Accton Technology 3CRWE554G72 OfficeConnect Wireless 11g Cable/DSL Gateway User Manual Part 1 Revised

Accton Technology Corp OfficeConnect Wireless 11g Cable/DSL Gateway Users Manual Part 1 Revised

Contents

Users Manual Part 1 Revised

http://www.3com.com/Part No. DUA0055-4AAA01Rev. 01Published July 2003OfficeConnect® Wireless 11g Cable/DSL GatewayUser Guide3CRWE554G72
3Com Corporation5500 Bayfront Plaza Santa Clara, California 95052-8145Copyright © 2003, 3Com Corporation. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from 3Com Corporation.3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of 3Com Corporation to provide notification of such revision or change.3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied or expressed, including, but not limited to, the implied warranties, terms or conditions of merchantability, satisfactory quality, and fitness for a particular purpose. 3Com may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time.If there is any software on removable media described in this documentation, it is furnished under a license agreement included with the product as a separate document, in the hard copy documentation, or on the removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy, please contact 3Com and a copy will be provided to you.UNITED STATES GOVERNMENT LEGENDIf you are a United States government agency, then this documentation and the software described herein are provided to you subject to the following: All technical data and computer software are commercial in nature and developed solely at private expense. Software is delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item” as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in 3Com’s standard commercial license for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface any portion of any legend provided on any licensed program or documentation contained in, or delivered to you in conjunction with, this User Guide.Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered in other countries.3Com, OfficeConnect and the 3Com logo are registered trademarks of 3Com Corporation. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Novell and NetWare are registered trademarks of Novell, Inc. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company, Ltd.Netscape Navigator is a registered trademark of Netscape Communications.JavaScript is a trademark of Sun MicrosystemsWi-Fi and the Wi-Fi logo are registered trademarks of the WI-Fi Alliance.IEEE and 802 are trademarks of the Institute of Electrical and Electronics Engineers, Inc.All other company and product names may be trademarks of the respective companies with which they are associated.ENVIRONMENTAL STATEMENTIt is the policy of 3Com Corporation to be environmentally-friendly in all operations. To uphold our policy, we are committed to:Establishing environmental performance standards that comply with national legislation and regulations.Conserving energy, materials and natural resources in all operations.Reducing the waste generated by all operations. Ensuring that all waste conforms to recognized environmental standards. Maximizing the recyclable and reusable content of all products.Ensuring that all products can be recycled, reused and disposed of safely.Ensuring that all products are labelled according to recognized environmental standards.Improving our environmental record on a continual basis.End of Life Statement3Com processes allow for the recovery, reclamation and safe disposal of all end-of-life electronic components.Regulated Materials Statement3Com products do not contain any hazardous or ozone-depleting material.Environmental Statement about the DocumentationThe documentation for this product is printed on paper that comes from sustainable, managed forests; it is fully biodegradable and recyclable, and is completely chlorine-free. The varnish is environmentally-friendly, and the inks are vegetable-based with a low heavy-metal content.
CONTENTSABOUT THIS GUIDENaming Convention 7Conventions 8Feedback about this User Guide 8Related Documentation 9Product Registration 91INTRODUCING THE GATEWAYOfficeConnect Wireless 11g Cable/DSL Gateway 11Gateway Advantages 13Package Contents 13Minimum System and Component Requirements 14Front Panel 14Rear Panel 162HARDWARE INSTALLATIONIntroduction 19Safety Information 19Positioning the Gateway 19Using the Rubber Feet 20Wall Mounting 20Before you Install your Gateway 21Powering Up the Gateway 22Connecting the Gateway 223SETTING UP YOUR COMPUTERSObtaining an IP Address Automatically 25Windows 2000 25Windows XP 27Windows 95/98/ME 27
Macintosh 27Disabling PPPoE and PPTP Client Software 28Disabling Web Proxy 284RUNNING THE SETUP WIZARDAccessing the Wizard 29Password 32Time Zone 32WAN Settings 33LAN Settings 38DHCP 38Wireless Settings 39Summary 405GATEWAY CONFIGURATIONNavigating Through the Gateway Configuration Pages 41Main Menu 41Option Tabs 42Welcome Screen 42Notice Board 42Password 43Wizard 44LAN Settings 44Unit Configuration 44DHCP Clients List 45Wireless Settings 47Configuration 47Encryption 49Configuring WPA Encryption 49Configuring WEP Encryption 50Connection Control 53Client List 55Profile 55Internet Settings 57Connection to ISP 58Firewall 63Virtual Servers 63
Special Applications 65PC Privileges 67URL Filter 69Security 73System Tools 75Restart 75Time Zone 76Configuration 77Upgrade 78Status and Logs 78Status 79Usage 79Logs 80Support/Feedback 80Support 81Feedback 816TROUBLESHOOTINGBasic Connection Checks 83Browsing to the Gateway Configuration Screens 83Connecting to the Internet 84Forgotten Password and Reset to Factory Defaults 85Wireless Networking 85Replacement Power Adapters 87Alert LED 88Recovering from Corrupted Software 89Frequently Asked Questions 90AUSING DISCOVERYRunning the Discovery Application 93Windows Installation (95/98/2000/Me/NT) 93BIP ADDRESSINGThe Internet Protocol Suite 95Managing the Gateway over the Network 95IP Addresses and Subnet Masks 95
How does a Device Obtain an IP Address and Subnet Mask? 97DHCP Addressing 97Static Addressing 97Auto-IP Addressing 97CTECHNICAL SPECIFICATIONSStandards 100DSAFETY INFORMATIONEEND USER SOFTWARE LICENSE AGREEMENTFISP INFORMATIONGLOSSARYINDEXREGULATORY NOTICES FOR THE WIRELESS 11G CABLE/DSL GATEWAY
ABOUT THIS GUIDEThis guide describes how to install and configure the OfficeConnect Wireless 11g Cable/DSL Gateway (3CRWE554G72).This guide is intended for use by those responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks) and Internet gateway systems.If a release note is shipped with the OfficeConnect Wireless 11g Cable/DSL Gateway and contains information that differs from the information in this guide, follow the information in the release note.Most user guides and release notes are available in Adobe Acrobat Reader Portable Document Format (PDF) on the 3Com World Wide Web site:http://www.3com.comNaming Convention Throughout this guide, the OfficeConnect Wireless 11g Cable/DSL Gateway is referred to as the “Gateway”.Category 3 and Category 5 Twisted Pair Cables are referred to as Twisted Pair Cables throughout this guide.
8ABOUT THIS GUIDEConventions Table 1 and Table 2 list conventions that are used throughout this guide.Feedback about thisUser GuideYour suggestions are very important to us. They will help make our documentation more useful to you. Please e-mail comments about this document to 3Com at:pddtechpubs_comments@3com.comPlease include the following information when commenting:■Document title■Document part number (on the title page)■Page number (if appropriate)Table 1 Notice IconsIcon Notice Type DescriptionInformation note Information that describes important features or instructions.Caution Information that alerts you to potential loss of data or potential damage to an application, system, or device.Warning Information that alerts you to potential personal injury.Table 2 Text ConventionsConvention DescriptionThe words “enter” and “type” When you see the word “enter” in this guide, you must type something, and then press Return or Enter. Do not press Return or Enter when an instruction simply says “type.”Keyboard key names If you must press two or more keys simultaneously, the key names are linked with a plus sign (+). Example:Press Ctrl+Alt+Del Words in italics Italics are used to:■Emphasize a point.■Denote a new term at the place where it is defined in the text.■Identify menu names, menu commands, and software button names. Examples:From the Help menu, select Contents.Click OK.
Conventions 9Example:■OfficeConnect Wireless 11g Cable/DSL Gateway User Guide■Part Number DUA0055-4AAA01■Page 24Do not use this e-mail address for technical support questions. For information about contacting Technical Support, please refer to the Support and Safety Information sheet.RelatedDocumentationIn addition to this guide, each Gateway document set includes one Installation Guide. This guide contains the instructions you need to install and configure your Gateway.Product Registration You can now register your Gateway on the 3Com web site and receive up-to-date information on your product:http://www.3com.com/register/
10 ABOUT THIS GUIDE
1INTRODUCING THE GATEWAYWelcome to the world of networking with 3Com®. In the modern business environment, communication and sharing information is crucial. Computer networks have proved to be one of the fastest modes of communication but, until recently, only large businesses could afford the networking advantage. The OfficeConnect® product range from 3Com has changed all this, bringing networks to the small office.The products that compose the OfficeConnect range give you, the small office user, the same power, flexibility, and protection that has been available only to large corporations. Now, you can network the computers in your office, connect them all to a single Internet outlet, and harness the combined power of all of your computers.OfficeConnect Wireless 11g Cable/DSL GatewayThe OfficeConnect Wireless 11g Cable/DSL Gateway is designed to provide a cost-effective means of sharing a single broadband Internet connection amongst several wired and wireless computers. The Gateway also provides protection in the form of an electronic “firewall” preventing anyone outside of your network from seeing your files or damaging your computers. The Gateway can also prevent your users from accessing Web sites which you find unsuitable.Figure 1 shows an example network without a Gateway. In this network, only one computer is connected to the Internet. This computer must always be powered on for the other computers on the network to access the Internet.
12 CHAPTER 1: INTRODUCING THE GATEWAYFigure 1 Example Network Without a GatewayWhen you use the Gateway in your network (Figure 2), it becomes your connection to the Internet. Connections can be made directly to the Gateway, or to an OfficeConnect Switch or Hub, expanding the number of computers you can have in your network.Figure 2 Example Network Using a Wireless Cable/DSL Gateway
Gateway Advantages 13Gateway Advantages The advantages of the Gateway include:■Shared Internet connection for both wired and wireless computers■High speed 802.11g wireless networking■No need for a dedicated, “always on” computer serving as your Internet connection■Cross-platform operation for compatibility with Windows, Unix and Macintosh computers■Easy-to-use, Web-based setup and configuration■Provides centralization of all network address settings (DHCP)■Acts as a Virtual server to enable remote access to Web, FTP, and other services on your network■Security — Firewall protection against Internet hacker attacks and encryption to protect wireless network traffic■Filtered access of inappropriate Web sites using the built-in URL filterPackage Contents The Gateway kit includes the following items:■One OfficeConnect Wireless 11g Cable/DSL Gateway■One power adapter for use with the Gateway■Four rubber feet■One Ethernet cable■One CD-ROM containing the Gateway Discovery program and this User Guide■Installation Guide■One Support and Safety Information Sheet■One Warranty FlyerIf any of these items are missing or damaged, please contact your retailer.
14 CHAPTER 1: INTRODUCING THE GATEWAYMinimum System and Component RequirementsYour Gateway requires that the computer(s) and components in your network be configured with at least the following:■A computer with an operating system that supports TCP/IP networking protocols (for example Windows 95/98/NT/Me/2000/XP, Unix, Mac OS 8.5 or higher).■An Ethernet 10Mbps or 10/100 Mbps NIC for each computer to be connected to the four-port switch on your Gateway.■An 802.11b or 802.11g wireless NIC.■A cable modem or DSL modem with an Ethernet port (RJ-45 connector).■An active Internet access account.■A Web browser that supports JavaScript, such as Netscape 4.7 or higher, Internet Explorer 5.0 or higher, or Mozilla 1.2.1 or higher.Front Panel The front panel of the Gateway contains a series of indicator lights (LEDs) that help describe the state of various networking and connection operations.Figure 3 Gateway - Front Panel1 Alert LEDOrangeIndicates a number of different conditions, as described below.Off - The Gateway is operating normally.Flashing quickly - Indicates one of the following conditions:■The Gateway has just been started up and is running a self-test routine, or 21 43OfficeConnect Wireless 11g Cable/DSL Gateway3CRWE554G72LAN Status Cable/DSL5WLANAlert Enabled
Front Panel 15■The administrator has invoked the Reset to Factory Defaults command, or■The system software is in the process of being upgradedIn each of these cases, wait until the Gateway has completed the current operation and the alert LED is Off.Flashing slowly - The Gateway has completed the Reset to Factory Defaults process, and is waiting for you to reset the unit. To do this, remove power, wait 10 seconds and then re-apply power. The Gateway will then enter the start-up sequence and resume normal operation.If you have used a cable to reset the unit to Factory Defaults, follow steps 5 to 7 in “Forgotten Password and Reset to Factory Defaults” on page 85.On for 2 seconds, and then off - The Gateway has detected and prevented a hacker from attacking your network from the Internet.Continuously on - A fault has been detected with your Gateway during the start-up process. Refer to Chapter 6 “Troubleshooting”.2Power LEDGreenIndicates that the Gateway is powered on.3 Wireless LAN (WLAN) Status LED YellowIf the LED is on it indicates that wireless networking is enabled. If the LED is flashing, data is being transmitted or received. If the LED is off, the Wireless LAN has been disabled in the Gateway, or there is a problem. Refer to Chapter 6 “Troubleshooting”.4 Four LAN Status LEDsGreen (100Mbps link) / yellow (10Mbps link)If the LED is on, the link between the port and the next piece of network equipment is OK. If the LED is flashing, the link is OK and data is being transmitted or received. If the LED is off, nothing is connected, the connected device is switched off, or there is a problem with the connection (refer to Chapter 6 “Troubleshooting”). The port will automatically adjust to the correct speed and duplex.
16 CHAPTER 1: INTRODUCING THE GATEWAY5 Cable/DSL Status LEDGreen (100Mbps link) / yellow (10Mbps link)If the LED is on, the link between the Gateway and the cable or DSL modem is OK. If the LED is flashing, the link is OK and data is being transmitted or received. If the LED is off, nothing is connected, the modem is switched off or there is a problem (refer to Chapter 6 “Troubleshooting”).Rear Panel The rear panel (Figure 4) of the Gateway contains four LAN ports, one Ethernet Cable/DSL port, a power adapter OK LED, and a power adapter socket.Figure 4 Gateway - Rear Panel6 Wireless AntennaeThe antennae on the product should be placed in a ‘V’ position when initially installed.CAUTION: Do not force the antennae beyond their mechanical stops. Rotating the antennae further may cause damage.7 Power Adapter SocketOnly use the power adapter supplied with this Gateway. Do not use any other adapter.8 Power Adapter OK LEDGreenIndicates that the power adapter is supplying power to the Gateway. If the LED is off, there may be a problem with the power adapter or adapter cable.9 Ethernet Cable/DSL portUse the supplied patch cable to connect the Gateway to the Ethernet port on your cable or DSL modem. The port will automatically adjust to the correct speed and duplex, and will set itself to MDI or MDIX 7 9 1084EthernetCable/DSLOK6 6LAN
Rear Panel 17depending on the device to which they are connected and the type of cable used.10 Four 10/100 LAN portsUsing suitable RJ-45 cable, you can connect your Gateway to a computer, or to any other piece of equipment that has an Ethernet connection (for example, a hub or a switch). The LAN ports will automatically set themselves to MDI or MDIX depending on the device to which they are connected and the type of cable used.
18 CHAPTER 1: INTRODUCING THE GATEWAY
2HARDWARE INSTALLATIONIntroduction This chapter will guide you through a basic installation of the Gateway, including:■Connecting the Gateway to the Internet.■Connecting the Gateway to your network.■Setting up your computers for networking with the Gateway.Safety InformationWARNING: Please read the “Safety Information” section in Appendix D before you start.VORSICHT: Bitte lesen Sie den Abschnitt “Wichtige Sicherheitshinweise” sorgfältig durch, bevor Sie das Gerät einschalten.AVERTISSEMENT: Veuillez lire attentivement la section “Consignes importantes de sécurité” avant de mettre en route.Positioning the Gateway You should place the Gateway in a location that:■is conveniently located for connection to the cable or DSL modem that will be used to connect to the Internet.■is centrally located to the wireless computers that will connect to the Gateway. A suitable location might be on top of a high shelf or similar furniture to optimize wireless connections to computers in both horizontal and vertical directions, allowing wider coverage.■allows convenient connection to the computers that will be connected to the four LAN ports on the rear panel, if desired.■allows easy viewing of the front panel LED indicator lights, and access to the rear panel connectors, if necessary.
20 CHAPTER 2: HARDWARE INSTALLATIONWhen positioning your Gateway, ensure:■It is out of direct sunlight and away from sources of heat.■Cabling is away from power lines, fluorescent lighting fixtures, and sources of electrical noise such as radios, transmitters and broadband amplifiers.■Water or moisture cannot enter the case of the unit.■Air flow around the unit and through the vents in the side of the case is not restricted. 3Com recommends you provide a minimum of 25 mm (1 in.) clearance.Using the RubberFeetUse the four self-adhesive rubber feet to prevent your Gateway from moving around on your desk or when stacking with other flat top OfficeConnect units. Only stick the feet to the marked areas at each corner of the underside of your Gateway.Wall Mounting There are two slots on the underside of the Gateway that can be used for wall mounting. When wall mounting the unit, ensure that it is within reach of the power outlet.You will need two suitable screws to wall mount the unit. To do this:1Ensure that the wall you use is smooth, flat, dry and sturdy and make two screw holes which are 150 mm (5.9 in.) apart.2Fix the screws into the wall, leaving their heads 3 mm (0.12 in.) clear of the wall surface.3Remove any connections to the unit and locate it over the screw heads. When in line, gently push the unit on to the wall and move it downwards to secure. When making connections, be careful not to push the unit up and off the wall.CAUTION: Only wall mount single units, do not wall mount stacked units.
Before you Install your Gateway 21Before you Install your Gateway Before you install and configure your Gateway, you need the following additional information. If you do not have this information, contact your Internet Service Provider (ISP). Space is provided below for you to record this information.If you have a DSL connection and your ISP allocates IP information dynamically over PPPoE, you need a User Name and Password:If you have a DSL connection and your ISP allocates IP information dynamically over PPTP, you need a User Name, Password and PPTP Server Address:You only need a PPPoE Service Name if your ISP requires one. Do not enter anything if your ISP does not require this information.If your ISP allocates fixed or static IP information, you need the following information:PPPoE User Name : ______________________PPPoE Password : ______________________PPPoE Service Name : ______________________PPTP User Name : ______________________PPTP Password : ______________________PPTP Server Address : ____.____.____.____IP Address : ____.____.____.____Subnet Mask : ____.____.____.____Default Gateway address : ____.____.____.____DNS address : ____.____.____.____
22 CHAPTER 2: HARDWARE INSTALLATIONIf your ISP allocates IP information dynamically over a protocol other than PPPoE, you do not need any further information. This configuration is typical of cable connections.Powering Up the Gateway To power up the Gateway:1Plug the power adapter into the power adapter socket located on the back panel of the Gateway.2Plug the power adapter into a standard electrical wall socket.Connecting the Gateway The first step for installing your Gateway is to physically connect it to a cable or DSL modem and then connect it to a computer in order to be able to access the Internet. See Figure 5:Figure 5 Connecting the GatewayTo use your Gateway to connect to the Internet through an external cable or DSL modem:1Insert one end of the supplied Ethernet (RJ-45 Category 5) cable into the Cable/DSL port on the rear panel of the Gateway.2Insert the other end of the cable into the RJ-45 port on your cable or DSL modem. Check that the Cable/DSL status LED lights on the Gateway.3Connect the cable or DSL modem to the Internet.InternetYour existing Cable/DSL ModemPower Supply UnitYour PCWireless Users3Com OfficeConnect Wireless 11g Cable/DSL Gateway
Connecting the Gateway 234Connect your computer to one of the four LAN ports on the Gateway using a twisted pair cable. Check that the corresponding LAN status LED on the Gateway lights.You have now completed the hardware installation of your Gateway. Next you need to set up your computers so that they can make use of the Gateway to communicate with the Internet.3Com recommends that you perform the initial Gateway configuration from a computer that is directly connected to one of the LAN ports. If you configure the Gateway from a wireless computer, note that you may lose contact with the Gateway if you change the wireless configuration.To communicate wirelessly with your Gateway, your wireless NIC should be set as follows:■Encryption — none■Service Area Name/SSID — 3Com■Channel — 11
24 CHAPTER 2: HARDWARE INSTALLATION
3SETTING UP YOUR COMPUTERSThe Gateway has the ability to dynamically allocate network addresses to the computers on your network, using DHCP. However, your computers need to be configured correctly for this to take place. To change the configuration of your computers to allow this, follow the instructions in this chapter. If your computers are configured with fixed or static addresses and you do not wish to change this, then you should use the Discovery program on the Gateway CD-ROM to detect and configure your Gateway. Refer to Appendix A for information on using the Discovery program.Obtaining an IP Address AutomaticallyWindows 2000 If you are using a Windows 2000-based computer, use the following procedure to change your TCP/IP settings:1From the Windows Start Menu, select Settings > Control Panel.2Double click on Network and Dial-Up Connections.3Double click on Local Area Connection.4Click on Properties.5A screen similar to Figure 6 should be displayed. Select Internet Protocol TCP/IP and click on Properties.
26 CHAPTER 3: SETTING UP YOUR COMPUTERSFigure 6 Local Area Properties Screen6Ensure that the options Obtain an IP Address automatically, and Obtain DNS server address automatically are both selected as shown in Figure 7. Click OK.Figure 7 Internet Protocol (TCP/IP) Properties Screen7Restart your computer.
Obtaining an IP Address Automatically 27Windows XP1From the Windows Start menu, select Control Panel.2Click on Network and Internet Connections.3Click on the Network Connections icon.4Double click on LAN or High Speed Connection icon. A screen titled Local Area Connection Status will appear.5Select Internet Protocol TCP/IP and click on Properties.6Ensure that the options Obtain an IP Address automatically, and Obtain DNS servers automatically are both selected. Click OK.7Restart your computer.Windows 95/98/ME1From the Windows Start Menu, select Settings > Control Panel.2Double click on Network. Select the TCP/IP item for your network card and click on Properties.3In the TCP/IP dialog, select the IP Address tab, and ensure that Obtain IP address automatically is selected. Click OK.Macintosh If you are using a Macintosh computer, use the following procedure to change your TCP/IP settings:1From the desktop, select Apple Menu, Control Panels, and TCP/IP.2In the TCP/IP control panel, set Connect Via: to “Ethernet”.3In the TCP/IP control panel, set Configure: to “Using DHCP Server.”4Close the TCP/IP dialog box, and save your changes.5Restart your computer.
28 CHAPTER 3: SETTING UP YOUR COMPUTERSDisabling PPPoE and PPTP Client SoftwareIf you have PPPoE or PPTP client software installed on your computer, you will need to disable it. To do this:1From the Windows Start menu, select Settings > Control Panel.2Double click on Internet Options.3Select the Connections Tab. A screen similar to Figure 8 should be displayed.4Select the Never Dial a Connection option.Figure 8 Internet Properties ScreenYou may wish to remove the PPPoE client software from your computer to free resources, as it is not required for use with the Gateway.Disabling Web Proxy Ensure that you do not have a web proxy enabled on your computer.Go to the Control Panel and click on Internet Options. Select the Connections tab and click LAN Settings at the bottom. Make sure that the Use Proxy Server option is unchecked.
4RUNNING THE SETUP WIZARDAccessing the Wizard The Gateway setup program is Web-based, which means that it is accessed through your Web browser (Netscape Navigator 4.7 or higher, Internet Explorer 5.0 or higher, or Mozilla 1.2.1 or higher). To use the Setup Wizard:1Ensure that you have at least one computer connected to the Gateway. Refer to Chapter 2 for details on how to do this.2Launch your Web browser on the computer. 3Enter the following URL in the location or address field of your browser: http://192.168.1.1 (Figure 9). The Login screen displays.Figure 9 Web Browser Location Field (Factory Default)4To log in as an administrator, enter the password (the default setting is admin) in the System Password field and click Log in (Figure 10).
30 CHAPTER 4: RUNNING THE SETUP WIZARDFigure 10 Gateway Login Screen5If the password is correct, the Country Selection screen will appear. Select the country you wish to configure the Gateway for, then click Apply. (Figure 11)Figure 11 Country Selection Screen6When you have selected a country either:■The Welcome screen will appear (Figure 12). Select the Wizard tab and click Wizard.or
Accessing the Wizard 31■If your Gateway has not been configured before, the Wizard will launch automatically (refer to Figure 13).7Click Next.8You will be guided step by step through a basic setup procedure.Figure 12 Welcome ScreenFigure 13 Wizard Screen
32 CHAPTER 4: RUNNING THE SETUP WIZARDPassword Figure 14 Change Administration Password ScreenWhen the Change Administration Password screen (Figure 14) appears, type the Old Password, then a new password in both the New Password and Confirm Password boxes.3Com recommends entering a new password when setting up the Gateway for the first time. The Gateway is shipped from the factory with a default password, admin.1. Password is case sensitive.2. Write the new password down and keep it in a safe place, so that you can change your settings in the future.Click Next to display the Time Zone setup screen (Figure 15).Time Zone Figure 15 Time Zone ScreenSelect your time zone from the pull-down menu, check the daylight savings option if required, and then click Next.
Accessing the Wizard 33The Daylight Savings option advances the system clock by one hour. It does not cause the system clock to be updated for daylight savings time automatically.WAN Settings Figure 16 Internet Settings ScreenThis Internet Addressing Mode window allows you to set up the Gateway for the type of Internet connection you have. Before setting up your Internet connection mode, have the modem setting information from your ISP ready. Select an Internet Addressing mode from the following:■PPPoE is required (typically DSL users only) see page 34■ISP provides configuration dynamically (via DHCP) see page 35■ISP has provided a static IP address see page 36■PPTP is required (some DSL users in Europe) see page 37and click Next. For further information on selecting a mode see “Internet Settings” on page 57.
34 CHAPTER 4: RUNNING THE SETUP WIZARDPPPoE ModeFigure 17 PPPoE ScreenTo setup the gateway for use with a PPP over Ethernet (PPPoE) connection, use the following procedure:1Enter your PPP over Ethernet user name in the PPPoE User Name text box.2Enter your PPP over Ethernet password in the PPPoE Password text box.3Enter your PPP over Ethernet service name in the PPPoE Service Name text box.This is optional. Not all ISPs require a PPPoE service name.Do not enter anything in this box if your ISP does not require a service name.4Check all of your settings, and then click Next. Refer to “LAN Settings” on page 38 for more information.
Accessing the Wizard 35Dynamic IP Address ModeTo setup the Gateway for use with a dynamic IP address connection:1Select the ISP provides configuration dynamically (via DHCP) and then click Next. See Figure 16.Figure 18 Hostname Screen2Some ISPs require a host name. If your ISP has this requirement, enter the host name in the Host Name text box (Figure 18) and click Next. The Clone MAC Address screen displays.Figure 19 Clone MAC Address Screen3If your ISP requires an assigned MAC address, select Yes, I would like to enter a MAC address manually and enter the values for a MAC address if required (Figure 19). If the computer you are now using is the one that was previously connected directly to the cable modem, choose Yes, please clone the MAC address from the PC I’m currently using.
36 CHAPTER 4: RUNNING THE SETUP WIZARDStatic IP ModeTo setup the Gateway for use with a static IP address connection, use the following procedure:1Select ISP has provided a static IP address, (see Figure 16) and then click Next. Figure 20 displays. Figure 20 Static IP Mode Screen2Enter your IP Address in the IP Address text box.3Enter your subnet mask in the Subnet Mask text box.4Enter your ISP gateway address in the Internet (ISP) Gateway Address text box.5Enter your primary DNS address in the Primary DNS Address text box.6Enter your secondary DNS address in the Secondary DNS Address text box.This step is optional. Not all ISPs require a secondary DNS address.7Check all of your settings, and then click Next.
Accessing the Wizard 37PPTP ModeFigure 21 PPTP Mode ScreenTo setup the gateway for use with a PPTP connection, use the following procedure:1Enter your PPTP server address in the PPTP Server Address text box.2Enter your PPTP user name in the PPTP User Name text box.3Enter your PPTP password in the PPTP Password text box.4Enter your Primary DNS Address and Secondary DNS address.Your ISP may provide you with primary and secondary DNS addresses. If they have been provided, enter the addresses in the appropriate text boxes. If not, leave 0.0.0.0 in the boxes.5Check all of your settings, and then click Next. Figure 22 displays.Figure 22 PPTP IP Settings
38 CHAPTER 4: RUNNING THE SETUP WIZARD6IP settings must be used when establishing a PPTP connection. Fill in the Initial IP Address and the Initial Subnet Mask fields if your ISP has provided you with these settings. Alternatively, if the PPTP server is located in your DSL modem, click Suggest to select an IP address on the same subnet as the PPTP server.LAN Settings Figure 23 LAN IP Address ScreenThis screen displays a suggested LAN IP address and subnet mask of the Gateway. It also allows you to change the IP address and subnet mask.DHCP The Gateway contains a Dynamic Host Configuration (DHCP) server that can automatically configure the TCP/IP settings of every computer on your network.Figure 24 DHCP Server Setup ScreenTo activate the DHCP Server option, select Enable the DHCP server with the following settings: and specify the IP pool range. The largest available continuous IP pool will be automatically entered; if this is not appropriate,
Accessing the Wizard 39make your required changes. To disable DHCP, select Do not enable the DHCP server. Click Next when you have finished.Wireless Settings Figure 25 Wireless Configuration ScreenThis screen displays the Channel and Service Area Name. It also allows you to change these settings. There are a maximum of 14 channels, the number available to you is dependent on the country you reside in. Selecting Clear Channel Select allows the Gateway to automatically select an available channel when first powered on.The Service Area Name default for 3Com products is “3Com”. Up to 32 (case sensitive) characters can be entered for the Service Area Name.3Com strongly recommends that you change the SSID to something other than the default.If you are configuring the Gateway from a wireless computer any changes you make to the wireless configuration will result in communication between the Gateway and your computer being lost. This is why 3Com strongly recommends that you configure the Gateway from a wired computer.It is very important that you set up your wireless clients to use the same Service Area Name or SSID as the one you use on this screen. If your clients use a different Service Area Name then they will not be able to communicate with the Gateway.The choice of channel is less important as Clients will generally search all of the available channels. You should however make a note of the
40 CHAPTER 4: RUNNING THE SETUP WIZARDchannel you select as this may be useful if you experience problems with your clients.Summary Figure 26 Configuration Summary ScreenWhen you complete the Setup Wizard, a configuration summary will display. Verify the configuration information of the Gateway and then click Finish to save your settings. 3Com recommends that you print this page for your records.If you have made changes to the LAN Settings or wireless configuration options, you may need to reconfigure the computer you are using in order to make contact with the Gateway again.Your Gateway is now configured and ready for use.For information on improving your Wireless network security see “Wireless Settings” on page 47.See Chapter 5 for a detailed description of the Gateway configuration screens.
5GATEWAY CONFIGURATIONNavigating Through the Gateway Configuration PagesThis chapter describes all the screens available through the Gateway configuration pages, and is provided as a reference. To get to the configuration pages, browse to the Gateway by entering the URL in the location bar of your browser. The default URL is http://192.168.1.1 but if you changed the Gateway LAN IP address during initial configuration, use the new IP address instead. When you have browsed to the Gateway, log in using your system password (default admin).Main Menu At the left side of all screens is a main menu, as shown in Figure 27 on page 42. When you click on a topic from the main menu, that page will appear in the main part of the screen.■Welcome — displays the firmware version of the Gateway, allows you to change your password, and launch the Wizard■LAN Settings — allows you to configure IP address and subnet mask information, set up DHCP server parameters, and display the DHCP client list.■Wireless Settings — enables /disables access from wireless computers, and provides facilities for improving the security of the wireless network.■Internet Settings — sets up Internet addressing modes such as PPPoE and PPTP connections, allows you to clone the Gateway’s MAC address, and set up dynamic IP address allocation and static IP address settings.■Firewall — allows configuration of the Gateway’s firewall features: Virtual Servers, Special Applications, PCs Privileges, URL Filtering and Security options■System Tools — allows the administrator to perform maintenance activities on the Gateway.
42 CHAPTER 5: GATEWAY CONFIGURATION■Status and Logs — displays the current status and activity logs of the Gateway.■Support/Feedback — contains a comprehensive online help system and allows you to provide 3Com with feedback on your Gateway.Option Tabs Each corresponding menu page may also provide sub-sections which are accessed through the use of tabs (see Figure 27 for example). To access a sub-section, simply click on the required tab.Getting HelpOn every screen, a Help button is available which provides access to the context-sensitive online help system. Click Help for further assistance and guidance relating to the current screen.Welcome Screen The Welcome section allows you to view the Notice board and to change your Password. You can also gain access to the Configuration Wizard. (See “Accessing the Wizard” on page 29 for details).Notice Board Figure 27 Notice Board ScreenThe Notice Board is used to display configuration warning messages. For example, you would be warned if you had disabled wireless networking or wireless encryption.
Welcome Screen 43Password Figure 28 Password ScreenChanging the Administration PasswordYou can change the password to prevent unauthorized access to the Administration System. To do this:1Enter the current password in the Old Password field 2Enter the new password in the New Password field 3Enter the new password again in the Confirm Password field 4Click Apply to save the new password The password is case sensitive.If you have forgotten your password you need to reset the Gateway. See “Forgotten Password and Reset to Factory Defaults” on page 85
44 CHAPTER 5: GATEWAY CONFIGURATIONWizard Figure 29 Wizard ScreenClick WIZARD... to launch the configuration wizard. Refer to Chapter 4 for information on how to run the wizard.LAN Settings The LAN Settings menu provides the following options:Unit Configuration Figure 30 Unit Configuration Screen
LAN Settings 45The LAN Settings screen is used to specify the LAN IP address of your Gateway, and to configure the DHCP server.1Select Unit Configuration and then specify the Gateway IP Address and Subnet Mask in the LAN Settings field. The default IP address of the Gateway is 192.168.1.1.2If you want to use the Gateway as a DHCP Server, click in the Enable check box.3Clicking Auto Range will automatically choose the largest available range of addresses for your network.4Check all of your settings, and then click Apply.The DHCP server will give out addresses to both wired and wireless clients.DHCP Clients List Figure 31 DHCP Clients List ScreenThe DHCP Clients List provides details on the devices that have received IP addresses from the Gateway. The list is only created when the Gateway is set up as a DHCP server. For each device that is connected to the LAN the following information is displayed:■IP address — The Internet Protocol (IP) address issued to the client machine.■Host Name — The client machine’s host name, if configured.■MAC Address — The Media Access Control (MAC) address of the
46 CHAPTER 5: GATEWAY CONFIGURATION■client’s network card.■Client Type — Whether the client is connected to the Gateway by wired or wireless connection.■Fix — This box is checked if the IP address is fixed to the MAC address of the client’s network card. Clients that have fixed addresses will get the same IP address each time they connect.Check the box to fix an association. Uncheck the box to remove the fixed association.As you connect more devices, the client list will grow to a maximum number of 253 clients.The release button allows the lease time for the IP address that has been issued to a device to be cleared. The lease time is set at 12 hours. If a PC has been switched off, using the Release button would allow the 12 hour lease time to be cleared. The IP address would then be available for another device if there were no other IP addresses available.Adding Fixed DHCP MappingsYou can add Fixed Mappings so that the Gateway allocates an IP address chosen by you when it encounters a particular device.You only need to create Fixed Mappings for devices that need a specific IP address. For devices that do not need a specific IP address, the Gateway will automatically allocate addresses.To add a Fixed Mapping:1Click New. The DHCP Fixed Mapping Setup screen will be displayed.2Enter the MAC Address for which you want to create a Fixed Mapping in the MAC Address of Client box.The MAC Address must be entered as 6 hexadecimal pairs, e.g. 12-34-56-78-90-ab.3Enter the IP Address that you want to reserve in the IP Address for client box.4Click Add to add the Fixed Mapping or Close to close the window without adding the Fixed Mapping. The Fixed DHCP Mapping will be displayed in the DHCP Clients list as a Fixed Association.
Wireless Settings 47Wireless SettingsTo improve the security of your wireless network, 3Com recommends that you:1. Change the SSID from its default value - see page 482. Enable Encryption - see page 493. Enable Connection Control - see page 53Configuration Figure 32 Configuration ScreenEnable Wireless NetworkingAllows you to enable/disable the wireless section of your LAN. When disabled, no wireless PCs can gain access to either the Internet or other PCs on your Wired or Wireless LAN through this Gateway.Channel SelectionThe Channel Selector allows you to specify which Channel the Gateway will transmit and receive on. If another access point or gateway nearby is using the same Channel as you, there will be a reduction in the performance of your network. If this seems to be the case, you should select a different channel number. Usually the Wireless computers will scan to find the correct channel, but if they don't you must configure them to use the same Channel number as the Gateway.
48 CHAPTER 5: GATEWAY CONFIGURATIONChoose the Clear Channel Select option to automatically choose the clearest channel. The Gateway will check for the clearest channel whenever it is rebooted, powered up, and when the Clear Channel Select option is first applied.Valid channels are country dependent. See “Channels” on page 121 for a list of channels approved by each country.Service Area Name/SSIDThis allows you to name your Wireless network. The field will accept any alphanumeric string and has a maximum length of 32 characters. Your Wireless computers must be configured with exactly the same name or you will not establish a connection. The Service Area Name may also be referred to as “ESSID” depending on your networking vendor. By default the Gateway uses the name “3Com”. 3Com recommends that you change the default name.In order that your wireless computers can connect to the Gateway, you must:■Use Infrastructure Mode not Adhoc Mode.■Have the same Service Area Name as the Gateway.■Have the same Channel number as the Gateway.■Use the same encryption type and keys as the Gateway.■Ensure that the PC is included in the authorized Wireless PCs list if Connection Control is enabled. See page 53.Enable Broadcast SSIDThis feature can be used to improve the security of your wireless network. When the tickbox is checked, the Gateway will broadcast the Service Area Name/SSID of your wireless network. This will allow unauthorized clients from detecting your SSID and attempting to connect to your network.If you have a wireless client that can detect all the available SSIDs in your area, your client will not list the Gateway SSID unless this feature is enabled. The clients will still be able to connect, provided that they are supplied with the SSID.
Wireless Settings 493Com recommends that you install your wireless network with this feature enabled and then disable it once you have set up the Gateway and wireless clients.Encryption When setting up wireless networks, it is important to remember that with encryption disabled, anyone with a Wireless PC can eavesdrop on your network. 3Com recommends that you get the network working with encryption disabled first and then enable it as the last step. This will simplify setting up your network. The Gateway supports two types of encryption:■WPA — Wi-Fi Protected Access (WPA) is a 256 bit encryption method with keys that change over time.■WEP — Wireless Equivalent Privacy (WEP) is a 64 bit or 128 bit encryption method with user configurable fixed keys.WPA provides a higher level of security, provided by its longer key and dynamic changes made to the key over time. 3Com recommends that you use WPA with any clients which support it.If you enable encryption on the Gateway, you must reconfigure your wireless PCs to use exactly the same Encryption Type and Keys otherwise the devices will not understand each other. The encryption methods used by the Gateway secure data transmitted through wireless communications between the Gateway and its wireless clients. Enabling encryption has no security effect on data transmitted through wired (Ethernet) connections or through your connections to the Internet.Configuring WPAEncryptionThe only configuration that is needed for WPA is to enter the pre-shared key. This key is used to start the dialog between the Gateway and the client. During this dialog, a new key is agreed, making it more difficult to eavesdrop on wireless networks encrypted using WPA, than those encrypted using WEP. The pre-shared key can be entered as a 256 bit series of hexadecimal digits or as a pass-phrase.
50 CHAPTER 5: GATEWAY CONFIGURATIONFigure 33 Encryption Keys Screen showing WPA configurationTo enter the pre-shared key as hexadecimal digits:1Select Enabled - Manual Pre-shared Key from the WPA Encryption Type drop-down box.2Enter a pair of hexadecimal digits in each of the 32 Key fields. Each field can contain a hexadecimal number from 00 to ff, for example 1a.3Click Apply to generate the key.To enter the pre-shared key as a pass-phrase:1Select Enabled - Pre-Shared Passphrase from the WPA Encryption Type drop-down box.2Enter a phrase of between 8 and 63 characters in length in the Passphrase field. This passphrase will be used to generate a 256 bit key.3Click Apply to generate the key.Configuring WEPEncryptionThere are two levels of WEP encryption available, 64 bit (sometimes referred to as 40 bit) and 128 bit. Use the WEP Encryption Type box to select the desired level.
Wireless Settings 51Encryption KeysFigure 34 Encryption Keys Screen showing WEP configurationA Key is a hexadecimal (0-9, A-F) number used to encrypt and decrypt the data. There can be up to 4 keys and each key can be as long as 26 digits. The Gateway also offers a number of methods for converting plain text into hex keys. The text is much easier to remember than hex keys but it relies on your wireless adapters also supporting this feature. Different manufacturers have developed different ways of converting plain text and so interoperability is not guaranteed. If you are experiencing difficulty, the Manual Hex Key method is supported by most vendors. There are four methods available to generate the encryption keys:■Manual Key Entry - This method allows you to manually enter hex keys. Virtually all manufacturers support this scheme. Enter a two digit hexadecimal number in every box. Hexadecimal numbers are formed from 0-9 and A-F. ■3Com Encryption String - This method is supported by 3Com Wireless products. The string can contain any alphanumeric characters and must be between 6 and 30 characters long. A single string will automatically generate 4 unique keys for 64 or 128 bit WEP. ■ASCII - This method is supported by some adapter cards running under Windows XP. The string must be exactly 5 characters for 64 bit
52 CHAPTER 5: GATEWAY CONFIGURATIONWEP and 13 characters for 128 bit WEP. You must enter a separate string for each of the 4 Keys. You can leave a string blank provided this Key is not selected as the Active Transmit Key.■Passphrase - This is another common method and similar to the 3Com Encryption string. In 64 bit WEP, the passphrase will generate 4 different keys. However, in 128 bit WEP, this method only generates 1 key which is replicated for all 4 keys. The passphrase can be up to 31 characters long and may contain any alphanumeric characters.Select the key generation method you wish to use from the drop down list. If you have other wireless products choose the scheme that is compatible with these, then enter the appropriate information.If you encounter any difficulty when you enable WEP ensure that you check that each key on your wireless computer is exactly the same as each key on your Gateway. In other words, Key number 1 on the Wireless computer must have the same Hex number as Key number 1 on the Gateway, Key 2 on the Wireless computer must match Key 2 on the Gateway and so on.The Active Transmit Key selects which of the 4 Keys the Gateway uses when it transmits. You can change the selected key periodically to increase the security of your network.Some wireless adapters have only one key available on their WEP configuration page. If this is the case ensure it is the same as Key 1 on the Gateway and that it is selected as the active transmit key.
Wireless Settings 53Connection Control Figure 35 Connection Control ScreenA higher level of security can be achieved for your wireless network if you use both encryption and you specify only certain wireless computers can connect to the Gateway. By default, any wireless computer that has the same Service Area Name/SSID, channel and encryption settings as the Gateway can connect to it. Select Only Authorized Wireless PCs can connect to the Gateway to enable and configure this feature.If you enable this feature from a Wireless PC, it will automatically be added to the Authorized Wireless PC list.Authorized Wireless PCsFigure 36 Connection Control Detail Screen
54 CHAPTER 5: GATEWAY CONFIGURATIONTo create a list of Wireless computers that can access the Gateway: 1Press New. The screen shown in Figure 36 opens.2Select the MAC addresses of the Wireless PCs for which you want to allow access.To select multiple MAC addresses, hold down the Ctrl key while clicking on the addresses.The drop down list on the Connection Control window will contain the MAC addresses of all Wireless PCs that are in range, currently operating, and have the same Service Area Name/SSID, channel and encryption settings as the Gateway. You will find this screen easier to use if you set up and make a note of all of your wireless PC's on your network first. You may also add the entries manually if you know the MAC address. To add a MAC address that is not in the list, enter the MAC address in the appropriate fields. A MAC address consists of 12 characters. Valid characters are '0-9', and 'A-F'. 3Press Add.Click Close to discard all changes.Modifying a MAC Address1Click on the MAC address to be modified in the table (Figure 37).2Modify the MAC address.3Press Apply to accept the changes.Figure 37 MAC Address TableClick Close to discard all changes.Deleting a MAC AddressThe connection rights for a Wireless PC listed in the table can be removed by pressing Delete for that entry in the table.
Wireless Settings 55Once an entry has been deleted it cannot be undone. Please wait 30 seconds for changes to take effect.Client List Figure 38 Client List ScreenThe Wireless Client List provides details on the devices that are connected to the Wireless LAN. The list is only created when Wireless Networking is enabled. For each device that is connected to the Wireless LAN, the MAC address and Connection Speed of that device is displayed. As you connect more devices to the Wireless LAN, the client list will grow to a maximum of 32 (the maximum number of wireless devices that the Gateway can support).Profile Figure 39 Profile Screen
56 CHAPTER 5: GATEWAY CONFIGURATIONSome 3Com Wireless Network Adapters allow you to import Wireless configurations via a ‘profile’. The Gateway can generate a profile so that you do not need to configure your Wireless PCs manually.The profile contains three items as follows:■Service Area Name/SSID of the GatewayThis is configured on the Configuration tab under the Wireless Settings option.■Encryption settings from the GatewayThis is configured on the Encryption tab under the Wireless Settings option.■Profile NameThis is used to identify the profile once it has been imported into the Wireless Network Adapter configuration software.To set up a profile (once the Service Area Name/SSID and Encryption settings have been configured in the Gateway):1Enter a Profile Name (up to 25 alphanumeric characters) and then click Save Profile. 2Your browser will then prompt you to enter a file name and folder location in which to save the profile. Once the profile has been saved it can be copied on to another PC and imported into the 3Com Wireless Network Adapter. For instructions on how to import a profile, refer to the User Guide that accompanies your 3Com Wireless Network Adapter(s).If, once the profile is imported, the Wireless Network Adapter cannot connect to the Gateway, check that:■the adapter is within range of the Gatewayif Connection Control has been enabled in the Gateway, the MAC address of the Wireless Network Adapter must be included in the list of authorized Wireless PCs.
Internet Settings 57Internet Settings Before you can configure the Gateway, you need to know the IP information allocation method used by your ISP. There are four different ways that ISPs can allocate IP information, as described below:1 Static IP Address (DSL or Cable)The ISP provides the IP addressing information for you to enter manually. To configure the Gateway you will need to know the following:■IP Address■Subnet Mask■ISP Gateway■DNS address(es)2 Dynamic IP Address (DSL or Cable)Dynamic IP addressing (or DHCP) automatically assigns the Gateway IP information. This method is popular with Cable providers. This method is also used if your modem has a built in DHCP server.3 PPPoE (DSL only)If the installation instructions that accompany your modem ask you to install a PPPoE client on your PC, then select this option. To configure the Gateway you will need to know the following: ■Username■Password■Service Name (if required by your ISP)When you install the Gateway, you will not need to use the PPPoE software on your PC.4 PPTP (DSL or Cable)PPTP is only used by some European providers. If the installation instructions that accompany your modem ask you to setup a dialup connection using a PPTP VPN tunnel then select this option. To configure the Gateway you will need to know the following:■Username■Password■VPN Server address (usually your modem)
58 CHAPTER 5: GATEWAY CONFIGURATIONWhen you install the Gateway, you will not need to use the dialup VPN on your PC anymore.Connection to ISP Figure 40 Connection to ISP ScreenBefore beginning this section, ensure you have the required information from your ISP. (See “Before you Install your Gateway” on page 21.)Select Internet Settings from the main menu to display Connection to ISP (Figure 40). Choose an IP Allocation Mode from the drop down box.Select an IP Allocation Mode from the following:■Static IP address (to be specified manually) see page 59■Dynamic IP address (automatically allocated) see page 60■PPPoE (used by DSL providers only) see page 61■PPTP (used by some European providers) see page 62
Internet Settings 59Static IP AddressFigure 41 Connection Parameters Screen - Static IPTo setup the Gateway for use with a Static IP address connection:1Select Static IP Address (to be specified manually) in the IP Allocation Mode field (Figure 41).2Enter your IP Address in the IP Address text box.This information, along with the rest of the information in this screen, should be provided to you by your ISP. If the information is already entered, your ISP has pre-configured your Gateway, and you should go to step 7.3Enter your subnet mask in the Subnet Mask text box.4Enter your ISP Gateway address in the ISP Gateway Address text box.5Enter your primary DNS address in the Primary DNS Address text box.6Enter your secondary DNS address in the Secondary DNS Address text box.This step is optional. Not all ISPs require a secondary DNS address.7Check all of your settings, and then click Apply.
60 CHAPTER 5: GATEWAY CONFIGURATIONDynamic IP AddressFigure 42 Connection Parameters Screen - Dynamic IPIf this mode is selected, your IP Address, Subnet Mask, and DNS Address will be obtained automatically from your ISP. They are not displayed on this screen, but may be viewed on the Status screen (click on Status and Logs on the left hand menu bar). To setup the Gateway for use with a dynamic IP address connection:1Select Dynamic IP Address (automatically allocated) in the IP Allocation Mode field. (Figure 42)2Enter your Primary DNS Address and Secondary DNS address.Your ISP may provide you with primary and secondary DNS addresses. If they have been provided, enter the addresses in the appropriate text boxes. If not, leave 0.0.0.0 in the boxes.3Enter the Host Name (optional).Some ISPs require a host name. If your ISP has this requirement, enter the host name in the Host Name text box.4If you use ‘Cable’, your ISP may use your MAC address to authenticate you. If this is the case, you will need to ‘Clone’ your MAC address. There are three options:■Use the Gateway’s original Internet MAC address - This field is selected by default and is automatically filled in with the MAC address of the Gateway.

Navigation menu