Advanced Control Technologies 0677-0X HomePro Plug-In Modules User Manual C HomePro RF HomePro RF Catalo

Advanced Control Technologies, Inc. HomePro Plug-In Modules C HomePro RF HomePro RF Catalo

Users Manual

ZDP100 Instructions101002HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0607-011Radio Frequency Controlled, 300W, 120 VAC, Plug-In Lamp ModuleZDP100HomeProRF Home Automation Button functions1. Adds module under the command of Wireless Control-ler.2. Local ON and OFF (push and release).3. Local dimming (hold down).ZDP100 PLUG-IN LAMP MODULEThe ZDP100 plug-in Lamp Module is a component of the HomePro lighting control system. Plug the Lamp Moduleinto a wall outlet and plug a lamp into the Lamp Module. Inclusion of the Lamp Module on the ZTH100 WirelessController menu allows remote ON/OFF control and dimming of lamps connected.This plug-in Lamp Module is designed to work with other HomePro lamp and appliance controls. Z-Wave nodes ofother types can be added to the system and will also act as repeaters if they support this function of repeating the signalreceived to other modules in the system.As part of a HomePro network, the ZDP100 can act as a wireless repeater to insure that commands intended foranother device in the network are received. This is useful when the device would otherwise be out of the radio rangeof the wireless controller.There are no field repairable assemblies on this unit. It is covered by a one year limited warranty. If service is needed,the unit must be returned where purchased.INSTALLATIONPlug this Lamp Module into the wall outlet near the lamp to be controlled, and plug the lamp into the Lamp Module.See the ZTH100 Wireless Controller operating instructions to add this module under the command of the WirelessController. Make sure the lamp(s) to be controlled total no more than 300 watts. WARNING: Plugging a non-resistiveload such as florescent lighting or a device with a motor may result in damage to the Lamp Module and will void thewarranty.Lamp Module ButtonThe Lamp Module has a button on the face (see picture above) that switches an attached lamp ON and OFF, andadjusts its dimming level by holding it down, and it is also used to configure the module to operate from the wirelesscontroller. With the Wireless Controller, the Lamp Module can be switched ON and OFF, and can be includedin groups of lights (a group can also be a single module) that operate at the same time, and in scenes that set alighting mood.Switch power ON and OFF locallyWhen the button is pressed and released quickly, the power will toggle. This means that power will be turned OFFif it was ON and turned ON if it was OFF. When switching the Lamp Module ON or OFF, the light will dim UP (orDOWN) in approximately 2 seconds until the final level is reached.DimmingIf the button is constantly pressed the light will be dimmed. The dimming function will also toggle. Constantlypressing the button the Lamp Module will dim either UP or DOWN until it reaches the maximum or minimum value.The second time the button is held down, the dimming will change direction. When the power level reaches eitherfull power or minimum power the dimming will stop until the button has been released and is pressed again.
ZDP100 Instructions101002HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0607-012Child ProtectionThe Lamp Module can be set in a child protect mode by the Wireless Controller. When this mode is active, a userwill have to press the button on the Lamp Module 3 times rapidly to activate the attached load. The module operatesnormally when controlled by the Wireless Controller..Other functionsThe button on the Lamp Module also plays a role as a reset in addition to adding module to groups and scenes.This is described in more detail in the Wireless Controller instructions.Software fuseThis Lamp Module is designed to protect itself against loads that exceed it’s maximum power rating. Theapplication of a load that exceeds that rating is quickly sensed by the dimmer and it responds by immediatelyshutting off all power to that load.If the dimmer doesn’t seem to work, or if it only works momentarily, check to see that the total lamp wattage doesn’texceed the 300W rating of the Lamp Module. If a properly sized load is restored to the dimmer, it can be operatednormally once again.Over-current protectionThe Lamp Module hardware has an over current detection circuit, which is final protection against overload.If the software fuse should fail to shut down the dimmer when overloaded, backup protection is provided by aninternal fuse. This fuse is not user serviceable. Check your home circuit breakers before concluding that theproduct must be returned to manufacturer for repair at a nominal charge.Operation NoteWhen a light bulb reaches the end of it’s life and burns out, it sometimes creates a momentary short circuit. Thehigh current that results may cause the dimmer to properly respond by turning off. Should this happen, replacethe bulb with a new one. The dimmer can now be operated to restore power to the light.WARRANTYAdvanced Control Technologies, Inc. gives this expressed warranty (along with extended warranty endorsements, where applicable) in lieuof all other warranties, express or implied, including (without limitation), warranties of merchantability and fitness for a particular purpose.This constitutes Advanced Control Technologies, Inc.’s sole warranty and obligation with regard to our products as well as the Customer’ssole remedy.Advanced Control Technologies, Inc. expressly disclaims all liability and responsibility for any special, indirect or consequential damagesor any further loss of any kind whatsoever resulting from the use of our product. The Customer’s sole and exclusive remedy and the limitof Advanced Control Technologies, Inc.’s liability for any loss whatsoever, shall not exceed the purchase price paid by the Customer for theproduct to which a claim is made.Some states do not allow limitations of incidental or consequential damages or on how long an implied warranty lasts, so the above limitationsmay not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.All products manufactured by Advanced Control Technologies, Inc. are warranted to be free from defects in material and workmanship inaccordance with and subject to the following terms and conditions:1. This warranty is limited to the original Customer only. It cannot be transferred or assigned to third parties unless the intent totransfer to a third party is expressly indicated in a purchase order and/or warranty processing arrangements have been agreedupon in writing by Advanced Control Technologies, Inc.2. Advanced Control Technologies, Inc. will correct any defects in material or workmanship which appear within one (1) year from thedate of purchase. Advanced Control Technologies, Inc. will repair or replace, at our option, any defective products, provided thatour inspection discloses that such defects developed under normal and proper use. This warranty does not extend to goodssubjected to misuse, neglect, accident or improper installation, or to maintenance or repair of products which have been altered orrepaired by anyone except Advanced Control Technologies, Inc. unless otherwise stated in writing.3. An appropriate charge (50% of product list price) will be made for testing, repairs, replacement and shipping for returned productwhich is not defective or found to be defective as the result of improper use, maintenance or neglect.4. Information in our descriptive literature is based on product specifications that are current at the time of publication. Productspecifications, designs and descriptive literature are subject to change as improvements are introduced. Although we announcechanges as they occur, we cannot guarantee notification to every Customer. Advanced Control Technologies, Inc. warrantsdelivered product to conform to the most current specifications, designs and descriptive literature.
ZDP100 Instructions101002HomeProby ADVANCED CONTROL TECHNOLOGIES, INC.0607-013FCC NOTICENote: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions may cause harmfulinterference to radio communications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.IC NOTICEThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) thisdevice must accept any interference, including interference that may cause undesired operation of thedevice.Power 120 VAC, 60 HzSignal (Frequency) 908.42 MHzMaximum Load 300 W, for incandescent lamps onlyRange Up to 100 feet line of sight between the Wireless Controller and /or theclosest HomePro plug-In Lamp Module or Appliance Module

Navigation menu