Ademco 8DL5820L Door / Window Contact Transmitter User Manual

Honeywell International Inc. Door / Window Contact Transmitter Users Manual

Users Manual

AdemcoK9230V35820L Exterior of boxFile: K9230V3_Blueline_Ademco_5820L_instruct_exterior.epsASSEMBLED IN MEXICO© 2009 Honeywell International Inc.All Rights ReservedLong Life Battery IncludedADEMCO 5820LSee inside of carton forInstallation Instructions Slim Line TransmitterSlim Line TransmitterADEMCO 5820LSlim Line Transmitter7/11 K9230V3ADEMCO 5820LSlim Line TransmitterADEMCO 5820L<<< Open Carton Along Perforations >>>Perforation (1/4" x 1/8")Ideal for casement anddouble hung windowsRRLITHIUMLITHIUMADEMCO 5820LSlim Line TransmitterFEDERAL COMMUNICATIONS COMMISSION STATEMENTS: The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.+MOUNTINGHOLEMOUNTINGHOLETAMPERPROTECTIONBATTERY(1.5VDC, AAALITHIUM.SEE NOTEINSIDE.)TAMPERSWITCHSleek design is nearly half the size of competitors Easy to open case requires no special toolsCase tamper protection (front and back)Ideal for double-hung windowsEasy replaceable AAA lithium batterySleek design is nearly half the size of competitors Easy to open case requires no special toolsCase tamper protection (front and back)Ideal for double-hung windowsEasy replaceable AAA lithium batteryFront and back-case tamper isprovided using the same switch.The front-case tamper is alwaysenabled. Adding the third screwas shown in the figure enablesthe back-case tamper.Tamper ProtectionN219ÊK9230V3HŠ
AdemcoK9230V35820L Interior of boxFile: K9230V3_Blueline_Ademco_5820L_instruct_interior.epsBattery InformationNOTEFOR DOCUMENTATION AND ONLINE SUPPORThttp://www.security.honeywell.com/hsc/resources/MyWebTechFOR WARRANTY INFORMATION GO TO:http://www.security.honeywell.com/hsc/resources/waSee inside ofcarton forinstallationinstructions.See inside ofcarton forinstallationinstructions.REFER TO THE INSTALLATIONINSTRUCTIONS FOR THE CONTROLWITH WHICH THIS DEVICE IS USED,FOR DETAILS REGARDINGLIMITATIONS OF THE ENTIREALARM SYSTEM.1.2.3.5820L is a single-zone Slim-LineDoor/Window contact transmitterthat provides wireless notificationof intrusion.Install mounting screwsin the two outsidemounting holes asshown in the diagramusing a #1 Phillips.If the case-back tamperswitch will be used,install a third screw inthe middle hole.Mount the magnet(supplied) adjacent tothe two verticalpositioning lines on thecase side (see diagram).The gap can be one-halfof an inch maximum.To reinstall the cover,position the cover sothat it covers themounted case-back, andsnap-shut. The two casehalves can only be fittedtogether in one direction.Temporarily mount the 5820Land magnet using the double-back tape provided.If the Go/No Go test wassuccessful, remove thetransmitters cover by insertingthe flat blade of a small screw-driver into the opening slot atone end of the unit as shownin the diagram and separate thetwo halves.The 5820L must only bemounted against a flat surface.A curved surface would causeundo stress to the unit andpossible failure to operateproperly.4.5.6.7.Before mounting permanentlyusing the double-back tape ormounting screws, conduct aGo/No Go test to verify adequatesignal strength and reorient orrelocate the transmitter if necessaryNOTEInstallationAlkaline Battery Will Yield LessBattery Life than LithiumReplace battery only with:Energizer L92 AAA Lithium orAAA Alkaline, Duracell MX2400,Panasonic AM-4PI,Eveready Engeriger EN92.BATTERY CAUTION: Risk of fire,explosion and burns. Do notrecharge, disassemble, heat above212 F (100 C) or incinerate.Dispose of used batteries properly.Keep away from children.Perforation (1/4 x 1/8)MAGNETOPENINGSLOTGAP 0.5" MAXMAGNET ALIGNMENTLOCATORSDo NOT attempt to removethe PCB from the plasticcover for any reason.NOTEDuring the programming of thecontrol panel transmitter must beenrolled as Input Type 3,Supervised RF), Loop 1.NOTEObserve correct polarity.FCC / IC Statement:This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable.
K9232V2 7/11 Rev. A ADEMCO 5820L Door/Window Contact TransmitterDoor/Window Contact TransmitterDoor/Window Contact TransmitterDoor/Window Contact Transmitter INSTALLATION AND SETUP GUIDE GENERAL INFORMATION The 5820L is a single-zone Slim-Line Door/Window contact transmitter that provides wireless notification of intrusion. The 5820L can be used only with alarm systems that support 5800 Series wireless devices. The 5820L has its own unique serial number permanently assigned during manufacture. You must enroll the transmitter’s serial number in the control panel before it will operate in the system. Refer to the control panel’s installation instructions for programming details. Note: During programming of the control panel, 5820L transmitters must be enrolled as Input Type 3 (Supervised RF), Loop 1. The transmitter is powered by one AAA Lithium (or alkaline) battery that is easily replaced when a low battery condition is indicated by the control panel. TAMPER PROTECTION Front and back-case tamper is provided using the same switch. The front-case tamper is always enabled. Adding the third screw as shown in Figure 2 enables the back-case tamper. MAGNETOPENINGSLOTGAP 0.5" MAX5820-001-V0MAGNET ALIGNMENTLOCATORS Figure 1. 5820L (Typical Installation Arrangement) +MOUNTINGHOLEMOUNTINGHOLETAMPERPROTECTION5820-002-V1BATTERY(1.5VDC, AAALITHIUM ORALKALINE)TAMPERSWITCH Figure 2. 5820L Mounting/Battery Location MOUNTING The description that follows assumes that the transmitter will be mounted as shown in Figure 1, with the magnet located adjacent to the unit's left side. The transmitter may, however, be installed in any direction, as long as the relationship of the unit to the magnet is maintained as shown in Figure 1. 1. Temporarily mount the 5820L and magnet using the double-back tape supplied. Note: Before mounting the transmitter and magnet permanently using the double-back tape or mounting screws, conduct a Go/No Go test (see control's instructions) to verify adequate signal strength and reorient or relocate the transmitter if necessary. 2. If the Go/No Go test was successful, remove the transmitter's cover by inserting the flat blade of a small screwdriver into the opening slot at one end of the unit as shown in Figure 1, and separating the two halves. 3. The 5820L must only be mounted against a flat surface. A curved surface would cause undue stress to the unit and possible failure to operate properly. 4. Install mounting screws in the two outside mounting holes as shown in Figure 2 using a #1 Phillips. 5. If the case-back tamper switch will be used, install a third screw in the middle hole. 6. Mount the magnet (supplied) adjacent to the two vertical positioning lines on the case side (see Figure 1). The gap can be one-half an inch maximum. 7. To reinstall the cover, position the cover so that it covers the mounted case-back, and snap-shut. The two case halves can only be fitted together in one direction. Note: Do NOT attempt to remove the PCB from the plastic cover for any reason. BATTERY INSTALLATION/REPLACEMENT Replace battery only with same or equivalent type. Dispose of used batteries according to the battery manufacturer’s instruction. 1. Remove the transmitter's cover (if it is not off already) as described in Mounting; step 2. 2. Observe correct polarity and insert the battery provided into the battery retainer clips as shown in Figure 2. Note: Replace battery only with type specified in the Specifications paragraph.
SPECIFICATIONS Dimensions: ...................... 3.0” H x 0.5” W x 0.8” D 76.2mm x 12.7mm x 20.3mm Battery: ...... 1.5VDC, AAA Lithium (Energizer L92) or AAA Alkaline, (Duracell MX2400, Panasonic AM-4PI, Eveready Energizer EN92) Gap: ......................................... 0.5 inch maximum Magnet: ...........................WA5816MAG (supplied) BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Dispose of used batteries properly. Keep away from children. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2), this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable. FEDERAL COMMUNICATIONS COMMISSION STATEMENT: The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. For the latest warranty information, please go to: http://www.security.honeywell.com/hsc/resources/wa ÊK9232V2KŠ K9232V2 7/11 Rev. A 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright 2008 Honeywell International Inc. http://www.honeywell.com/security

Navigation menu