Ademco 8DL5808AP Photoelectronic Smoke/Heat Detector User Manual I56 918 14R indd

Honeywell International Inc. Photoelectronic Smoke/Heat Detector I56 918 14R indd

Contents

Users Manual Part 2 Revised

CAUTIONDO NOT attach the detector to removable ceiling panels. Attach the detector across panel support as shown in Figure 3.TAMPER PROTECTIONThis detector has a built-in tamper switch that will cause a CHECK signal to be displayed at the console of the detector if it is removed from its installation bracket. The mounting bracket can also be made tamperproof by breaking off the smaller tab at the scribed line (see Figure 2), thus preventing removal of the detector without a tool. To remove the detector, use a small screwdriver to depress the tamperproof tab and turn the detector counterclockwise.TESTINGNOTE: Before testing, notify the proper authorities that the smoke detector system is undergoing maintenance and will temporarily be out of ser-vice. Disable the zone or system undergoing maintenance to prevent unwanted alarms.Detectors must be tested after installation and following periodic maintenance. The 5808LST may be tested as follows:A. TEST SWITCH 1. A recessed test switch is located on the detector housing. 2. Push and hold the recessed test switch for a minimum of 5 seconds. Use a small screwdriver or allen key maximum diameter of .18” (The alarm panel will trigger and then the smoke detector will go into alarm. If the tool is removed from the recessed switch the sounder will shut off.) 3. The LED on the detector should blink once per second and the horn should sound within 3 seconds.B. SMOKE ENTRY TEST Hold a smoldering punk stick or cotton wick at the side of the detector and gently blow smoke through the detector until the unit alarms.C. DIRECT HEAT METHOD (Hair dryer of 1000-1500 watts) Direct the heat toward either side thermistor. Be sure to hold the heat source about 12 inches from the detector to avoid damage to the plastic. The detector will reset only after it has time to cool.Smoke detection testing is recommended for verifying system protection capability.A detector that fails to activate with any of these tests should first be cleaned as outlined in this manual’s MAINTENANCE section. If the detector still fails to activate, return for repair.Notify the proper authorities that the system is back on line.TESTING TRANSMITTER SIGNALNOTE: Remove battery tab before installation. This test should be performed before installation to determine a strong com-munication path with the control panel and after installation is complete. Also, the owner/user should test the unit at least weekly.1. Activate the wireless system’s TEST mode from the console.2. Depress and hold the smoke detector’s TEST switch and the detector should immediately transmit an alarm signal to the control panel. The built-in horn will start to sound about 2.5 seconds after depressing the button.3. The wireless system’s console should emit at least 3 audible sounds when the alarm transmission is received and will display the transmitting detector’s ID number.4. When the console has received the test signal, release the TEST switch. The horn will immediately stop and a few seconds later the detector’s ID number will clear from the console display.5. If the console does not respond as noted, check the polarity of the batter-ies and be sure they are fresh. If this is an initial installation, try moving the detector to another location that provides proper reception. Also be sure that the detector’s ID has been “enrolled” by the control panel (see PROGRAMMING). Then, repeat the test.6. Turn off the system’s TEST mode from the console (security code + OFF).CAUTIONSmoke detectors are not to be used with detector guards unless the combina-tion has been evaluated and found suitable for that purpose.WHAT TO DO IN CASE OF FIRE1. DON’T PANIC — escape may depend on clear thinking.2. Get out of the house following the planned escape routes, if possible. Do not stop to dress or to collect anything.3. Open doors carefully only after feeling them to see if they are hot. If a door is hot, do not open it— follow an alternate escape route.4. Keep close to the floor — smoke and hot gases rise. Breathe through a cloth (wet, if possible) and take short shallow breaths.5. Keep doors and windows closed unless it is necessary to open them for escape. 6. Meet at your meeting place after leaving your home.7. Call the local fire department as soon as possible from outside the home.8. Never re-enter a burning building.For more information about fire safety, contact your local fire department. They can supply more detailed information about making your home as free from fire hazards as possible and about planning for escape in case of fire.MOUNTINGFirst, determine the best location for the smoke detector; a location that pro-vides strong wireless transmission paths and proper smoke detection. A GOOD TRANSMISSION PATH MUST BE ESTABLISHED FROM THE PROPOSED MOUNTING LOCATION BEFORE PERMANENTLY INSTALLING THE DETECTOR. To check, perform the test described in the TESTING TRANSMITTER SIGNAL section of this manual. To mount the detector:1. Once a suitable location has been determined, install the mounting bracket on the ceiling or on the wall (if local ordinances permit). Use the two screws and anchors provided.2. Prior to mounting the detector to the mounting bracket, the system must “enroll” the detector’s ID. See the PROGRAMMING section for the steps to follow.3. Turn the detector in a clockwise direction in the mounting bracket until it clicks into place.4. Test the detector immediately after completing the installation (as described in the TESTING section of this manual) and refer to the control system’s instructions for additional information concerning the use of wireless smoke detectors. TAMPER SLOT(DEPRESS TAB TOREMOVE DETECTOR)TAMPER RESISTANT TAB (CUT OFF SMALL TAB TO ACTIVATE TAMPER-RESIST FEATURE)ALIGNMENTARROWSS0158-00Figure 2. Detector Mounting BracketS0162-00Figure 3. Mount Detector Across Ceiling Panel SupportAD300-00-00 3 I56-918-14R
AD300-00-00 4 I56-918-14R©2005 HoneywellLIMITED WARRANTYHoneywell International Inc., acting through its Security & Custom Electronics business (“Seller”) 165 Eileen Way, Syosset, New York 11791, warrants its product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product(s) or, for product(s) not having a manufacturer’s date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller’s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product(s) which is proved not in compliance with Seller’s specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER’S OWN NEGLIGENCE OR FAULT.Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product(s) will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result.CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER.USER CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.FCC ID: CFS8DL5808APFCC PART 15 STATEMENTThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Smoke detectors shall be replaced after being in service for 10 years. However, any smoke detector, fire alarm equipment, or any component of that system which fails prior to that shall be repaired or replaced as soon as possible. Batteries shall be replaced upon indication of a pre-low battery condition.MAINTENANCENOTE: Before removing the detector, notify the proper authorities that the smoke detector system is undergoing maintenance and will be tem-porarily out of service. Disable the zone or system undergoing mainte-nance to prevent unwanted alarms.NOTE: Before removing the detector cover, note the position of the thermis-tors. Make sure the thermistors are not bent over when the housing is replaced.1. Remove the detector housing by gently prying the four housing tabs on the bottom of the base with a small-bladed screwdriver and pull the housing from the base. Use caution to avoid damaging the thermistors. 2. Vacuum the screen carefully without removing it.3. Remove screen assembly, pulling straight out (please see Figure 4).4. Remove the sensing chamber cover.5. Clean the sensing chamber by vacuuming or blowing out dust and particles.6. Replace the sensing chamber cover, aligning the arrow on the cover top with the arrow on the printed circuit board.7. Replace the screen by placing the screen assembly over the sensing chamber cover and twisting until it snaps into place.8. Replace the housing by aligning the two triangular slots on the base with their counterparts on the housing. Gently press the housing until it locks in place. Check to make sure that the ther- mistors are in the upright position.9. Reinstall the detector.10. Notify the proper authorities that the system is back in operation.REMOVABLEHOUSINGBASEREMOVABLESCREENSENSINGCHAMBER COVERSENSINGCHAMBERS0163-00Figure 4. Removal of Cover and Screen for Cleaning Please refer to insert for the Limitations of Fire Alarm Systems

Navigation menu