Advanced Card Systems ACR900 Banking POS Terminal User Manual

Advanced Card Systems Limited Banking POS Terminal Users Manual

Users Manual

ACR900 POS Terminal User Manual I. Installation 1. SAM cards / SIM card / Micro SD card Unclip the trapdoor on the bottom the terminal by your nails. Insert SAM cards / SIM card / Micro SD card to the related card slots. Close the trapdoor. 2. Rechargeable Battery Unclip the trapdoor on the bottom Place the battery over the SAM card and SIM card slot.battery would touch with the metal contactClose the trapdoor. 3. Charging the battery Connect the 9V DC power supply provided together with ACR900 to the power port on ACR900. 4. Paper roll Lift the tab on the printer cover open the paper compartment. Place a paper roll (diameter not over 37mm) in the compartment Press simultaneously on both upper corners of the printer cover until it clips into position. 5. Connecting to Ethernet, USB devices and Serial devices Connect the ACR900 to the interface module with the specific cable provided together with ACR900. Connect the Ethernet cable, USB cable or Serial cable to the specific port on the interface module ACR900 POS Terminal User Manual1. SAM cards / SIM card / Micro SD card the bottom side of Insert SAM cards / SIM card / Micro SD the bottom side of the terminal by your nails. Place the battery over the SAM card and SIM card slot. Make sure that metal plates on the battery would touch with the metal contacts in the battery case of terminal. Connect the 9V DC power supply provided together with ACR900 to the power port on to paper roll (diameter not in the compartment upper corners of the printer cover Connecting to Ethernet, USB devices and Serial interface module with the specific cable provided together with ACR900. Connect the Ethernet cable, USB cable or Serial cable to the specific port on the interface module ACR900 POS Terminal User Manual Make sure that metal plates on the
II. Operating instruction 1. Turn ON / OFF Press button for 3 seconds to Turn ON. Press button for 3 seconds until the LCD shows Turn OFF confirm page; Press button (enter key) to confirm Turn OFF. 2. Sleep / Wake Press button and LCD turns off. Press button again to turn LCD on. 3. Reading Smart Card (contact) Insert the card horizontally with chip facing upward until the card reaches the end in the card slot. Leave the card in the card slot throughout a transaction. 4. Reading Smart Card (contactless) Tap the card firmly in the active zone over the printer cover. Keep the card close to the zone during a transaction. 5. Reading Magnetic Stripe Card Swipe the card with the stripe facing to the terminal either from top to bottom or bottom to top. Use a regular movement inside the track. 6. Feeding paper Press button to feed paper. DO NOT pull the paper by hand. 7. Tearing the printing paper Pull the receipt against the printer cutter at an angle either from left to right or from right to left. III. Caution Never disassemble the terminal without approval. Only use the power supply included with the terminal or provided by ACS Turn off the terminal before opening the trapdoor. Avoid the terminal contact with water.
IV. Rechargeable Battery Only use the rechargeable battery provided together with the terminal or provided by ACS. Avoid placing the battery directly under the sun, or environment of high temperature or high humidity. Do not short-circuit the battery Do not disassemble the battery FCCCaution.Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.AnyChangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:‐Reorientorrelocatethereceivingantenna.‐Increasetheseparationbetweentheequipmentandreceiver.‐Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp. FCC Radiation Exposure Statement: Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the Bank ing P OS Terminal transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the Bank ing P OS Terminal while operating can be well below the maximum value. Before a new model Bank ing P OS Terminal is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, tests for each Banki ing P OS Terminal are performed in positions and locations as required by the FCC. For body worn operation, this model Banki ing P OS Terminal has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal.

Navigation menu