Acoustic Arc AAI-AS0720-00 900 MHz Floating wireless speaker User Manual

Acoustic Arc International Ltd. 900 MHz Floating wireless speaker

User Manual

AS0720 Floating Wireless Speaker System
PINTRODUCTIONThis Outdoor Wireless Speaker System uses the latest 900Mhz wireless technology to enable you to enjoymusic outdoors in your swimming pool. It is simple to connect the portable transmitter to typical audio sourcessuch as an i-Pod, Hi-Fi, CD/MP3 player or other audio source.A. INSIDE THE PACKAGE1. Transmitter base2. Outdoor speaker3. AC adapter for transmitter4. AC adapter for speaker5. Input adapter (3.5mm audio plug to RCA type audio cable)6. User ManualB. FEATURES1. 900 MHz wireless technology2. Auto Scan System to lock speakers onto the strongest signal3. Phase Lock Loop (PLL) transmitter4. Water-proof Speaker5. Open air operating distance of up to 150 feet.6. ON/OFF control on Transmitter7. Auto Shut-Off on Speaker8. Retrackable 3.5mm audio plug on transmitter9. Switchable mood light directed downward into the water10. Battery operation for complete portability of transmitter and speaker
PC. COMPONENTS IDENTIFICATION1. TRANSMITTER2. SPEAKER
PD. INSTALLATION1. TRANSMITTERA. Connect the supplied AC power adapter to an electrical wall outlet.B. Plug the AC power adapter in the DC jack located on the rear of the transmitter.C. Or you can insert 4 X “AAA” size ALKALINE batteries (not supplied) into the battery compartment at thebottom of the transmitter with correct polarity.D. The rear of the transmitter has one audio cord that can be connected to audio output jack of TV, i-pod,DVD, and CD/MP3 players or to headphone/earphone jack with the connector provided.Turn the switch to On and the LED of transmitter will light up in Green. When the audio cable has beenconnected turn on the audio source to at least the mid range level and play the music. The LED will turn fromGreen to Blue (note: if the audio source is not in the play mode the LED will not turn from green to blue). If aspeaker is not turned on within 4 minutes the transmitter light will turn from Blue back to green to save power.2. SPEAKERA. Insert 6 x AA size ALKALINE batteries (not supplied) into the battery compartment with correct polarity atthe bottom of the speaker.B. Tighten the battery door clockwise and make sure it is closed firmly without any gap.C. Press the Power button to turn the speaker ON. The Power LED will light up in Green. When the signallink is established between the transmitter and speaker, the LED on the speaker will change to Blue.Battery Compartment
PE. OPERATION1. Turn on the transmitter. The LED will light up in Green.2. Turn on the audio source (TV or audio component like an iPod) to which the transmitter is connected. TheLED will change from Green to Blue.3. Select channel 1, 2 or 3 of the transmitter for best performance in your location.4. Turn on the Power button on the speaker. Press the Autoscan button. Adjust the volume by pressing “+”and “-“ for desired listening level.Caution: Screw the battery door clockwise to tightly close it and to make sure there is no gap before placing thespeaker into the water.5. Both transmitter and speaker can be powered by power adapters..SWITCHING OFF1. If there is no audio input signal to the transmitter for a 4 minute period, the transmitter will go into standbymode and the LED will change from Blue to Green.2. If the audio source is off, the LED on the transmitter will change to Green.3. The Speaker will turn to standby mode if there is no input signal to transmitter and the LED becomesGreen. The Speaker will automatically shut off when standby mode continues for 5 minutes.4. While in standby mode, the speaker will turn to On automatically after getting a signal from transmitter.OTHER CONTROL1. Select volume up and down on Speaker.2. Select Light button to turn on the mood light effect in the water. This feature works only when the Speaker is
Pturned on.3. If you hear interference that may be coming from other devices, you can adjust the tuning control by movingthe channel knob to 1, 2 or 3 on the transmitter. Then press the “Scan” button on the speaker for bestreception.F. TROUBLE SHOOTINGNO SOUND-Too much water retention inside the speaker grill. Turn the speaker over and gently shake it to let thewater drain out.-Ensure you have fresh alkaline batteries for both transmitter and receiver if the speaker’s and/ortransmitter’s battery charge is too low, sound distortion will be heard. Replace with new batteries.-Ensure the audio component is ON and its volume is set to at least 50%.-The connected audio equipment is not playing. Start playing the equipment.-The volume of speaker is too low, adjust the volume to an appropriate level. Adjust your audio sourcecomponent volume to maximum.DISTORTED-Too much water retention inside the speaker grill. Turn the speaker over and gently shake it to letthe water drain out.-Press the “Scan” button on the speaker to best match the frequency of the transmitter.-Change the position of the channel selector on the transmitter. You must then press the “Scan”button on the speakers.-Battery capacity is too low. Replace with the new batteries.-Ensure the volume level of speakers is adjusted properly.-The speaker is too far from transmitter, move closer.-The input level of the audio signal is too low. Turn up the volume of the audio source equipment.
PG. TECHNICAL SPECIFICATIONSTransmission Mode : UHF stereoCarrier Frequency : 900 MHzOperation Voltage : Transmitter, 4 X “AAA” size Alkaline batteries(not included) or DC 6V 300mA adaptorSpeaker, 6 X“AA”size Alkaline batteries (notincluded) or DC 9V 1.2A adapterFrequency Response : 40Hz – 12KHzDistortion : 1.5%S/N Ratio : 65dB (typical)Operation Distance : Up to 150feetOutput Power : 2.5W + 2.5W (Max)WARNING : Changes or modifications to this unit not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment. Operation is subject tothe following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of thedevice.This device complies with RSS-210 of Industry and Science Canada. Operation is subject tothe following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference that may cause undesired operation of the device.FCC statementsThis device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.Warning: Changes or modifications to this unit not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:¨Reorient or relocate the receiving antenna.¨Increase the separation between the equipment and receiver.¨Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.¨Consult the dealer or an experienced radio/TV technician for help.
P

Navigation menu