOUNTED SENSORThe ZIR000 Wall Mounted Sensor is a component of the HomePro lighting control system. Inclusion of this WallMounted Sensor on the ZTH100 Wireless Controller menu allows remote ON/OFF control HomePro receivers tocontrol lighting. Z-Wave nodes of other types can be added to the system and will also act as repeaters if they supportthis function of repeating the signal received to other modules in the system.There are no field repairable assemblies on this unit. It is covered by a one year limited warranty. If service is needed,the unit must be returned where purchased.CAUTION! Read and understand these instructions before installing. For indoor use only. Retain instructions forfuture use.INSTALLATIONBattery Installation and Sensitivity Selection1. Remove the screw from the bottom of the enclosure.3. Select the sensitivity setting preferred for the ZIR000 bysetting the corresponding jumpers on the electronicmodule.Note that H option is the highest sensitivity while the Loption is the lowest. See Figure 1.Mounting LocationThe ZIR000 is designed for indoor use. It should not be mounted near large metal objects or on metal sur-faces. It should be mounted on a wall or in a corner at a height of approximately 6.5 to 8.2 feet (2 to 2.5meters) for the best general coverage in an average room.The detector has been designed to avoid false alarms, nevertheless, it is best to avoid looking directly atsources of heat such as fires and boilers, and always try to keep away from a window.The ZIR000 can be positioned across from a radiator but not placed above one. Do not mount the ZIR000where its field of view may be obstructed (e.g. by curtains).39 foot (12 m) range, 110 degree coveragewith convex honeycomb hemisphericalinfra-red lensFig. 1
ZIR000 InstructionsP/D 092704HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0685-012Mounting the Detector1. Place the provided ZIR000 mounting bracket into the location you want to mount it. Mark the wall (orceiling) where the two screw holes are that will be used.2. Complete the following two steps if mounting in drywall, where there is not a stud.a. Drill a pilot hole of 11/64”.b. Tap the provided wall anchors into the wall (or ceiling).3. Screw the mounting bracket to the wall (or ceiling).4. Install the four AA batteries into the ZIR000 and snap the ZIR000 onto the mounting bracket.5. Adjust the vertical pattern angle per figure 2, if desired.Fig 2LENS can be adjusted to suit your needs by simply rotating the angle of the lens 180 o to change from wideangle version (Default setting) to long range version if required.WIDE ANGLEAngle: 105o x 110oDistance: 39 feet (12 meters)Zone Number: 64Default SettingLONG RANGEAngle: 5o x 5oDistance: 14mZone Number: 8Default Setting + 180oWalk Test (checking the detection field)3. Place the LED jumper in the “On” location. See figure 3.4. Replace the top enclosure and screw.5. Walk slowing across the field of view (Back and Forth)and observe the LED – it lights whenever you enter orexit a sensitive beam. Allow 5 seconds after the LED haslit to continue the test, this is so the unit can stabilize.6. After testing, remove the retaining screw and the top ofthe enclosure and and set the LED jumper back to theoff position.7. Replace top enclosure and retaining screw.
ZIR000 InstructionsP/D 092704HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0685-013Power Four (4) AAA batteriesMounting Mounting bracket providedSignal (Frequency) 908.42 MHzRange Up to 100 feet line of sight between the Wireless Controller and /or theMounted Dimensions (H x W x D) 4.125” x 2.6” x 3.10” (10.47cm x 6.6cm x 7.8 cm) closest HomeProReciever ModuleWARRANTYFor warranty and general product information visit our web site at www.act-solutions.comABOUT ZIR000’S CERTIFICATIONThe ZIR000 has been thoroughly tested by the ETL SEMCO divisionof Intertek, a nationally recognized testing laboratory. This productwas found to be in compliance with safety standards ANSI/UL STD 244A and CAN/CSA C22.2 No. 177.In addition to compliance with product safety standards, the ZIR000is also certified to comply with applicable FCC and IC rules andregulations governing RF and EMI emissions.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) This device must accept any interference received, including interference that maycause undesired operation.FCC NOTICENote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installedand used in accordance with the instructions may cause harmful interference to radio communications. However, thereis no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-aged to try to correct the interference by one or more of the following measures:- Increase the separation between the equipment and receiver.- Consult the dealer or an experienced radio/TV technician for help.IC NOTICEThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device.

Navigation menu