Abocom Systems WAP257 Wireless 802.11b/g High Power PoE Access Point User Manual WAP257mnl

Abocom Systems Inc Wireless 802.11b/g High Power PoE Access Point WAP257mnl

UserManual.wiki >

Abocom Systems >

WAP257 User Manual

Users Manual

802.11 b/g Access Point User’s Guide

- Table of Content TUIntroductionUT ............................................................................................................................ 1 TUFEATURESUT ............................................................................................................................. 1 TUAPPLICATIONUT ......................................................................................................................... 2 TUPARTS NAMES AND FUNCTIONSUT ............................................................................................ 3 TUFACTORY DEFAULT SETTINGSUT ............................................................................................... 5 TUWireless APUT....................................................................................................................... 5 TUHardware ConnectionUT ............................................................................................................ 6 TU Check the LEDs:UT ............................................................................................................... 7 TUAbout the Operation ModesUT .................................................................................................. 8 TU ACCESS POINT MODEUT ............................................................................................................ 8 TUWDS REPEATER MODEUT ......................................................................................................... 8 TU CLIENT MODE (INFRASTRUCTURE)UT ....................................................................................... 9 TU CLIENT MODE (AD-HOC)UT ...................................................................................................... 9 TUWDS BRIDGE MODEUT ............................................................................................................. 9 TUConfigurationUT ........................................................................................................................ 10 TULOGINUT .................................................................................................................................. 10 TUSTATUSUT................................................................................................................................11 TUSystemUT ............................................................................................................................. 11 TUStatisticsUT .......................................................................................................................... 12 TUWIRELESSUT ............................................................................................................................ 13 TUBasic SettingsUT.................................................................................................................. 13 TUAdvanced SettingsUT ........................................................................................................... 14 TUSecurityUT ........................................................................................................................... 18 TUAccess ControlUT ................................................................................................................ 20 TUTCP/IPUT ................................................................................................................................22 TUBasicUT ............................................................................................................................... 22 TUOTHERUT ................................................................................................................................. 24 TUUpgrade FirmwareUT ......................................................................................................... 24 TUSave/Reload SettingsUT....................................................................................................... 25 TUPasswordUT ........................................................................................................................ 27 TUSystem LogUT ...................................................................................................................... 27

1INTRODUCTION This is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless Access Point. The Wireless Access Point is equipped with two 10/100 M Auto-sensing Ethernet ports for connecting to LAN and also for cascading to next Wireless Access Point. This Access Point provides 64/128bit WEP encryption, WPA and IEEE802.1x which ensures a high level of security to protect users’ data and privacy. The MAC Address filter prevents the unauthorized MAC Addresses from accessing your Wireless LAN. Your network security is therefore double assured. The web-based management utility is provided for easy configuration that your wireless network connection is ensured to be always solid and hassle free. Features • Two LAN ports for Wireless AP cascade • Support WPA • Support AP client mode • Support WDS for bridge mode • Support data rate automatic fallback • Automatic channel selection • Client access control • Support 802.1x/Radius client with EAP-TLS, TKIP, AES encryption • Support IAPP • Adjustable Tx power, Tx rate, and SSID broadcast • Allow WEP 64/128 bit • Web interface management • Support System event log and statistics • MAC filtering (For wireless only) • Support High power • Support POE (Power Over Ethernet), which enables an Ethernet network cable to deliver both data and power

2Application Example 1 Example 2

3Parts Names and Functions 1. Front Panel: (LED Indicators) LED Status Indicator Color Solid Flashing 1 Power Green Turns solid green when the power is applied to this device. N/A. 2 Status Red Turns solid red when the device is booting. After booting successfully, the light will be turned off. Link/Act. Green Turns solid green when wireless interface is turned on. Receiving/ Sending data WEP/WPA Orange Turns solid orange when wireless security is enabled. N/A 3~6 Wireless MAC Ctrl Orange Turns solid orange when MAC Control is enabled. N/A

4 WDS Orange Turns solid orange when WDS is enabled. N/A 7 LAN 1 8 LAN 2 Green Turns solid green when linked to a local network. Receiving/ Sending data Table 1: LED Indicators 2. Rear Panel: Connection Ports Port/button Functions A 12V DC Connects the power adapter plug B LAN2 (PoE 48V) Connects to Ethernet C LAN1 Connects to Ethernet D (Factory) RESET Press for less than 5 seconds to reboot this device. Press for over 5 seconds to restore factory settings. Performing the Factory Reset will erase all previously device settings. Table 2: Connection Ports

5Factory Default Settings Setting Wireless Access Point Device Name Wireless AP SSID Default value: 802.11g-AP Channel 11 WEP Default value: Disabled IP Address 192.168.1. 254 

6HARDWARE CONNECTION Note: Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is placed, the better will the performance be. Connection of using the included Power adapter: 1. Connect to your local area network: connect a Ethernet cable to one of the Ethernet port (LAN1 or LAN2) of this Wireless Access Point, and the other end to a hub, switch, router, or another wireless access point. 2. Power on the device: Connect the included AC power adapter to the Wireless Access Point’s power port and the other end to a wall outlet. Connection of using PoE: The hardware connection is basically the same as using a power adapter to supply power to your wireless access point, except for a different power origin it gains. With PoE, your

7wireless access point gains power from a PSE device through simply an Ethernet UTP cable! Check the LEDs: The Power and LAN # LEDs should be ON. LAN# LED will even blink if there is traffic. The Link/Act LED will be on in static when wireless interface is turned on. If the Status LED glows after self-test , it means this Wireless Access Point fails on self test. Please ask your dealer for technical support. 3. Configure your PC: Make sure your local PC(s) has wireless network adapter installed. S

8ABOUT THE OPERATION MODES This device provides four operational applications with Access Point, Bridge, Client (Ad-hoc) and Client (Infrastructure) modes, which are mutually exclusive. This device is shipped with configuration that is functional right out of the box. If you want to change the settings in order to perform more advanced configuration or even change the mode of operation, you can use the web-based utility provided by the manufacturer as described in the following sections. Access Point Mode When acting as an access point, this device connects all the stations (PC/notebook with wireless network adapter) to a wired network. All stations can have the Internet access if only the Access Point has the Internet connection. WDS Repeater Mode While acting as Bridges, AP1 (with Station 1 being associated to) and AP2 (with Station 2 being associated) can communicate with each other through wireless interface (with WDS). Thus Station 1 can communicate with Station 2 and both Station 1 and Station 2 are able to access the Internet if only AP1 or AP2 has the Internet connection.

9Client Mode (Infrastructure) If set to Client (Infrastructure) mode, this device can work like a wireless station when it’s connected to a computer so that the computer can send packets from wired end to wireless interface. Client Mode (Ad-hoc) If set to the Client (Ad-hoc) mode, this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface. You can share files and printers between wireless stations (PC and laptop with wireless network adapter installed). WDS Bridge Mode The WDS (Wireless Distributed System) function lets this access point act as a wireless LAN access point and repeater at the same time. Users can use this feature to build up a large wireless network in a large space like airports, hotels and schools …etc. This feature is also useful when users want to bridge networks between buildings where it is impossible to deploy network cable connections between these buildings.

10CONFIGURATION Login 1. Start your computer. Connect an Ethernet cable between your computer and the Wireless Access Point. 2. Make sure your wired station is set to the same subnet as the Wireless Access Point, i.e. 192.168.1.254 3. Start your WEB browser. In the Address box, enter the following: HTTP://192.168.1.254 The configuration menu is divided into four categories: Status, Wireless, TCP/IP, and Other settings. Click on the desired setup item to expand the page in the main navigation page. The setup pages covered in this utility are described below. No password required for the first login (the default setting), just enter the User name 'admin' which is systematically fixed. Afterwards, you can assign a password for a security consideration without changing the fixed user name.

11Status In this screen, you can see the current settings and status of this Access Point. You can change settings by selecting specific tab described in below. USystem System Uptime The time period since the device was up. Firmware Version The current version of the firmware installed in this device. Wireless Configuration Wireless Mode There are four modes supported, Access Point, Client (Ad-hoc and Infrastructure), WDS Bridge and WDS repeater. The default mode is Access Point. If you want to change to bridge mode, please go to Wireless/WDS Setting to enable the WDS function. SSID The SSID differentiates one WLAN from another, therefore, all access points and all devices attempting to connect to a specific WLAN must use the same SSID. It is case-sensitive and must not exceed 32 characters. A device will not be permitted to join the BSS unless it can provide the unique

12SSID. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network. Channel Number The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel. Encryption WEP Encryption (Wired Equivalent Privacy) is set to Disabled by default. When WEP is enabled, data packet is encrypted before being transmitted. The WEP prevents data packets from being eavesdropped by unrelated people. By using WEP data encryption, there may be a significant degradation of the data throughput on the wireless link. Associated Clients Displays the total number of clients associated to this AP. You can have up to 64 clients to associate to this Access Point. BSSID BSSID displays the ID of current BSS, which uniquely identifies each BSS. In AP mode, this value is the MAC address of this Access Point. TCP/IP Configuration IP Protocol Display the method to get the IP of this AP, which could be obtained by Fixed-IP or DHCP-client. br0 IP Address Current IP address for this Access Point br0 Subnet Mask Current Subnet mask for this Access Point br0 Default Gateway Default Gateway for this Access Point br0 MAC Address The MAC Address for this Access Point UStatistics The Statistics table shows the packets sent/received over wireless and ethernet LAN respectively.

13Wireless UBasic Settings This page includes all primary and major parameters. Any parameter change will cause the device to reboot for the new settings to take effect.  Disable Wireless LAN Interface Check the box to disable the Wireless LAN Interface, by so doing, you won’t be able to make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. Band You can choose one mode of the following you need.  2.4GHz (B): 802.11b supported rate only.  2.4GHz (G): 802.11g supported rate only.  2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. The default is 2.4GHz (B+G) mode. Mode This Wireless Access Point can support four

14modes AP, Client, Bridge and Repeater. Network Type When in Client mode, you can select between Ad-Hoc and Infrastructure. SSID The SSID differentiates one WLAN from another, therefore, all access points and all devices attempting to connect to a specific WLAN must use the same SSID. It is case-sensitive and must not exceed 32 characters. A device will not be permitted to join the BSS unless it can provide the unique SSID. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network. Channel Number Allow user to set the channel manually or automatically. If set channel manually, just select the channel you want to specify. If “Auto” is selected, user can set the channel range to have Wireless Access Point automatically survey and choose the channel with best situation for communication. The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel. Enable Mac Clone (Single Ethernet Client) If your ISP restricts service to PCs only, use the MAC Clone feature to copy a PC Media Access Control (MAC) address to your router. This procedure will cause the router to appear as a single PC, while allowing online access to multiple computers on your network. Apply Changes Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change. UAdvanced Settings It is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance

15 Authentication Type To provide a certain level of security, the IEEE 802.11 standard has defined two types of authentication methods, Open System and Shared Key. With Open System authentication, a wireless PC can join any network and receive any messages that are not encrypted. With Shared Key authentication, only those PCs that possess the correct authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an Open System network. Wired Equivalent Privacy (WEP) data encryption is used when the wireless devices are configured to operate in Shared Key authentication mode. If the Access Point is using Open System, then the wireless adapter will need to be set to the same authentication mode. Shared Key is used when both the sender and the recipient share a secret key. Select TAutoT for the network adapter to select the Authentication mode automatically depending on the Access

16Point Authentication mode. Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network. If your 802.11g Wireless LAN PC Card often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS Threshold RTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. “Hidden Node” is a situation in which two stations are within range of the same Access Point, but are not within range of each other. Therefore, they are hidden nodes for each other. When a station starts data transmission with the Access Point, it might not notice that the other station is already using the wireless medium. When these two stations send data at the same time, they might collide when arriving simultaneously at the Access Point. The collision will most certainly result in a loss of messages for both stations. Thus, the RTS Threshold mechanism provides a solution to prevent data collisions. When you enable RTS Threshold on a suspect “hidden station”, this station and its Access Point will use a Request to Send (RTS). The station will send an RTS to the Access Point, informing that it is going to transmit the data. Upon receipt, the Access Point will respond with a CTS message to all station within its range to notify all other stations to defer transmission. It will also confirm the requestor station that the Access Point has reserved it for the time-frame of the requested transmission. If the “Hidden Node” problem is an issue, please specify the packet size. UThe RTS mechanism will be activated if the data size exceeds the value you set.U. The default value is 2347. Warning: Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Beacon Interval Beacon Interval is the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point). Data Rate By default, the unit adaptively selects the highestpossible

17rate for transmission. Select the basic rates to be used among the following options: Auto, 1, 2, 5.5, 11or 54 Mbps. For most networks the default setting is Auto which is the best choice. When Auto is enabled the transmission rate will select the optimal rate. If obstacles or interference are present, the system will automatically fall back to a lower rate. Preamble Type A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. In a "noisy" network environment, the Preamble Type should be set to Long Preamble. The Short Preamble is intended for applications where minimum overhead and maximum performance is desired. If in a "noisy" network environment, the performance will be decreased. Broadcast SSID Select enabled to allow all the wireless stations to detect the SSID of this Access Point. IAPP IAPP (Inter Access Point Protocol) is designed for the enforcement of unique association throughout a ESS (Extended Service Set) and a secure exchange of station’s security context between current access point (AP) and new AP during handoff period. 802.11g Protection The 802.11g standard includes a protection mechanism to ensure mixed 802.11b and 802.11g operations. If there is no such kind of mechanism exists, the two kinds of standards may mutually interfere and decrease network’s performance. Tx Power Level Select the Transmission rate level ranging from Highest, High, Middle, Low and Lowest. Apply Change Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change. U

18Security Here you can configure the security of your wireless network. Selecting different method will enable you to have different level of security. Please note that by using any encryption, by which data packet is encrypted before transmission to prevent data packets from being eavesdropped by unrelated people, there may be a significant degradation of the data throughput on the wireless link. Encryption: None ( Encryption is set to None by default. ) If Use 802.1x Authentication is selected, the RADIUS Server will proceed to check the 802.1x Authentication. Encryption: WEP If WEP is selected, users will have to Set WEP keys either manually, or select to Use 802.1x Authentication to make the RADIUS server to issue the WEP key dynamically.

19 Set WEP key  Click the Set WEP Keys will prompt you a window to set 64bit or 128bit Encryption.  Select HEX if you are using hexadecimal numbers (0-9, or A-F). Select ASCII if you are using ASCII characters (case-sensitive).  Ten hexadecimal digits or five ASCII characters are needed if 64-bit WEP is used; 26 hexadecimal digits or 13 ASCII characters are needed if 128-bit WEP is used. Encryption: WPA (TKIP) WPA (TKIP): If WPA is selected, users will have to select the Authentication modes between Enterprise (RADIUS) and Personal (Pre-shared Key). Pre-shared Key Pre-Shared-Key serves as a password. Users may key in a 8 to 63 characters string to set the password or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used on client's end. There are two formats for choice to set the Pre-shared key, i.e. Passphrase and Hex. If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended.

20Group Key Life Time Enter the number of seconds that will elapse before the group key change automatically. The default is 86400 seconds. Enable Pre-Authentication The two most important features beyond WPA to become standardized through 802.11i/WPA2 are: pre-authentication, which enables secure fast roaming without noticeable signal latency. Preauthentication provides a way to establish a PMK security association before a client associates. The advantage is that the client reduces the time that it's disconnected to the network. Authentication RADIUS Server Port: Enter the RADIUS Server’s port number provided by your ISP. The default is 1812. IP Address: Enter the RADIUS Server’s IP Address provided by your ISP. Password: Enter the password that the AP shares with the RADIUS Server. Apply Change Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change. UAccess Control When Enable Wireless Access Control is checked, only those clients whose wireless MAC addresses listed in the access control list can access this Access Point. If the list contains no entries with this function being enabled, then no clients will be able to access this Access Point.

21 Wireless Access ControlMode Select the Access Control Mode from the pull-down menu. Disable: Select to disable Wireless Access Control Mode. Allow Listed: Only the stations shown in the table can associate with the AP. Deny Listed: Stations shown in the table won’t be able to associate with the AP. MAC Address Enter the MAC Address of a station that is allowed to access this Access Point. Comment You may enter up to 20 characters as a remark to the previous MAC Address. Apply Changes Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change. Delete Selected To delete clients from access to this Access Point, you may firstly check the Select checkbox next to the MAC address and Comments, and press Delete Selected. Delete All To delete all the clients from access to this Access Point, just press Delete All without selecting the checkbox. Reset If you have made any selection, press Reset will clear all the select mark.

22TCP/IP UBasic In this page, you can change the TCP/IP settings of this Access Point, select to enable/disable the DHCP Client, 802.1d Spanning Tree, and Clone MAC Address. IP Address This field can be modified only when DHCP Client is disabled. If your system manager assigned you static IP settings, then you will have to enter the information provided. Subnet Mask Enter the information provided by your system manager. Default Gateway Enter the information provided by your system manager. DHCP Select Disable, Client or Server from the pull-down menu. Disable: Select to disable DHCP server function. Client: Select to automatically get the LAN port IP address from ISP (For ADSL/Cable Modem). Server: Select to enable DHCP server function. DHCP Client Range 253 IP addresses continuing from 192.168.1.1 to 192.168.1.253 Show Client Click to show Active DHCP Client table. DNS Server Enter the Domain Name Service IP address.

23 802.1d Spanning Tree To enable 802.1d Spanning Tree will prevent the network from infinite loops. Infinite loop will happen in the network when WDS is enabled and there are multiple active paths between stations.S Clone MAC Address You can specify the MAC address of your Access Point to replace the factory setting. Apply Change Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change.

$24Other UUpgrade Firmware 1. Download the latest firmware from your distributor and save the file on the hard drive. 2. Start the browser, open the configuration page, click on Other, and click Upgrade Firmware to enter the Upgrade Firmware window. Enter the new firmware’s path and file name (i.e. C:\FIRMWARE\firmware.bin). Or, click the Browse button, find and open the firmware file (the browser will display to correct file path). 3. Click Reset to clear all the settings on this page. Or click Upload to start the upgrade.$

25USave/Reload Settings This function enables users to save the current configurationSsS as a file (i.e. config.dat) To load configuration from a file, enter the file name or click Browse… to find the file from your computer. Save Settings to File: Click SAVE.. to save the current configuration to file. When prompted the upper left screen, select “Save this file to disk”, and the upper right screen will prompt you a dialog box to enter the file name and the file location. S Load Settings From File: Click Browse… if you want to load a pre-saved file, enter the file name with the correct path and then click on Upload. Or click Browse… to select the file.

26 Reset: Click to restore the default configuration. U

27Password For secure reason, it is recommended that you set the account to access the web server of this Access Point. Leaving the user name and password blank will disable the protection. The login screen prompts immediately once you finish setting the account and password. Remember your user name and password for you will be asked to enter them every time you access the web server of this Access Point. New Password Set your new password. Password can be up to 30 characters long. Password can contain letter, number and space. It is case sensitive. Confirm Password Re-enter the new password for confirmation. Apply Change Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change. USystem Log This page display log events with time when events happened, log events’ types, log sources and the description for events themselves. System manager can use the system log to trace when problems occur.

28 Enable Log Select System all or Wireless only. Apply Changes Press to save the new settings on the screen. Refresh Click to refresh the screen. Clear Click to clear the current setting.

Navigation menu