Ademco 8DL5800PIRESAP Wireless Motion Sensor User Manual 800 13192 A 5800PIRRES AP ii

Honeywell International Inc. Wireless Motion Sensor 800 13192 A 5800PIRRES AP ii

Users Manual

5800PIRRES-AP Wireless Motion Sensor - Installation Instructions PRELIMINARY DRAFT 8/24/09 - 1 - CONNECT THE BATTERY, ENROLL THE SENSOR, CONDUCT GO / NO GO TEST, AND PERFORM WALK TEST / METTRE LES PILES EN PLACE , ENROLL THE SENSOR, CONDUCT GO / NO GO TEST, AND PERFORM WALK TESTACCESSORIES / ACCESSOIRESTOPOPEN / OUVERTURE LOCATION / EMPLACEMENT 127.5 - 8 ftMOUNT / INSTALLATION 432Recommended Screws: #6 (3.5 mm)DETECTION PATTERNS / COUVERTURE DE DETECTION AB(2.3 - 2.4 m)35' / 11m Wide Angle Animal Immune Lens (P/N 5-532-719-00)Top View / Vue de Dessus Side View / Vue de Cote 1207'2m20'6m27'8m35'11m07'2m20'6m13'4m13'4m7'2m20'6m13'4m123451098761112131415161718192007'2m 20'6m 27'8m 35'11m13'4m7'6"(2.3m)01Panasonic CR123A / Duracell DL123 & DL123A /Honeywell 466Observe correct polarity / Observe correct polarity See page 2 for more information / See page 2 for more information Satisfactory No / Non / No- Use only left OR right side corner mounting holes. SMB-10 1 (P/N 0-000-110-01) Swivel Mount Bracket SMB-10C (P/N 0-000-111-01) Swivel Mount Ceiling Bracket SMB-10T 1 (P/N 0-000-155-01) Swivel Mount Bracket w/Tamper IS2500-HSLK 1 35’ x 40’ (11 m x 12 m) High Security Lens Kit IS2500-PALK 2 35’ x 40’ (11 m x 12 m) Pet Alley Lens Kit 1 Not verified by ETL. Mounting Height: 1 7 – 9 ft (2.1 m – 2.7 m). 2 4 ft (1.2 m). FCC & IC AGENCY STATEMENTS ON BOTTOM OF PAGE 2
5800PIRRES-AP Wireless Motion Sensor - Installation Instructions PRELIMINARY DRAFT 8/24/09 - 2 - ENROLL THE SENSOR Enroll the sensor in the control panel prior to its usage in the system. Refer to the control panel instructions for programming details. Program the sensor as an “RF” type (supervised RF) device. To enroll: connect the battery and wait for power up to end (see LED Indications table). When prompted for the serial number, activate the sensor (wave a hand in front of the lens) to enroll the sensor. Loop 1 Pulse count 2; Up to 80 lbs. Animal Immunity LED INDICATIONS Power Up Blinks once per second (for < 45 seconds)Indicator LEDWalk Test ON for 3 seconds = Loop 1 / Low Sensitivity Alarm Flickers rapidly for 3 seconds = walk test period endedCondition MOUNT THE SENSOR (See page 1) Before mounting the transmitter permanently, conduct Go/No Go tests (see control panel manual) to verify adequate signal strength and reorient or relocate the sensor if necessary. For Animal (Pet) Immunity: • Install the sensor where animals cannot come within 6 ft (1.8 m) of the sensor by climbing on furniture or other objects. • Aim the sensor away from stairways, furniture or other objects that can be climbed on by animals. • Do not use optional swivel mount brackets. WALK TESTING The 10 minute walk test mode begins after power up, and can be restarted by removing and replacing the battery. As you walk through the detection pattern, the sensor LED will light for 3 seconds to indicate each alarm detection. Note: In walk test mode all transmissions will be sent as they occur. During normal operation, only one transmission sequence will occur within a 3-minute period to conserve battery life. TROUBLESHOOTING Problem: The system displays a “low battery” message. Solution: Replace the battery within 7 days. SPECIFICATIONS Power: Battery* (included). 1 x 3 V, Lithium; CR123A / DL123 / DL 123A / 466 Battery Life, years (typical): 5 RF Frequency: 315 MHz Operating Temperature: (for indoor use environment) 14° to 131° F (-10° to 55° C) Relative Humidity, no condensation: 95% max. Detectable Walk Rate: 0.7 – 7ft/Sec. (0.2 – 2.0m/Sec.) Temperature Compensation: Advanced Dual Slope APPROVALS / LISTINGS • FCC • IC • C-Tick • CE • SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity. • cETLus Listed COMPLIANCE NOTES • Product must be tested at least once each year. • Product must be installed within the protected area only. FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules and RSS-210 of the IC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.  2009 Honeywell International Inc. Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. Assembled in Mexico. For the latest U.S. warranty information, please go to: www.honeywell.com/security/hsc/resources/wa or Please contact your local authorized Honeywell representative for product warranty information. Ê800-13192-ŠP/N 800-13192 Rev A 10/12 * Battery Caution: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C), or incinerate. Dispose of used batteries promptly. Keep away from children. 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 www.honeywell.com/security

Navigation menu