Acoustic Arc AAI-DS0620A-0 Wireless Speaker System User Manual

Acoustic Arc International Ltd. Wireless Speaker System

User Manual

DS0620A2.4GHz Wireless OutdoorSpeaker SystemOwner's Manual(Read carefully the instructions before using this system)
IntroductionThis 2.4GHz digital wireless speaker system utilizes the most advanced wireless technology todeliver dynamic, high-quality audio anywhere inside or outside your home. The wireless audiotransmission travels freely through walls, floors and other solid objects. Simply connect thesystem to any audio source such as Radio, TV, VCR, Hi-Fi and CD/MP3/ VCD/DVD players... toenjoy full-spectrum, lifelike sound without complicated wiring and installation.Features1. 2.4GHz Frequency Hopping Spread Spectrum (FHSS) digital transmission.2. 32-Channel scan-tuning between transmitter and receiver.3. Audio output power up to 20 Watts RMS per channel.4. Weather-resistant speaker and remote control.5. Mood light effect.6. Dual weather-resistant speaker driver (super bass and tweeter built-in).7. Pairing between transmitter and speaker8. Supports stereo audio (with optional additional speaker).9. AUX In jack.10. Operating distance up to 50 meters in open area (less through walls and other obstructions).11. Works through walls, floors and anywhere in the room.12. Virtually interference-free stereo quality.13. Electronic Volume Control on Speakers14. Remote control unit.15. Powered by 6 D batteries, or by included AC/DC adapter.Package contenti. 1 x RF transmitterii. 1 x RF speakeriii. 1 x Remote controliv. 1 x ac/dc adapter for transmitterv. 1 x ac/dc adapter for speakervi. 1 x RCA to RCA cablevii. 1 x 3.5mm to 6.3 mm adapter plugviii. 1 x user manual
TransmitterSpeaker
Remote ControlInstallationTransmitter1. Plug the included AC/DC adapter into a standard wall outlet.2. Insert the adapter connector plug firmly into the DC IN jack located on the rear panel of thetransmitter base.3. Extend the retractable audio cable located on the back panel of the transmitter and connect itto the output jack of virtually any audio source.Note : Do not fully extend the cable until ready to retract.4. To retract the cable, pull it until it is fully extended and then allow it to feed back into thebase.Speaker ReceiverBattery Power1. To operate the speaker using battery power, gently turn the speaker over and open thebattery compartment cover located underneath.2. Insert six (6) D alkaline batteries (not provided) into the battery compartment, observingproper +/- polarities as indicated.3. Replace the battery compartment cover.
AC Power1. To operate the speaker using AC power, plug the included 12V power adapter into astandard wall outlet.2. Insert the power adapter connector firmly into the DC IN jack located on the back panel ofthe speaker.Operation1. To switch on the speaker, press the POWER button 3sec. located on the front panel of thespeaker. The GREEN power LED illuminates.2. To switch off the speaker, press the POWER button 3sec again.Remote Control The remote control is ready to use with a factory-installed button cell battery. It can be storedin the recessed area on the front panel.Basic Operation1. When the transmitter power adapter is connected and plugged into a standard wall outlet, thetransmitter's GREEN led remains on.2. To switch on the speaker, press the POWER button 3sec on the front panel of the speaker.
The GREEN led illuminates.3. Turn on the audio source the transmitter is turned off for less then 4 minutes, the blue LEDson the transmitter and the speaker illuminate when the audio signal link between the two ismade.4. If the audio source connected to the transmitter is turned off for less than 4 minutes, theBLUE leds on the transmitter and the speaker remain on, but no sound is transmitted.When the audio signal returns to the transmitter, sound is transmitted again.5. If no signal is detected for more than 4 minutes, the transmitter automatically turns off ; theBLUE leds on the transmitter and the speaker switch to GREEN.6. If no signal is detected from the transmitter for more than 5 minutes, the speakerautomatically shifts to Standby mode.7. To turn on the speaker again during Standby mode, press the POWER button on remotecontrol unit. (not need, please delete)8. If no audio signal is detected from the transmitter for more than 15 minutes, the speakerautomatically turns off. The GREEN led goes off.9. To switch on the speaker, press the POWER button 3sec on the front panel of the speaker.10. To switch off the speaker. Press the POWER button 3sec again.PAIRING1. If there is no audio sound is detected after connecting is done, re-pairing processes isrequired. 2. Press the “PAIR” buttons on both transmitter and speakers Mood light /Pair button for 5seconds, there will have a “Du” sound detected when the pairing process is finished.Mood LightFor mood light effect, press the LIGHTS button on the speaker or remote control.Left / Right Channel and Mono SelectionThe Wireless Outdoor Speaker System comes with one speaker and is designed for either Mono orStereo playback. For stereo playback, an additional speaker must be purchased separately. Monoplayback is suggested when only one speaker is used in an area or room.Mono PlaybackTo enable Mono playback, ensure that the switch located on the back panel of the speaker is in theMONO position.Stereo PlaybackTo enable Stereo playback, set the switch on one of the two speakers' back panel to LEFT. Set theswitch on the other speaker to RIGHT.Note 1 : It is also possible to listen to only the Left or Right audio channel using only the speaker
set. To do so, simply set the switch on the speaker's back panel to LEFT or RIGHT. Only thechannel selected will be audible.Note 2 : If two speakers are connected to the system, ensure both speakers are placed within theeffective operational range. If either speaker is out of range it will cause distortion to bothspeakers.AUX InTo connect an audio device directly to the speaker, insert the output audio cable from the device intothe AUX In jack located on the back panel of the speaker.Note :If the source signal is too weak for reception, the transmitter automatically switched off afterapproximately 4 minutes to protect the unit and save power. If the source signal returns to anadequate level, the transmitter automatically switches back on.When the transmitter is in Standby mode, the speaker automatically switches off afterapproximately 20 minutes to protect the unit and save power.To switch speaker power back on during Standby mode, press the POWER button on the remotecontrol. The signal link between the transmitter and speaker reconnects automatically.TroubleshootingNo soundEnsure the AC adapter is securely plugged into the wall outlet and the transmitter DC IN jack.Ensure the speaker POWER button is in the ON position.Speaker batteries may be too weak. Replace with new batteries or connect with the includedac/dc adapter.Ensure the connected audio device is switched on and producing a signal.Ensure that the volume level is set to a moderate level.Redo the pairing process by pressing the “Pair” button on the speakers and transmittersimultaneously.DistortionSpeaker batteries may be too weak, Replace with new batteries or connect with the includedac/dc adapter.Ensure that the volume level is set to a moderate level.The speakers are too fat from the transmitter. Move closer to the transmitter base.The audio input signal may be too low : increase the volume level of the audio source.If two speakers are connected to the system, ensure both speakers are placed within the effectiveoperational range. If either speaker is out of range it will cause distortion to both speakers.
SpecificationsTransmission Mode : UHF StereoCarrier Frequency : 2.4GHz DigitalOperation Voltage : Transmitter, DC 6C 300mASpeaker, DC 12V 1.5A or 6 x D alkaline batteries (not included)Remote Control, 1 x CR2032 button cellFrequency Response : 30 Hz – 20 KHzDistortion : 0.5%S/N Ratio : 65 dBOperation Distance : Up to 50 meters (open area)Speaker Audio Output Power : 20W Max. (RMS)FCC statementsThis device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications to this unit not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, may causeharmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference by one or moreof the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.Consult the dealer or an experienced radio/TV technician for help.If you have any questions ,Please feel free to our website : www.acousticarc.comOur model no.: DS0620A , 2.4GHz wireless speaker system.

Navigation menu