Abocom Systems WR5501 802.11b/g/n Wireless Router User Manual WR5503 Manual Eng Generic ok

Abocom Systems Inc 802.11b/g/n Wireless Router WR5503 Manual Eng Generic ok

User Manual

802.11 b/g/n compliant Router User’s Manual
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.  Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: 1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
Table of Content CHAPTER 1: INTRODUCTION .............................................................................. 1Features ......................................................................................................................................... 1Physical Details ........................................................................................................................... 1CHAPTER 2: ABOUT OPERATION MODES ....................................................... 4Operation Modes ........................................................................................................................ 4Router Mode ................................................................................................................................ 4Access Point Mode ..................................................................................................................... 5Converter Mode .......................................................................................................................... 5CHAPTER 3: CONFIGURATION ........................................................................... 6Hardware Connection ............................................................................................................... 6Login ............................................................................................................................................... 6Setup Wizard ............................................................................................................................. 10Status ........................................................................................................................................... 16Network ....................................................................................................................................... 17Wireless ....................................................................................................................................... 27Firewall ........................................................................................................................................ 39Administration .......................................................................................................................... 46CHAPTER 4: PC CONFIGURATION ................................................................. 55Overview ..................................................................................................................................... 55Windows Clients ....................................................................................................................... 55Macintosh Clients ..................................................................................................................... 63Linux Clients .............................................................................................................................. 63Other Unix Systems ................................................................................................................. 64Wireless Station Configuration ........................................................................................... 64APPENDIX A: TROUBLESHOOTING ................................................................. 66Overview ..................................................................................................................................... 66General Problems ..................................................................................................................... 66Internet Access ......................................................................................................................... 66Wireless Access ........................................................................................................................ 67APPENDIX B: ABOUT WIRELESS LANS .......................................................... 69BSS (Basic Service Set) .......................................................................................................... 69Channels ...................................................................................................................................... 69Security ........................................................................................................................................ 69Wireless LAN Configuration ................................................................................................. 70
Chapter 1: Introduction 1Chapter 1: Introduction The 802.11b/g/n Wireless Router supports 4 ports 10/100M Ethernet for LAN and 1 port 10/100M Ethernet interface for WAN. With the advanced MIMO technology, it can support the data transmission rate 6 times more (up to 300 Mbps) and the coverage 3 times more than IEEE 802.11b/g devices. The Wireless Router enables your whole network sharing a high-speed cable or DSL Internet connection. With it, you can share a high-speed Internet connection, files, printers, and multi-player games at incredible speeds, without the hassle of stringing wires. It also offers easy configuration for your wireless network at home and presents wireless network of high functionality, security, and flexibility. Features 1. Support 4 ports 10/100M Ethernet for LAN and 1 port 10/100M Ethernet interface for WAN. 2. Clock rate up to 400MHz. 3. Support the IEEE 802.11n/b/g standard, high speed data rate up to 300Mbps, two transmit and two receive path(2T2R) 4. Supports WPS (Wi-Fi Protected Setup) with physical push button. 5. High security with build-in Security: WEP 64/128, WPA, WPA2, 802.1x and 802.11i. 6. Support Client, AP, WDS, AP+WDS mode. 7. Advanced Quality of Service (QoS), WMM. 8. Easy web broswer configuration for home user setup. Physical Details Top LEDs LED Behavior LED Printed Color Behavior Indication Power PWR Green ON Power on OFF Power off Internet WAN Green ON Internet link / active OFF Internet function off Blinking Internet traffic transmitting
Chapter 1: Introduction 2WPS WPS Green ON WPS setup successfully OFF WPS is disabled Blinking WPS is enabled to make a connection Wireless LAN WLAN Green OFF WLAN off ON WLAN link / active Blinking WLAN traffic transmitting LAN Green OFF LAN function off ON LAN link / active Blinking LAN traffic transmitting System SYS Green ON System is ready to login web server OFF System is not ready to login web server Blinking System is set to factory default Ports and Buttons Ports and buttons Ant. 1 Ant. 2 Install the appending antennas here. Reset z Press 2 seconds, the LED will be off. z Keep on pressing reset button 2~5 seconds, the system will reboot automatically. z Keep on pressing the reset button more than 5 seconds, the Wireless Router will set all setting back to factory default. LAN 1-4 Use standard LAN cables (RJ45 connectors) to connect your PCs to this port. If required, any port can be connected to another hub. Any LAN port will automatically function as an "Uplink" port when necessary.
Chapter 1: Introduction 3WAN Connect the ADSL or Cable Modem here with RJ45 cable. If your modem came with a cable, use the supplied cable, otherwise, use a standard LAN cable (RJ45 connectors). DC 5V Connect the supplied power adapter here. Side Panel WPS WPS To enable the WPS function press the physical WPS button on the Wireless Router once, then the LED will start to flash. Please make a connection with other WPS supported device within 2 minutes.
4 Chapter 2: About Operation Modes This device provides operational applications with Router, AP and Converter modes, which are mutually exclusive. This device is shipped with configuration that is functional right out of the box. If you want to change the settings in order to perform more advanced configuration or even change the mode of operation, you can MANUALLY switch to the mode you desired by the manufacturer as described in the following sections. Operation Modes You have to MANUALLY switch the bar into the mode you preferred, Router, AP or Converter modes, then the device will reboot automatically into the mode you have selected. Router Mode In this mode, the device is supposed to connect to internet via ADSL/Cable Modem. The NAT is enabled and PCs in LAN ports share the same IP address to ISP(Internet Service Provider) through WAN port. The connection type can be setup in PPPoE, DHCP client, PPTP client, L2TP client or static IP. The wireless connection will be set up from a point-to-point LAN into a point-to-multipoint WAN. This device connects all the stations (PC or notebook with wireless function) to a wireless network. All stations can have the Internet access if only the device has the Internet connection.
Chapter 2: About Operation Modes 5 Access Point Mode When acting as an Access Point (AP), this device connects all the stations (PC/notebook with wireless network adapter) to a wireless network. All stations can have the Internet access if only the Access Point has the Internet connection. Converter Mode If set to Converter mode, a device connects to each other through an access point or a base station (gateway or router.) This device can work like a wireless station when it’s connected to a computer directly, so that the computer can send packets from wired end to wireless interface.
6 Chapter 3: Configuration Hardware Connection Step 1. Connect one end of the Ethernet cable to the LAN port (1~4) of the Wireless Router, another end to your PC or notebook. Step 2. Connect Ethernet cable one end to the WAN (Internet) port of the Wireless Router, the other end to the ADSL or cable modem. Step 3. Finally, connect the Wireless Router with a power to an outlet. Login 1. Start your computer and make sure the connection by an Ethernet cable between your computer and the Wireless Router. 2. Start your Web Browser. 3. In the Address box, enter the IP address of the Wireless Router, as in this example, which uses the Wireless Router's default IP address: http://192.168.1.254
Chapter 3: Configuration 74. After connected successfully, the following screen will show up. Simply enter the username "admin" and password "password" to login. After login successfully, please click the Setup Wizard item that provides a primary configuration of this device. You may enter each screen to change the default settings step by step.
Chapter 3: Configuration 8If you cannot connect... If the Wireless Router does not respond, check the following: • The Wireless Router is properly installed, LAN connection is OK, and it is powered ON. You can test the connection by using the "Ping" command: • Please go to Start>Run…> Enter “cmd” command in the column to open the MS-DOS window. • Enter the command: ping 192.168.1.254 If no response is received, either the connection is not working, or your PC's IP address is not compatible with the Wireless Router's IP Address. (See next item.) • If your PC is using a fixed IP Address, its IP Address must be within the range 192.168.1.2 to 192.168.1.253 to be compatible with the Wireless Router's default IP Address of 192.168.1.253. Also, the Network Mask must be set to 255.255.255.0. See Chapter 4 - PC Configuration for details on checking your PC's TCP/IP settings. • Ensure that your PC and the Wireless Router are on the same network segment. (If you don't have a router, this must be the case.) • Ensure you are using the wired LAN interface. The Wireless interface can only be used if its configuration matches your PC's wireless settings.
Chapter 3: Configuration 9Common Connection Types The Internet connection type according to the ISP (Internet Service Provider) that you selected. Cable Modems Type Details ISP Data required Dynamic IP address Your IP address is allocated automatically, when you connect to you ISP. Usually, none. However, some ISP's may require you to use a particular Hostname, Domain name, or MAC (physical) address. Static (Fixed) IP address Your ISP allocates a permanent IP address to you. IP address allocated to you. Some ISP's may also require you to use a particular Hostname, Domain name, or MAC (physical) address. DSL Modems Type Details ISP Data required Dynamic IP address Your IP address is allocated automatically, when you connect to you ISP. None. Static (Fixed) IP address Your ISP allocates a permanent IP address to you. IP address allocated to you. PPPoE You connect to the ISP only when required. The IP address is usually allocated automatically. User name and password. Other Modems (e.g. 3.5G Wireless card) Type Details ISP Data required Dynamic IP address Your IP address is allocated automatically, when you connect to you ISP. The ISP's may require you to use a particular Hostname, Domain name, or MAC (physical) address.
Chapter 3: Configuration 10Setup Wizard The setup wizard will guide you to configure access point for first time. Please follow the setup wizard step by step. Step 1- WAN Access Type Here user can set up the WAN(Internet) connection type easily. Select the WAN Connection Type Static (Fixed IP), DHCP (Auto Config), PPPoE(ADSL), or 3G (DIAL) and click Next to continue.
Chapter 3: Configuration 11WAN Access Type DHCP Client If the DHCP Client be selected, the computer will obtain the IP address automatically. Static IP If the Static IP be selected, user have to set up the IP address, subnet mask and default gateway according to the ISP (Internet Service Provider) that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Default Gateway: Enter the default gateway IP address provided by your ISP here. Internet Primary DNS: Enter the DNS server IP address(es) that provided by your ISP, or you can specify your own preferred DNS server IP address(es). Internet Secondary DNS: Secondary DNS Server is optional. You can enter another DNS server’s IP address as a backup. PPPoE If the PPPoE (ADSL) be selected, user have to set up the user name and password according to the ISP (Internet Service Provider) that provided the related information. User Name: Enter the username that provide by your ISP (Internet Service Provider). Maximum input is 32 alphanumeric characters (case sensitive). Password: Enter the password that provide by your ISP (Internet Service Provider). Maximum input is 32 alphanumeric characters (case-sensitive). PPTP
Chapter 3: Configuration 12 If the PPTP be selected, users have to set up the server IP address, user name and password according to the ISP that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Server IP Address: Enter the PPTP Server IP Address in this column. User Name: Maximum input is 20 alphanumeric characters (case sensitive). Password: Maximum input is 32 alphanumeric characters (case sensitive). L2TP If the L2TP be selected, user have to set up the server IP address, user name and password according to the ISP that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Server IP Address: Enter the L2TP Server IP Address in this column. User Name: Maximum input is 20 alphanumeric characters (case sensitive). Password: Maximum input is 32 alphanumeric characters (case sensitive). Step 2- LAN Interface Setup This step can set up local area network of the Wireless Router, such as IP address, subnet mask, DHCP type, DHCP IP addresses range, DHCP subnet mask, DHCP DNS, default gateway and DHCP lease time.
Chapter 3: Configuration 13 IP Address Shows the IP address of the Wireless Router (Default IP address is 192.168.1.254.) Subnet Mask The subnet mask of the Wireless Router (Default subnet mask is 255.255.255.0.) Step 3- Wireless Basic Settings
Chapter 3: Configuration 14Band Select 2.4 GHz (B+G+N), 2.4 GHz (B), 2.4 GHz (G), 2.4 GHz (N), 2.4 GHz (B+G), and 2.4 GHz (G+N). SSID A SSID is referred to a network name because essentially it is a name that identifies a wireless network. Channel Width Select 20/40MHz or 20MHz for the transmitting band width. Channel Number Select 1~11 or Auto Select from the pull-down menu. Step 4- Security Here can set up the wireless security of the Wireless Router. Security Mode Select desired security type from the pull-down menu None, WEP, WPA, WPA2, WPA2 Mixed. The default setting is None. It is strongly recommend to set up security mode to prevent any unauthorized accessing. Both your computer and the Wireless Router must have the same settings for security. WEP Key Length: select key length 64-bit or 128-bit. Key Format: Select the Hex(10 characters) or ASCII (5 characters). z Hexadecimal (WEP 64 bits): 10 Hex characters (0~9, a~f).
Chapter 3: Configuration 15z Hexadecimal (WEP 128 bits): 26 Hex characters (0~9, a~f). z ASCII (WEP 64 bits): 5 ASCII characters (case-sensitive). z ASCII (WEP 128 bits): 13 ASCII characters (case-sensitive). Key Setting: Enter the key in the key setting field. WPA / WPA2 / WPA2-Mixed WPA Cipher Suite: here supported AES only. WPA2 Cipher Suite: here supported AES only. Pre-Shared Key Format: There are two formats for choosing to set the pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key : Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if you selected passphrase. Pre-shared key format to set the passwords or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used on client's end.
Chapter 3: Configuration 16Status
Chapter 3: Configuration 17Network LAN Interface Setup IP Address Shows the IP address of the Wireless Router (Default IP address is 192.168.1.254) Subnet Mask The subnet mask of the Wireless Router (Default subnet mask is 255.255.255.0.) Default Gateway Shows the default gateway of this Wireless Router. DHCP Mode Disable: Select to disable this Wireless Router to distribute IP addresses to connected clients. Server: Select to enable this Wireless Router to distribute IP addresses (DHCP Server) to connected clients. And the following field will be activated for you to enter the starting IP address. Client: Select the client mode to use the DHCP Client Range The starting address of this local IP network address pool. The pool is a piece of continuous IP address segment, the device will distribute IP addresses from 192.168.1.100 to 192.168.1.200 to all the computers in the network that request IP addresses from DHCP server (Router). The end IP address maximum is 253. Note: If “Continuous IP address pool starts” is set at 192.168.1.1 and the “Number of IP address in pool end” is 253, the device will distribute IP addresses from 192.168.1.100 to 192.168.1.253 to all the computers in the network that request IP addresses from DHCP server (Router).
Chapter 3: Configuration 18Click Show Client button to show Active DHCP Client Table. The table shows assigned IP address, MAC address and time expired for each client. Refresh: Click this button to refresh the table. Close: Click this button to close the window. Static DHCP Check the box to enable the Static DHCP function, default setting is disabled. When set to enabled, user can click Set Static DHCP button to set the Static DHCP function. IP Address: Enter the fixed IP address that DHCP Server assigned to a certain connected station. MAC Address: Enter the MAC address of a certain station, and then the DHCP Server will to distribute a fixed IP address to the station automatically once they connected. Comment: You can enter a comment to description above IP address or MAC address. Apply Changes: After completing the settings on this page, click Apply changes button to save the settings. Reset: Click Reset to restore to default values. Static DHCP List: Here shows the static IP address that have been assigned according to the MAC address. Delete Selected: Click Delete Selected to delete items which are selected. Delete All: Click Delete All button to delete all the items. Reset: Click Reset button to rest.
Chapter 3: Configuration 19Clone MAC Address This table displays you the station MAC information. Internet Service Setup WAN Access Type Select the WAN Access Type Static IP, DHCP Client, PPPoE, or PPTP or L2TP from the pull-down list. Default setting is DHCP Client enabled. DHCP Client
Chapter 3: Configuration 20 If the DHCP Client be selected, the computer will obtain the IP address automatically. Hostname: Enter the hostname that assigned IP address to your computer in this field. Maximum input is 32 alphanumeric characters (case sensitive).MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1492 for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. Select to Attain DNS Automatically or select Set DNS Manually to set the DNS server IP address at the following DNS 1~3 columns. Default setting is Attain DNS Automatically. DNS 1: Enter the DNS server IP address(es) provided by your ISP, or you can specify your own preferred DNS server IP address(es). DNS 2~3: This servers are optional. You can enter another DNS server’s IP address as a backup. DNS 2 and 3 servers will be used when the DNS 1 server fails. Static IP If the Static IP be selected, user have to set up the IP address, subnet mask and default gateway according to the ISP (Internet Service Provider) that
Chapter 3: Configuration 21provide the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Default Gateway: Enter the default gateway IP address provided by your ISP here. MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1492 for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. Select to Attain DNS Automatically or select Set DNS Manually to set the DNS server IP address at the following DNS 1~3 columns. Default setting is Attain DNS Automatically. DNS 1: Enter the DNS server IP address(es) provided by your ISP, or you can specify your own preferred DNS server IP address(es). DNS 2~3: This servers are optional. You can enter another DNS server’s IP address as a backup. DNS 2 and 3 servers will be used when the DNS 1 server fails. PPPoE If the PPPoE be selected, user have to set up the user name and password according to the ISP (Internet Service Provider) that provided the related information. User Name: Enter the username that provide by your ISP (Internet Service Provider). Maximum input is 32 alphanumeric characters (case sensitive). Password: Enter the password that provide by your ISP. Maximum input is 32 alphanumeric characters (case-sensitive). Service Name: Enter the Internet service provider’s name here.
Chapter 3: Configuration 22Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down menu. If selected Manual user can click Connect button to make a connection. Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000 minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected to Connect on Demand. MTU Size: MTU(Maximum Transmission Unit, namely the maximum packet size) for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect selection is entered, you may not be able to open certain web sites. DNS 1: Enter the DNS server IP address(es) provided by your ISP, or you can specify your own preferred DNS server IP address(es). DNS 2~3: This servers are optional. You can enter another DNS server’s IP address as a backup. DNS 2 and 3 servers will be used when the DNS 1 server fails. PPTP If the PPTP be selected, user have to set up the server IP address, user name and password according to the ISP that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Server IP Address: Enter the PPTP Server IP Address in this column. User Name: Maximum input is 20 alphanumeric characters (case sensitive).
Chapter 3: Configuration 23Password: Maximum input is 32 alphanumeric characters (case sensitive). Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down menu. If selected Manual user can click Connect button to make a connection. Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000 minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected to Connect on Demand. MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1460 for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. L2TP If the L2TP be selected, user have to set up the server IP address, user name and password according to the ISP that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Server IP Address: Enter the L2TP Server IP Address in this column. User Name: Maximum input is 20 alphanumeric characters (case sensitive). Password: Maximum input is 32 alphanumeric characters (case sensitive). Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down menu. If selected Manual user can click Connect button to make a connection.
Chapter 3: Configuration 24Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000 minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected to Connect on Demand. MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1460 for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. MAC Clone Your ISP (Internet Service Provider) may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in or click Fill my MAC to replace the WAN MAC address with the MAC address of that PC. Default setting is Disable. User can select Enable form the pull-down list, and click Fill my MAC button to fill in your PC’s MAC address in the blank field. Enable uPNP… Check to enable the listed functions. Apply After completing the settings on this page, click Apply button to save the settings. Cancel Click Cancel to restore to default values.
Chapter 3: Configuration 25 Advanced Routing If you connect several routers with this Wireless Router, you may need to set up a predefined routing rule to have more effective network topology/traffic, this is called static route between those routers and the Wireless Router. Enable Dynamic Route Check to enable the dynamic route function. NAT: Select to enable the network address translation function. Transmit: Select to use the Routing Information Protocol, the function will select the packet transmitting route that pass through least routers. Receive: Select to use the Routing Information Protocol, the function will select the packet receiving route that pass through least routers. Enable Static Route IP address: Enter the Gateway IP address in the field. Subnet Mask: Enter the Gateway subnet mask here. Gateway: Enter the gateway name or domain name here.
Chapter 3: Configuration 26Metric: The route with the lowest metric is the preferred route. Interface: Select to use LAN or WAN as the physical interface from where the packets will be sent. Destination The network address of the destination LAN segment. When a packet with destination IP address that matches to this field, it will route to the device set in the Route Gateway field. Range Select Host or Net from the pull-down menu. If select Net, please enter the Netmask in the following column. IP address Enter the Gateway IP address in the field. Interface You can Comment Enter note or remark here. Apply After completing the settings on this page, click Apply button to save the settings. Reset Click to discard current setting.
Chapter 3: Configuration 27 Wireless Basic Disable Wireless LAN Interface Check to disable the wireless function. If the wireless LAN interface be disabled, the WLAN LED on the front LED will be off. Band You can choose one mode of the following you need. z 2.4GHz (B): 802.11b supported rate only. z 2.4GHz (G): 802.11g supported rate only. z 2.4GHz (N): 802.11n supported rate only. z 2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. z 2.4GHz (G+N): 802.11g supported rate and 802.11n supported rate. z 2.4GHz (B+G+N): 802.11b, 802.11g and 802.11n supported rate. The default is 2.4GHz (B+G+N) mode. Mode Under Router operation mode, user can select AP, WDS, and AP+WDS from the pull-down list. For AP mode, user can select AP, Client, WDS and AP+WDS mode. Under client mode, there is only Client mode can be
Chapter 3: Configuration 28selected. Multiple APs This page shows and updates the wireless setting for multiple APs. User can set up the multiple AP here. Network Type If the mode be set to AP or Client mode that the network type can be set to Infrastructure or Ad hoc. SSID A SSID(Service Set Identifier) is referred to a network name because essentially it is a name that identifies a wireless network (case-sensitive). Channel Width Select 20MHz/40MHz channel width, the channel number will be form 5~11 and auto; Select 20MHz channel width the channel number will be form 1~11 and auto. Default is 20MHz/40MHz. Channel Selection The channel number base on the channel width you select. Broadcast SSID Enabled: This wireless AP will broadcast its SSID to stations. Disabled: This wireless AP will not broadcast its SSID to stations. If stations want to connect to this wireless AP, this AP’s SSID should be known in advance to make a connection. WMM The WiFi Multiple Media function is available under 2.4GHz (B), 2.4GHz (G) and 2.4GHz (B+G) band, and it is disabled under 2.4GHz (N), 2.4GHz (G+N) and 2.4GHz (B+G+N) band. Data Rate There are several data rate that you can select from the pull-down menu. Associated Clients Click Show Active Clients button to show all the listed active clients. Enable Mac Clone (Single Ethernet Client) This function will be enabled under Client mode.
Chapter 3: Configuration 29 Advanced Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network. If the 802.11g MIMO Wireless Router often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS Threshold RTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. If the “Hidden Node” problem is an issue, please specify the packet size. The RTS mechanism will be activated if the data size exceeds the value you set. Warning: Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Beacon Interval Beacon Interval is the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon. Range 20-1024 ms, default is 100. Preamble Type A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. You can select Long or Short for the preamble type.
Chapter 3: Configuration 30IAPP Select Enabled or Disabled to execute this function. Protection Select Enabled or Disabled to execute the security function. Aggregation Select Enabled or Disabled to execute this function. Short GI Select Enabled or Disabled to execute this function. WLAN Partition Select Enabled or Disabled to execute this function. RF Output Power Select the transmitting power rate 100%, 70%, 50%, 35%, 15%. Security Security Settings Select SSID Select SSID(Service Set Identifier) to set up the security form the pull-down list. Encryption elect desired security type from the pull-down menu None, WEP, WPA, WPA2, WPA2 Mixed. The default setting is None. It is strongly recommend to set up security mode to prevent any unauthorized accessing. Both your computer and the Wireless Router must have the same settings for security. Note: ¾ AUTO(Open/Shared) means AP can accept client(station) to connect to it by using OPEN-WEP or SHARED-WEP. WEP
Chapter 3: Configuration 31 Authentication: Select Open System, Shared Key or Auto. Key Length: select key length 64-bit or 128-bit. Key Format: z Hexadecimal (WEP 64 bits): 10 Hex characters (0~9, a~f). z Hexadecimal (WEP 128 bits): 26 Hex characters (0~9, a~f). z ASCII (WEP 64 bits): 5 ASCII characters (case-sensitive). z ASCII (WEP 128 bits): 13 ASCII characters (case-sensitive). Encryption Key: Enter the key in the key setting field. WPA-PSK/ WPA2-PSK/ WPA-PSK WPA2-PSK Authentication Mode: Select Enterprise (RADIUS) or Personal (Pre-Shared Key) mode. WPA Cipher Suite: here supported AES only. WPA2 Cipher Suite: here supported AES only. Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key : Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if you selected passphrase. Pre-shared key format to set the passwords or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used on client's end.
Chapter 3: Configuration 32ACL Wireless Access Control Mode Select Allow Listed or Deny Listed form the pull-down menu to enable access control function. Default setting is Disabled. MAC Address Enter the MAC address (12 characters) of a station that is allowed to access this Access Point. Comment You may enter up to 20 characters as a remark to the previous MAC address. Current Access Control List This table displays you the station MAC information. Delete Selected Click Delete Selected to delete items which are selected. Delete All Click Delete All to delete all the items. Reset Click Reset to rest. WDS Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS.
Chapter 3: Configuration 33 Step 1. Users would like to set up the WDS function, please go to Wireless > Basic page to set up the mode into WDS or AP+ WDS (Repeater) mode, and set the APs into the same Network Name(SSID) and Channel (If set to WDS mode, the SSID do not need to change). After setting up, please click Apply Changes button to execute. To use WDS function: 1. The APs must support WDS function. 2. To set the same SSID (Network name). 3. The channel must be set to the same on the APs. 4. To set the same Wireless MAC address (BSSID) on the APs. 5. To set same security (WEP or WPA) on the APs. Note ! To setup WDS must use the same wireless products (the same model will be better); due to different wireless products might support different WDS settings. Thus, it is suggested that to use the same wireless products that support WDS function.
Chapter 3: Configuration 34 Step 2. Then go to Wireless > WDS page to (1) enable the WDS function and (2) enter APs Wireless MAC address (please go to Status> Wireless Configuration to make sure the BSSID) to each other to make the WDS connection. Please click Apply button to execute. Enable WDS Check the box to enable the WDS function. 12123
Chapter 3: Configuration 35MAC Address MAC Address: Enter the Wireless BSSID (MAC) 12 characters of the wireless AP that you want to connect with. To check your wireless router’s MAC address, please go to Status > Wireless Configuration to find your BSSID (Wireless MAC address.) Data Rate Select the data rate form the pull-down list. Comment Enter a description for the device. Apply Changes After completing the settings on this page, click Apply changes button to save the settings. Reset Click Reset to restore to default values. Set Security Enable the WDS function and then click Set Security button to set up the WDS security. Encryption: Select the encryption type None, WEP 64 bits, WEP 128 bits, and WPA2(AES) from the pull-down menu. WEP Key Format: For WEP 64 bits and WEP 128 bits encryption type, the selection of WEP Key Format are Hex and ASCII. WEP Key: If select Hex if you are using hexadecimal numbers (0-9, or A-F). Select ASCII if you are using ASCII characters (case-sensitive). z Hexadecimal (WEP 64 bits): 10 Hex characters (0~9, a~f). z Hexadecimal (WEP 128 bits): 26 Hex characters (0~9, a~f). z ASCII (WEP 64 bits): 5 ASCII characters (case-sensitive). z ASCII (WEP 128 bits): 13 ASCII characters (case-sensitive). Pre-Shared Key Format: The Pre-shared Key Format will be enabled when WPA (TKIP) and WPA2 (AES) encryption be selected. There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key: Pre-Shared-Key serves as a password. Users may key in 8 to 63 characters string to set the passwords or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used on
Chapter 3: Configuration 36client's end. Show Statistics Click to show the current WDS AP table. This table shows the MAC address, transmission packets and errors, reception packets and Tx Rate (Mbps) counters for each configured WDS AP. Refresh: Click to renew the counters information. Close: Click to leave the screen. Current WDS AP List Here shows the current WDS AP information. Delete Selected Click Delete Selected to delete the selected AP information. Delete All Click Delete All to delete all the items. Reset Click Reset to restore the settings.
Chapter 3: Configuration 37WPS Disable WPS Check the box to disable the WPS function, default setting is enabled. WPS Status Here shows the current status of the WPS function. Default setting is Configured, click Reset to Unconfigured to re-configured the WPS connection. Self-PIN Number Here shows the 8 characters PIN code of the router itself. Push Button Configuration Click Start PBC button to make a WPS connection with client. Client PIN Number Enter the client PIN code into the blank field then click the Start PIN button to make a WPS connection with client.
Chapter 3: Configuration 38 Schedule Enable Wireless Schedule Check the box to enable the schedule function. Set up the time to schedule the wireless access rule. Select the day and time you want to enable the wireless function.
Chapter 3: Configuration 39 Firewall DMZ Settings Enable DMZ Check the box to enable DMZ function. If the DMZ Host Function is enabled, it means that you set up DMZ host at a particular computer to be exposed to the Internet so that some applications/software, especially Internet / online game can have two way connections. DMZ Host IP Address Enter the IP address of a particular host in your LAN which will receive all the packets originally going to the WAN port/Public IP address above. Note: You need to give your LAN PC clients a fixed/static IP address for DMZ to work properly. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values.
Chapter 3: Configuration 40URL Filter Settings Enable URL Filtering Check to enable URL filtering function. URL Address Enter the URL address in the field. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current URL address filter information. Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest.
Chapter 3: Configuration 41MAC Filtering Enable MAC Filtering Check to enable MAC filtering function. MAC Address Enter the client MAC address in the field. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current MAC filter information. Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest.
Chapter 3: Configuration 42Port Filtering Settings Enable Port Filtering Check to enable Port Filtering function. Port Range Enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Port Forwarding Table Shows the current Port Forwarding information. Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest.
Chapter 3: Configuration 43IP Filtering Enable IP Filtering Check to enable IP filtering function. Local IP Address Enter the local server’s IP address. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Comment You may key in a description for the port range. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current IP filter information. Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest.
Chapter 3: Configuration 44 Virtual Server Enable Port Forwarding Check to enable Port Forwarding function. IP Address Enter the IP address in the field. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Port Range For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Port Forwarding Table Shows the current Port Forwarding information. Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest.
Chapter 3: Configuration 45VLAN Enable VLAN Entries in below table are used to config vlan settings. VLANs are created to provide the segmentation services traditionally provided by routers. VLANs address issues such as scalability, security, and network management.
Chapter 3: Configuration 46Administration Password User Name To set up the login username to protect the Wireless Router configuration accessing via web browser. Empty user name and password will disable the protection. It’s strongly recommended to assign a set of password for further security. New Password To set up the login password to protect the Wireless Router configuration accessing via web browser. Maximum input is 30 alphanumeric characters (case sensitive.) Confirmed Password Key in the password again to confirm. Bandwidth Management
Chapter 3: Configuration 47 Enable QoS Entries in this table improve your online gaming experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web. Automatic Uplink/Download Speed Check the box to enable the automatic uplink/ download speed function. Manual Uplink/Download Speed You can manually enter the uplink/ download transmission rate in the blank field. Address Type Select IP or MAC address type. Local IP address MAC address Depend on the address type that selected, user can enter the IP address or MAC address of client to set up the bandwidth of the transmission. Port Enter the beginning of port range numbers used by the service. If
Chapter 3: Configuration 48the service uses a single port number, enter it in both the start and finish fields. Protocol Select the protocol (TCP, UDP, TCP/UDP, ICMP or ANY) used to the remote system or service. Mode Select Guaranteed minimum bandwidth or Restricted maximum bandwidth modes. Uplink Bandwidth (Kbps) Enter the Uplink Bandwidth (Kbps) in the column. Downlink Bandwidth (Kbps) Enter the Downlink Bandwidth (Kbps) in the column. Comment Enter the note for the setting.
Chapter 3: Configuration 49Denial of Service Enable DoS Prevention DoS (Denial of Service) attacks can flood your Internet connection with invalid packets and connection requests, using so much bandwidth and so many resources that Internet access becomes unavailable. The Wireless Router incorporates protection against DoS attacks. This screen allows you to configure DoS protection. Check the box to enable the DoS settings. Select All After you enabled the DoS prevention, you can click to select all DoS
Chapter 3: Configuration 50preventions. Clear All After you enabled the DoS prevention, you can click to uncheck all DoS preventions. Apply Changes After completing the settings on this page, click Apply Changes button to save current settings. NTP Current Time Enter the current time of this wireless router or click the Copy Computer Time button to synchronize the time with the connected computer automatically. Time Zone Select Select the local time zone from the pull-down menu. Enable NTP client update Check to enable NTP (Network Time Protocol Server) client update function. Automatically Adjust Daylight Saving Check the box to enable this function. NTP server Manual IP setting You may choose to select NTP server from the pull-down menu or enter an IP address of a specific server manually. Apply Changes After completing the settings on this page, click Apply Changes button to save current settings. Refresh Click Refresh button to renew current time.
Chapter 3: Configuration 51Dynamic DNS Setting Enable DDNS Check to enable the DDNS function. Service Provider Enter the DDNS Service Provider here. Domain Name Here shows the domain name of the service provider. User Name/Email Enter your email that you registered in service provider website. (You can refer to below Note information to apply a account form the service provider website.) Password/Key Enter your passwords that you registered in service provider website. Maximum input is 30 alphanumeric characters (case sensitive). Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values.
Chapter 3: Configuration 52Upgrade Firmware Firmware Version Here display the latest firmware version. Select File Click the Browse button to find and open the firmware file (the browser will display to correct file path.) Upload Click the Upload button to perform. Reset Click Reset button to restore to default values. Settings Management Save Settings to File Click the Save button to save the current settings file in the PC. Load Settings form File Click the Browse button to find and open the previous saved file (the browser will display to correct file path.) Then, click Upload button to upload the previous file. Reset Settings to Default Click Reset button to set the device back to default settings.
Chapter 3: Configuration 53Statistics This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks. System Log
Chapter 3: Configuration 54Enable Log Check to enable logging function. System all Activates all logging functions. Wireless Only logs related to the wireless LAN will be recorded. DoS Only logs related to the DoS protection will be recorded. Enable Remote Log Only logs related to the Remote control will be recorded. Log Server IP address Only logs related to the server will be recorded. Apply Changes After completing the settings on this page, click Apply Changes button to save current settings. Refresh Click Refresh button to renew the logs. Clear Click Clear button to delete the logs. Reboot Click the Reboot button to restart the Wireless Router.
Chapter 4: PC Configuration 55 Chapter 4: PC Configuration Overview For each PC, the following may need to be configured: • TCP/IP network settings • Internet Access configuration • Wireless configuration Windows Clients • This section describes how to configure Windows clients for Internet access via the Wireless Router. • The first step is to check the PC's TCP/IP settings. • The Wireless Router uses the TCP/IP network protocol for all functions, so it is essential that the TCP/IP protocol be installed and configured on each PC. TCP/IP Settings - Overview If using default Wireless Router settings, and default Windows TCP/IP settings, no changes need to be made. • By default, the Wireless Router will act as a DHCP Server, automatically providing a suitable IP address (and related information) to each PC when the PC boots. • For all non-server versions of Windows, the default TCP/IP setting is to act as a DHCP client. If using a Fixed (specified) IP address, the following changes are required: • The Gateway must be set to the IP address of the Wireless Router. • The DNS should be set to the address provided by your ISP (Internet Service Provider.)
Chapter 4: PC Configuration 56Checking TCP/IP Settings - Windows 2000 1. Go to Start > Control Panel > Network and Dial-up Connection. 2. Right click the Local Area Connection icon and select Properties. You should see a screen like the following: 3. Select the Internet Protocol (TCP/IP) protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct.
Chapter 4: PC Configuration 57Using DHCP • To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. • Restart your PC to ensure it obtains an IP address from the Wireless Router automatically. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. • Enter the Wireless Router 's IP address in the Default gateway field. (Your LAN administrator can advise you of the IP address they assigned to the Wireless Router.) • If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP. Checking TCP/IP Settings - Windows XP 1. Go to Start > Control Panel > Network Connection. 2. Right click the Local Area Connection icon and choose Properties. You should see a screen like the following: 3. Select the Internet Protocol (TCP/IP) protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following.
Chapter 4: PC Configuration 58 5. Ensure your TCP/IP settings are correct. Using DHCP • To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. • Restart your PC to ensure it obtains an IP address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. • In the Default gateway field, enter the Wireless Router 's IP address. Your LAN administrator can advise you of the IP address they assigned to the Wireless Router. • If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK. Checking TCP/IP Settings - Windows Vista 1. Go to Start > Control Panel> Network and Internet> Network and Sharing Center> Manage Network Connections> Local Area Connection. 2. Right click the Local Area Connection icon and choose Properties. You should see a screen like the following:
Chapter 4: PC Configuration 59 3. Select the Internet Protocol Version 4(TCP/IPv4) or 6 (TCP/IPv6) for your network card. 4. Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct.
Chapter 4: PC Configuration 60 Using DHCP • To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. • Restart your PC to ensure it obtains an IP address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. • In the Default gateway field, enter the Wireless Router 's IP address. Your LAN administrator can advise you of the IP address they assigned to the Wireless Router. • If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK. Checking TCP/IP Settings - Windows 7 1. Go to Start > Control Panel> Network and Sharing Center> Manage Network Connections> Local Area Connection. 2. Right click the Local Area Connection icon and choose Properties. You should see a screen like the following: 3. Select the Internet Protocol Version 4(TCP/IPv4) or 6 (TCP/IPv6) for your network card. 4. Click on the Properties button. You should then see a screen like the following.
Chapter 4: PC Configuration 61 5. Ensure your TCP/IP settings are correct. Using DHCP • To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. • Restart your PC to ensure it obtains an IP address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. • In the Default gateway field, enter the Wireless Router 's IP address. Your LAN administrator can advise you of the IP address they assigned to the Wireless Router. • If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK. Internet Access To configure your PCs to use the Wireless Router for Internet access: • Ensure that the ADSL modem, DSL modem, Cable modem, or other permanent connection is functional. • Use the following procedure to configure your Browser to access the Internet via the LAN, rather than by a Dial-up connection.
Chapter 4: PC Configuration 62For Windows 2000 1. Select Start menu> Settings> Control Panel > Internet Options. 2. Select the Connection tab, and click the Setup button. 3. Select "I want to set up my Internet connection manually, or I want to connect through a local area network (LAN)" and click Next. 4. Select "I connect through a local area network (LAN)" and click Next. 5. Ensure all of the boxes on the following Local area network Internet Configuration screen are unchecked. 6. Check the "No" option when prompted "Do you want to set up an Internet mail account now?" 7. Click Finish to close the Internet Connection Wizard Setup is now completed. For Windows XP 1. Select Start menu >Control Panel > Network and Internet Connections. 2. Select Set up or change your Internet Connection. 3. Select the Connection tab, and click the Setup button. 4. Cancel the pop-up "Location Information" screen. 5. Click Next on the "New Connection Wizard" screen. 6. Select "Connect to the Internet" and click Next. 7. Select "Set up my connection manually" and click Next. 8. Check "Connect using a broadband connection that is always on" and click Next. 9. Click Finish to close the New Connection Wizard Setup is now completed. For Windows Vista 1. Select Start menu > Control Panel > Network and Internet> Network and Sharing Center. 2. Select Set up a connection or network. 3. Select Connect to the Internet and click Next to continue. 4. Select Broadband (PPPoE). 5. Enter User name and Password that provided by the ISP, then click Connect to make a connection. For Windows 7 1. Select Start menu > Control Panel > Network Sharing Center. 2. Select Set up a new connection or network. 3. Select Connect to the Internet and click Next to continue. 4. Select Broadband (PPPoE). 5. Enter User name and Password that provided by the ISP, then click Connect to make a connection.
Chapter 4: PC Configuration 63Accessing AOL To access AOL (America On Line) through the Wireless Router, the AOL for Windows software must be configured to use TCP/IP network access, rather than a dial-up connection. The configuration process is as follows: 1. Start the AOL for Windows communication software. Ensure that it is Version 2.5, 3.0 or later. This procedure will not work with earlier versions. 2. Click the Setup button. 3. Select Create Location, and change the location name from "New Locality" to " Wireless Router ". 4. Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Number blank.) 5. Click Save, then OK. 6. Configuration is now complete. 7. Before clicking "Sign On", always ensure that you are using the " Wireless Router " location. Macintosh Clients From your Macintosh, you can access the Internet via the Wireless Router. The procedure is as follows. 1. Open the TCP/IP Control Panel. 2. Select Ethernet from the Connect via pop-up menu. 3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field can be left blank. 4. Close the TCP/IP panel, saving your settings. Note: If using manually assigned IP addresses instead of DHCP, the required changes are: • Set the Router Address field to the Wireless Router 's IP Address. • Ensure your DNS settings are correct. Linux Clients To access the Internet via the Wireless Router, it is only necessary to set the Wireless Router as the "Gateway". Ensure you are logged in as "root" before attempting any changes. Fixed IP Address By default, most Unix installations use a fixed IP Address. If you wish to continue using a fixed IP Address, make the following changes to your configuration. • Set your "Default Gateway" to the IP Address of the Wireless Router. • Ensure your DNS (Domain Name server) settings are correct. To act as a DHCP Client (Recommended) The procedure below may vary according to your version of Linux and X -windows shell. 1. Start your X Windows client. 2. Select Control Panel – Network. 3. Select the "Interface" entry for your Network card. Normally, this will be called "eth0". 4. Click the Edit button, set the "protocol" to "DHCP", and save this data. 5. To apply your changes:
Chapter 4: PC Configuration 64• Use the "Deactivate" and "Activate" buttons, if available. • OR, restart your system. Other Unix Systems To access the Internet via the Wireless Router: • Ensure the "Gateway" field for your network card is set to the IP Address of the Wireless Router. • Ensure your DNS (Name Server) settings are correct. Wireless Station Configuration • This section applies to all wireless stations (client end) wishing to use the Wireless Router as an access point, regardless of the operating system that is used on the client. • To use the Wireless Router, each wireless station must have compatible settings, as following: Mode The mode must be set to Infrastructure. SSID (ESSID) (Extended Service Set Identifier) The network name must match the value used on the Wireless Router. Note! The SSID(service set identifier) is case- sensitive. Disable If there is no security is enabled on the Wireless Router, the security of each station should be disabled as well. And, you can connect the Wireless Router without security, but it is NOT recommended. WEP Open System/ Shared Key/ Auto By default, WEP on the Wireless Router is disabled. Shared Key only supports WEP as encryption method. AUTO(Open/Shared) means AP can accept STA connect to it using OPEN-WEP or SHARED-WEP. • If WEP remains disabled on the Wireless Router, all stations must have WEP disabled. • If WEP is enabled on the Wireless Router, each station must use the same settings as the Wireless Router. Personal (Pre-Shared Key) WPA WPA2 WPA2-Mixed WPA-PSK(TKIP/AES)/ WPA2-PSK(TKIP/AES): If one of these securities is enabled on the Wireless Router. To make a connection, each station must use the same algorithms and pass phrase as the Wireless Router. Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter 64 characters string at a time. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key : Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if you selected passphrase. Pre-shared key format to set the passwords or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used
Chapter 4: PC Configuration 65on client's end. Enterprise (RADIUS) WPA WPA2 WPA2-Mixed 802.1x RADIUS Server: RADIUS is an authentication, authorization and accounting client-server protocol. The client is a Network Access Server that desires to authenticate its links. The RADIUS is a server that has access to a user database with authentication information. Each station must set up the RADIUS Server’s IP address, port and passwords that provided by your ISP. Note: By default, the Wireless Router will allow 802.11b, 802.11g and 802.11n connections.
Appendix A: Troubleshooting 66 Appendix A: Troubleshooting Overview This chapter covers some common problems that may be encountered while using the Wireless Router and some possible solutions to them. If you follow the suggested steps and the Wireless Router still does not function properly, contact your dealer for further advice. General Problems Problem 1: Can't connect to the Wireless Router to configure it. Solution 1: Check the following: • Check the Wireless Router is properly installed, LAN connections are OK, and it is powered ON. • Ensure that your PC and the Wireless Router are on the same network segment. • If your PC is set to "Obtain an IP address automatically" (DHCP client), please restart it. • If your PC uses a Fixed (Static) IP address, ensure that it is using an IP address within the range 192.168.1.1 to 192.168.1.253 and thus compatible with the Wireless Router's default IP Address of 192.168.1.254. Also, the Network Mask should be set to 255.255.255.0 to match the Wireless Router. In Windows, you can check these settings by using Control Panel-Network to check the Properties for the TCP/IP protocol. You can check Chapter 4: PC Configuration- TCP/IP settings for reference. Internet Access Problem 1: When I enter a URL or IP address I get a time out error. Solution 1: A number of things could be causing this. Try the following troubleshooting steps. • Check if other PCs work. If they do, ensure that your PCs IP settings are correct. If using a Fixed (Static) IP address, check the Network Mask, Default gateway and DNS as well as the IP address. • If the PCs are configured correctly, but still not working, check the Wireless
Appendix A: Troubleshooting 67Router. Ensure that it is connected and ON. Connect to it and check its settings. (If you can't connect to it, check the LAN and power connections.) • If the Wireless Router is configured correctly, check your Internet connection (ADSL/Cable modem) to see that it is working correctly. Problem 2: Some applications do not run properly when using the Wireless Router. Solution 2: The Wireless Router processes the data passing through it, so it is not transparent. Use the Filter Settings feature to allow the use of Internet applications, which do not function correctly. If this does solve the problem you can use the DMZ function. This should work with almost every application, but: • It is a security risk, since the firewall is disabled. • Only one (1) PC can use this feature. Wireless Access Problem 1: My PC can't locate the Wireless Router. Solution 1: Check the following: • Mode: Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure Mode) • SSID: The SSID(service set identifier) on your PC and the Wireless Router are the same. Remember that the SSID (service set identifier) is case-sensitive. So, for example "Workgroup" does NOT match "workgroup." • Security: Both your PC and the Wireless Router must have the same setting for security.  Disabled: The default setting for the Wireless Router security is disabled, so your wireless station should also has security disabled.  Enabled: If security is enabled on the Wireless Router, your PC must have security enabled, and the key must be matched.  It's strongly suggest to set up security that could prevent any unauthorized accessing to your wireless network. Setting WPA2 security is recommended that offers stronger security than WEP. Both your computer and the Wireless Router must have the same settings for security. • Channel: The wireless local area network is activated and configured by default. If necessary, please check and match channel for the terminal, for example, your notebook. Both your computer (client) and the Wireless Router must set to the same channel for connection. Problem 2: Wireless connection speed is very slow. Solution 2: The wireless system will connect at the highest possible speed, depending on the distance and the environment. To obtain the highest possible connection speed, you can experiment with the following: • Wireless Router location: Try adjusting the location and orientation of the
Appendix A: Troubleshooting 68Wireless Router. To see if radio interference is causing a problem, see if connection is possible when close to the Wireless Router. Remember that the connection range can be as little as 100 feet in poor environments. • Wireless Channels: If interference is the problem, changing to another channel may show a well improvement. • Radio Interference: Other devices may be causing interference. You can try to turn off other wireless devices, and see if this helps. Any "noisy" devices should be shielded or relocated. • RF Shielding: Your environment may tend to block transmission between the wireless stations. This will mean high access speed is only possible when close to the Wireless Router.
69 Appendix B: About Wireless LANs BSS (Basic Service Set) BSS (Basic Service Set) A group of wireless stations and a single access point, all using the same SSID(service set identifier), form a Basic Service Set (BSS). Using the same SSID (service set identifier) is essential. Devices with different SSIDs are unable to communicate with each other. Channels The wireless channel sets the radio frequency used for communication. • Access points use a fixed channel. You can select the channel used. This allows you to choose a channel which provides the least interference and best performance. In the USA and Canada, 11 channels are available. If using multiple access points, it is better if adjacent access points use different channels to reduce interference. • In "Infrastructure" mode, wireless stations normally scan all channels, looking for an access point. If more than one access point can be used, the one with the strongest signal is used. (This can only happen within an ESS(Extended Service Set)). • ESS: In Infrastructure mode, one or more BSS(Basic Service Set) can set up a ESS (Extended Service Set). User can access and roaming BSS data and the access point should be set to the same ESSID(Extended Service Set Identifier) to allow roaming. Note to US model owner: To comply with US FCC regulation, the country selection function has been completely removed from all US models. The above function is for non-US models only. Security WEP WEP(Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted. This is desirable because it is impossible to prevent snoopers from receiving any data which is transmitted by your wireless stations. But if the data is encrypted, then it is meaningless unless the receiver can decrypt it. If WEP is used, the wireless stations and the access point must have the same security settings for each of the following:
70WEP 64 Bits, 128 Bits. Key For 64 Bits encryption, the Key value must match. For 128 Bits encryption, the Key value must match. WEP Authentication Open System or Shared Key. WPA/ WPA2/ WPA-Mixed WPA/ WPA2 (Wi-Fi Protected Access) is more secure than WEP. It uses a “Shared Key” which allows the encryption keys to be regenerated at a specified interval. There are several encryption options: TKIP, AES, TKIP-AES and additional setup for RADIUS is required in this method. The most important features beyond WPA to become standardized through 802.11i/WPA2 are: pre-authentication, which enables secure fast roaming without noticeable signal latency. If WPA or WPA2 is used, the wireless stations and access point must have the same security settings. Wireless LAN Configuration To allow wireless stations(STA) to access the access point(AP), the wireless stations and the access point must use the same settings, as follows: Mode The mode must be set to Infrastructure. SSID (ESSID) (Extended Service Set Identifier) The network name must match the value used on the Wireless Router. Note! The SSID(service set identifier) is case- sensitive. Disable If there is no security is enabled on the Wireless Router, the security of each station should be disabled as well. And, you can connect the Wireless Router without security, but it is NOT recommended. WEP Open System/ Shared Key/ Auto By default, WEP on the Wireless Router is disabled. Shared Key only supports WEP as encryption method. AUTO(Open/Shared) means AP can accept STA connect to it using OPEN-WEP or SHARED-WEP. • If WEP remains disabled on the Wireless Router, all stations must have WEP disabled. • If WEP is enabled on the Wireless Router, each station must use the same settings as the Wireless Router. Personal (Pre-Shared Key) WPA WPA2 WPA2-Mixed WPA-PSK(TKIP/AES)/ WPA2-PSK(TKIP/AES): If one of these securities is enabled on the Wireless Router. To make a connection, each station must use the same algorithms and pass phrase as the Wireless Router. Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter 64 characters string at a time. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key: Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if you selected passphrase. Pre-shared key format to set the passwords or leave it blank, in which the 802.1x authentication will be activated. Make sure the same password is used
71on client's end.

Navigation menu