Advance Security TR74 TRE901AM User Manual

Advance Security Inc TRE901AM Users Manual

Users Manual

Dome Light Delay / Theater Dimming The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the dome light delay and add 2 seconds before arming. 1. Close all doors with ignition off. 2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK. The LED will light solid to indicate the system has entered DOME DELAY LEARN MODE. 3. Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the learning mode.  4. TheLEDwillbegintoashindicatingthesystemhasexitedthe  learning mode and is now armed. Defaulting the Dome Light Delay: Turn the ignition ON then OFF 3 times then press and hold the valet button for 5 seconds, the system will chirp 1 time indicating the learned delay time has been cleared. User Selectable LED This feature will control whether the LED is ON or OFF when the system is Armed/Locked.ThiswillbeselectableinfeatureprogrammingORon-the-ywithoutenteringthe programming feature banks. 1. Turn the ignition ON, OFF, ON, OFF. 2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.PROFESSIONALSERIESSecurity and Remote Start Installation Quick Reference GuidecaSECRS2017 Voxx Electronics Corporation. All rights reserved. Adjusting the Shock Sensor 1. Increase sensitivity by turning the adjustment dial clockwise. 2. Decrease sensitivity by turning the adjustment dial counter clockwise. Tach Programming The unit will not operate unless tach is programmed or a tachless option is turned ON.Ifanattemptismadetostartthevehicleviatheremotestartwithoutrstprogrammingtach,theunitwillashtheparkinglights7timesindicatingtachhasnotbeenlearnedandstored.Ifthetachrateisnotproperlyprogrammedtothespecicvehicle, the unit may not realize that the vehicle is running in certain instances and re-engage the starter motor. The Remote Start unit will learn the tach rate of most vehicle’s single coil, multiple coil packs, or single injector. To learn tach: 1. Turn the ignition key to the ON position. 2. Press and release the valet/override button 3 times. 3. Immediately turn the ignition key OFF. 4. Press and hold the valet/override button, then start the vehicle using the key. 5. When the unit senses the tach signal, the parking lights will begin to   ash. 6. Allow the vehicle to settle to a normal idle speed. 7. Release the valet/program push-button switch. The parking lights will turn on for 2 seconds and 1 long chip will indicate that the learned tach signal is stored and the unit has exited tach learn mode. NOTE: If the unit fails to learn tach rate due to an improper tach connection or a poortachsource,theparkinglightswillnotash.Tocorrectthissituation,locateandconnect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach learn routine. Smart Tachless Mode Smart Tachless Mode is available only if a tach signal has never been learned to the system and when activated will automatically change the Tach Mode feature in option programming to Tachless without the need to enter the feature programming mode.   1. Activatetheremotestart.Theparkinglightsshouldbeginashing7 times indicating no tach signal has been learned.   2. Withinthe7ashtimeperiod,pressandholdthe button. 3. The system will chirp 1 time indicating the system is now in tachless mode. Chirp Delete - User Accessible System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks. 1. Turn the ignition ON then OFF. 2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.RED BATTERY 12V ( + ) BLACK GROUND WHEN ARMED ( - )BLUE FULL TRIGGER ( - )GREEN WARN AWAY TRIGGER ( - )SHOCK SENSOR & HARNESSReplacement Part #4700023ORANGE 86 - ARMED OUTPUT ( - )RED 85 - IGNITION ( + )BLACK 87A - STARTER OUTPUT - MOTOR SIDEWHITE / BLACK 30 - STARTER INPUT - KEY SIDEOPEN 87 - OPENSTARTER INTERUPT RELAY & HARNESS86 85308787aReplacement Part #1024405DBI PORTSHOCK SENSOR PORTTELEMATICS PORTBLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )PURPLE/WHITE TACH INPUTGRAY/RED PARKING BRAKE INPUT ( - )GREEN DOOR TRIGGER INPUT ( - )BLUE/WHITE INSTANT TRIGGER INPUT ( - )WHITE/BLUE EXTERNAL START INPUT ( - )PURPLE DOOR TRIGGER INPUT ( + )BROWN/RED BRAKE INPUT ( + )GRAY HOOD INPUT ( - )PINK/BLACK AUX 5 OUTPUT ( - )GRAY/BLACK AUX 3 OUTPUT ( - )ORANGE GROUND WHEN ARMED ( - )VIOLET/BLACK AUX 1 OUTPUT ( - )RED/WHITE TRUNK RELEASE OUTPUT ( - )BROWN/BLACK HORN OUTPUT ( - )LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )LT BLUE FACTORY ARM / PULSE AFTER START ( - )GREEN/WHITE PULSE AFTER SHUTDOWN ( - )BLACK/YELLOW PULSE DURING CRANK ( - )BLUE/GREEN FACTORY DISARM 2 / 2ND UNLOCK ( - )ORANGE/BLACK AUX 4 OUTPUT ( - )WHITE/BLACK AUX 2 OUTPUT ( - )#4120389WHITE/RED PARKING LIGHT INPUTWHITE PARKING LIGHT OUTPUTBLACK GROUNDBROWN SIREN OUTPUT ( + )#4120145BLUE UNLOCK ( - )OPENGREEN LOCK ( - ) #1031423CASECRS# 4360698FLCART PROGRAMMING PORTFLCART PORTFLCART HARNESS PORTPINK IGNITION 1 ( + )RED BATTERY 12V ( + )PINK/WHITE IGNITION 2 ( + )ORANGE ACCESSORY 1 ( + )RED/WHITE BATTERY 12V ( + )PURPLE STARTER OUTPUT - MOTOR SIDE ( + )# 4120110Replacement PartReplacement PartReplacement PartRemote Start / Power Harness (6-Pin)Replacement PartReplacement PartNotification Harness (4-Pin)Input / OutputHarness (22-Pin)Door Lock Harness (3-Pin)ANTENNALEDVALET** RF KITS SOLD SEPERATELY **Replacement Parts1-Way # 41800652-Way # 4180064Harness (4-Pin) # 4120388 ANTENNA PORTPPPPPPPPPPPPPPPPPProgramming Note:PThe default wire function settings are listed nextto the wire color. Wires shown with can be programmed to perform different functions. Refer to the Feature Programming section to change the default setting.P Security Trigger Zones IfthesecuritysystemhasbeentriggeredtheLEDwillashoneofthepatternsbelowindicating the zone. LED FLASHES TRIGGER ZONE 2 Flashes Hood / Trunk Input 3 Flashes Door Input 4 Flashes Shock Sensor 5 Flashes Ignition Input Remote Start Shutdown Diagnostics Iftheremotestartshutsdownorfailstostart,theparkinglightswillashoneofthepatternsbelowindicatingtheshutdowninput. To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button. PARKING LIGHT FLASHES SHUTDOWN ZONE 3 Flashes Hood / Brake Input 4 Flashes Remote Start Valet Mode 5 Flashes Manual Transmission Mode not ready 7 Flashes Tach not learned / Crank Average not learned Complete guides also available at www.voxxuniversity.com
Defaulting All Features: Pressing the button anytime while in any of the feature banks will default all features and return you to feature bank 2 - 4 chirps.NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.Manual Feature Programming - Feature Bank 2, 3, 4, & 51. Turn the ignition ON.2. Press and hold the valet/override button.3. Within 10 seconds the system will chirp (3) three times.4. Use the valet/override button to advance through each option bank. Forfeature programming advance to Feature Bank 2, 3, 4 or 5, which is (4)four,(5)ve,(6)sixand(7)sevenchirps.5. Use the transmitter button to scroll through the selections in eachfeature bank, the system will chirp to match the feature number.6. Press the transmitter button or the vehicle brake pedal to change thedesiredfeature.TheLEDwillashindicatingthechangedfeature.Set Up & ProgrammingTransmitter Programming - Feature Bank 11. Turn the ignition ON.2. Press and hold the valet/override button.3. Within 10 seconds the system will chirp (3) three times.4. Press 1 button of each transmitter you wish to program.5. The system will respond with 1 chirp for each accepted transmitter.6. Pressing the override button at anytime during programming will advance tothe next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity.NOTE: This system has 1 button programming which programs all channels of the system. NOTE: The system will hold up to 4 transmitters in memory, programming a 5th transmitter will erase the oldest transmitter in memory. NOTE:ThissystemhasPTN-ProgrammedTransmitterNotication.EachtimetheignitionisturnedON,theLEDwillashthenumberoftransmittersprogrammedtothesystem. Transmitter programming for 2 Car Mode *2 way LCD system only:1. Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in theowners manual for 2 car operation)2. Follow the steps above for transmitter programming.NOTE: 2 car mode requires an additional security system installed in a second vehicle.Refer to transmitter programming.Feature Ba nk 1 - 3 ChirpsTransm itter Programming Feature Bank 2 - 4 ChirpsSecurity Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 1Silent Choice ON OFF2Door Locks Active Passive3System ArmingActive Passive4System Notifications Siren & Horn Siren Only Horn Only5Alarm Duration 30 Seconds 60 Seconds6SecurityON OFFON w/ OEM Remote Start7Anti-Hijack Mode OFFON8Ground While ArmedOrange ( - ) OutputGround While ArmedGround While Disarmed9DBI Port Protocol / Telematic Port ProtocolDBI /Voxx TelematicADS /Voxx TelematicDBI / ADS TelematicADS / ADS Telematic10 Arm / Disarm ChirpsStandard: 2 - Arm1 - Disa rmInve rted:1 - Arm2 - Disarm11 LED IndicatorON OFF12 Auto Re-lock OFFLock Only Arm & Lock13 Extended Parking Lights OFF After Unlock After Lock After Lock & Unlock14 Parking Light Relay / Trunk ( - ) Output Standard InvertedFeature Bank 3 - 5 ChirpsOutput Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 1Lock / Unlock Timing 1 Sec. 3.5 Sec. 1 Sec. Lock, 2x Unlock 30 Sec. Lock, 2x Unlock 2x Lock, 1 Sec. Unlock 0.5 Sec. 2Factory Disarm 2Blue / Green OutputFactory Disa rm 2nd Unlock Factory Disarm2x 500mS Factory Disarm350mSFactory Disarm500mSFactory Disarm w/ Unlock Timing3Ignition Locks OFFLock / Unlock Lock Only Unlock Only 4Trunk Output Timing1 Sec. 10 Sec.20 Sec. Latched until IGN ONLatched ON until Button Press5Horn Output Timing16mS 10mS 30mS 40mS 50mS6Real PanicON OFF7AUX 1Violet / Black Output 1 Sec. LatchedLatched until IGN ONDome Light OutputDefrost Output Single Pulse After Start Defrost Output Latched 5 Min After Start8AUX 2White / Black Output 1 Sec. LatchedLatched until IGN ON10 Sec. w/ Arm10 Sec. w/ Disarm9AUX 3Gray / Black Output 1 Sec. LatchedLatched until IGN ON10 Sec. w/ Arm10 Sec. w/ Disarm10 AUX 4Orange / Black Output 1 Sec. LatchedLatched until IGN ON10 Sec. w/ Arm10 Sec. w/ Disarm11 AUX 5Pink / Black Output 1 Sec. LatchedLatched until IGN ON10 Sec. w/ Arm10 Sec. w/ DisarmFeature Bank 4 - 6 ChirpsRemote Sta rt Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 1RS Confirmation Chirp ON OFF2Run Time 15 Minutes5 Minutes10 Minutes20 Minutes45 Minutes60 Minutes3Running LightsSteady Flashing4Tach Mode Tach TachlessHybridDBI Port5Voltage Level High Low6Crank Time 1.0 Seconds 0.8 Seconds 1.5 Seconds 2.0 Seconds 4.0 Seconds7Crank Output Averaging Preset Time8Diesel DelayOFF 10 Sec. Delay 15 Sec. Delay 20 Sec. Delay 45 Sec. Delay9Remote Start Activa tion 2x Sta rt 1x Start10 Ignition 2 OutputPink / White Ignition Accessory Start / Crank11 Auto Start Interval3 Hour 2 Hour12 Turbo TimerOFF1 Minute 3 Minute5 Minute13 Transmission Mode AutomaticManual14 Temperature StartOFF14F5F-4F15 Accessory OutputOrange Accessory Ignition Start / Crank16 Pulse Outputs with UnlockOFFIGN, ACCY, GWRIGN, ACCY, GWR - Pulse After Shutdown17 RS Door Lock ControlOFFUnlock before Start, Lock After StartUnlock Before StartLock After StartLock After ShutdownFeature Ba nk 5 - 7 ChirpsAlternate Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 1Factory DisarmLt Green / Black OutputPulse Before Start / During UnlockGround While RunningIgnition Accessory Pulse During CrankPulse Before Start / During Unlock - Uses Unlock Timing2Factory ArmLt Blue OutputPulse After Start / During LockGround While RunningIgnition Accessory Pulse During CrankPulse After Start / During Lock - Uses Lock Timing3Pulse After ShutdownGreen / White OutputPulse After ShutdownGround While RunningIgnition Accessory Pulse During CrankPulse After Shutdown 2 Sec. Delay4Pulse During CrankBlack / Yellow OutputPulse During CrankGround While RunningIgnition AccessoryPulse Before Start / During UnlockPulse Before Start / During Unlock - Uses Unlock TimingPC Based Feature Programming / Firmware UpdatesWhenusingtheNEWCodeAlarmUtilityAppalongwithaVEPROGProgrammingtoolyoumayprogramselectablefeaturesorupdatethermwareofthismodule.Refertofullinstallation guide for additional detail.1. To download the Code Alarm Utility App visit the Voxx University website at voxxuniversity.com (registration/login required).2. Select VOXXTECH and locate the utility app under the heading Software Downloads.3. The Code Alarm Utility App download includes both the CA Utility app and necessary VEPROG drivers.4. Install both items before attempting to update modules.Technical Support (800) 421-3209or visitwww.voxxuniversity.comFeature Bank 2, Programming Update Notice: Firmware version 3.0 or later. Feature #9 has been updated to DBI Port Protocol & Telematic Port Protocol which now includes a selection for the telematic port protocol. The new default setting of DBI / ADS Telematic is the correct protocol setting for the ASCL6 CarLink device.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.FCC Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu