ASUSTeK Computer RTACHC00 Wireless-AC1750 Dual Band Gigabit Router,Wireless-AC1900 Dual Band Gigabit Router User Manual Part 2
ASUSTeK Computer Inc Wireless-AC1750 Dual Band Gigabit Router,Wireless-AC1900 Dual Band Gigabit Router Users Manual Part 2
Contents
- 1. Users Manual Part 1
- 2. Users Manual Part 2
- 3. User Manual - Part 1
- 4. User Manual - Part 2
Users Manual Part 2
![714.4 IPv6This wireless router supports IPv6 addressing, a system that supports more IP addresses. This standard is not yet widely available. Contact your ISP if your Internet service supports IPv6. To set up IPv6:1. From the navigation panel, go to Advanced Settings > IPv6.2. Select your Connection Type. The conguration options vary depending on your selected connection type.3. Enter your IPv6 LAN and DNS settings.4. Click Apply.NOTE: Please refer to your ISP regarding specic IPv6 information for your Internet service.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-1.png)
![724.5 VPN ServerVPN (Virtual Private Network) provides a secure communication to a remote computer or remote network using a public network such as the Internet.NOTE: Before setting up a VPN connection, you would need the IP address or domain name of the VPN server you are trying to access.To set up access to a VPN server:1. From the navigation panel, go to Advanced Settings > VPN Server.2. On the Enable PPTP Server eld, select Yes.3. On the Network Place (Samba) Support eld, select Yes.4. Enter the user name and password for accessing the VPN server. Click the button.5. Click Apply.NOTE: For advanced VPN server settings, click the VPN Server tab to congure broadcast support, authentication, MPPE Encryption, and Client IP address range.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-2.png)
![734.6 FirewallThe wireless router can serve as a hardware rewall for your network. NOTE: The Firewall feature is enabled by default.4.6.1 GeneralTo set up basic Firewall settings:1. From the navigation panel, go to Advanced Settings > Firewall > General tab.2. On the Enable Firewall eld, select Ye s.3. On the Enable DoS protection, select Ye s to protect your network from DoS (Denial of Service) attacks though this may aect your router’s performance. 4. You can also monitor packets exchanged between the LAN and WAN connection. On the Logged packets type, select Dropped, Accepted, or Both.5. Click Apply.4.6.2 URL FilterYou can specify keywords or web addresses to prevent access to specic URLs.NOTE: The URL Filter is based on a DNS query. If a network client has already accessed a website such as http://www.abcxxx.com, then the website will not be blocked (a DNS cache in the system stores previously visited websites). To resolve this issue, clear the DNS cache before setting up the URL Filter.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-3.png)
![74To set up a URL lter:1. From the navigation panel, go to Advanced Settings > Firewall > URL Filter tab.2. On the Enable URL Filter eld, select Enabled.3. Enter a URL and click the button.4. Click Apply.4.6.3 Keyword lterKeyword lter blocks access to webpages containing specied keywords.To set up a keyword lter:1. From the navigation panel, go to Advanced Settings > Firewall > Keyword Filter tab.2. On the Enable Keyword Filter eld, select Enabled.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-4.png)
![753. Enter a word or phrase and click the Add button.4. Click Apply.NOTES:• The Keyword Filter is based on a DNS query. If a network client has already accessed a website such as http://www.abcxxx.com, then the website will not be blocked (a DNS cache in the system stores previously visited websites). To resolve this issue, clear the DNS cache before setting up the Keyword Filter.• Web pages compressed using HTTP compression cannot be ltered. HTTPS pages also cannot be blocked using a keyword lter.4.6.4 Network Services FilterThe Network Services Filter blocks LAN to WAN packet exchanges and restricts network clients from accessing specic web services such as Telnet or FTP.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-5.png)
![76To set up a Network Service lter:1. From the navigation panel, go to Advanced Settings > Firewall > Network Service Filter tab.2. On the Enable Network Services Filter eld, select Yes.3. Select the Filter table type. Black List blocks the specied network services. White List limits access to only the specied network services.4. Specify the day and time when the lters will be active. 5. To specify a Network Service to lter, enter the Source IP, Destination IP, Port Range, and Protocol. Click the button.6. Click Apply.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-6.png)
![774.7 Administration4.7.1 Operation ModeThe Operation Mode page allows you to select the appropriate mode for your network.To set up the operating mode:1. From the navigation panel, go to Advanced Settings > Administration > Operation Mode tab.2. Select any of these operation modes:• Wireless router mode (default): In wireless router mode, the wireless router connects to the Internet and provides Internet access to available devices on its own local network.• Access Point mode: In this mode, the router creates a new wireless network on an exising network. 3. Click Apply.NOTE: The router will reboot when you change the modes.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-7.png)
![784.7.2 SystemThe System page allows you to congure your wireless router settings.To set up the System settings:1. From the navigation panel, go to Advanced Settings > Administration > System tab.2. You can congure the following settings:• Change router login password: You can change the password and login name for the wireless router by entering a new name and password.• WPS button behavior: The physical WPS button on the wireless router can be used to activate WPS or switch o wireless networking. • Time Zone: Select the time zone for your network.• NTP Server: The wireless router can access a NTP (Network time Protocol) server in order to synchronize the time.• Enable Telnet: Click Yes to enable Telnet services on the network. Click No to disable Telnet.• Authentication Method: You can select HTTP, HTTPS, or both protocols to secure router access.• Enable Web Access from WAN: Select Yes to allow devices outside the network to access the wireless router GUI settings. Select No to prevent access.• Only allow specic IP: Click Yes if you want to specify the IP addresses of devices that are allowed access to the wireless router GUI settings from WAN. • Client List: Enter the WAN IP addresses of networking devices allowed to access the wireless router settings. This list will be used if you clicked Yes in the Only allow specic IP item.3. Click Apply.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-8.png)
![794.7.3 Firmware UpgradeNOTE: Download the latest rmware from the ASUS website at http://www.asus.comTo upgrade the rmware:1. From the navigation panel, go to Advanced Settings > Administration > Firmware Upgrade tab.2. In the New Firmware File eld, click Browse to locate the downloaded le.3. Click Upload. NOTES: • Whentheupgradeprocessiscomplete,waitforsometimeforthesystem to reboot. • Iftheupgradeprocessfails,thewirelessrouterautomaticallyentersrescue mode and the power LED indicator on the front panel starts ashing slowly. To recover or restore the system, refer to section 5.2 Firmware Restoration. 4.7.4 Restore/Save/Upload SettingTo restore/save/upload wireless router settings:1. From the navigation panel, go to Advanced Settings > Administration > Restore/Save/Upload Setting tab.2. Select the tasks that you want to do:• Torestoretothedefaultfactorysettings,clickRestore, and click OK in the conrmation message.• Tosavethecurrentsystemsettings,clickSave, navigate to the folder where you intend to save the le and click Save.• Torestorefromasavedsystemsettingsle,clickBrowse to locate your le, then click Upload.If issues occur, upload the latest rmware version and congure new settings. Do not restore the router to its default settings.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-9.png)
![804.8 System LogSystem Log contains your recorded network activities.NOTE: System log resets when the router is rebooted or powered o.To view your system log:1. From the navigation panel, go to Advanced Settings > System Log.2. You can view your network activities in any of these tabs:• GeneralLog• DHCPLeases• WirelessLog• PortForwarding• RoutingTable](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-10.png)
![815 UtilitiesNOTES: • Installthewirelessrouter'sutilitiesfromthebundledsupportCD.• IfAutorunisdisabled,runsetup.exe from the root directory of the support CD.• TheutilitiesarenotsupportedonMACOS.5.1 Device DiscoveryDevice Discovery is an ASUS WLAN utility that detects an ASUS wireless router device, and allows you to congure the wireless networking settings.To launch the Device Discovery utility:• Fromyourcomputer’sdesktop,click Start > All Programs > ASUS Utility > RT-AC66U B1 Wireless Router > Device Discovery.RT-AC66U B1 ASUS 192.168.1.1 255.255.255.0B1NOTE: When you set the router to Access Point mode, you need to use Device Discovery to get the router’s IP address.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-11.png)
![825.2 Firmware RestorationFirmware Restoration is used on an ASUS Wireless Router that failed during its rmware upgrading process. It uploads the rmware that you specify. The process takes about three to four minutes.IMPORTANT: Launch the rescue mode on the router before using the Firmware Restoration utility.NOTE: This feature is not supported on MAC OS.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-12.png)
![835.3 Setting up your printer server5.3.1 ASUS EZ Printer SharingASUS EZ Printing Sharing utility allows you to connect a USB printer to your wireless router’s USB port and set up the print server. This allows your network clients to print and scan les wirelessly.NOTE: The print server function is supported on Windows® XP, Windows® Vista, and Windows® 7.To set up the EZ Printer sharing mode:1. From the navigation panel, go to General > USB Application > Network Printer Server. 2. Click Download Now! to download the network printer utility.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-13.png)
![84NOTE: Network printer utility is supported on Windows® XP, Windows® Vista, and Windows® 7 only. To install the utility on Mac OS, select Use LPR protocol for sharing printer.3. Unzip the downloaded le and click the Printer icon to run the network printer setup program.4. Follow the onscreen instructions to set up your hardware, then click Next.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-14.png)
![855. Wait a few minutes for the initial setup to nish. Click Next.6. Click Finish to complete the installation. RT-AC66U B17. Follow the Windows® OS instructions to install the printer driver.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-15.png)
![868. After the printer’s driver installation is complete, network clients can now use the printer.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-16.png)
![875.3.2 Using LPR to Share PrinterYou can share your printer with computers running on Windows® and MAC operating system using LPR/LPD (Line Printer Remote/Line Printer Daemon).Sharing your LPR printerTo share your LPR printer:1. From the Windows® desktop, click Start > Devices and Printers > Add a printer to run the Add Printer Wizard.2. Select Add a local printer and then click Next.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-17.png)
![883. Select Create a new port then set Type of Port to Standard TCP/IP Port. Click New Port.4. In the Hostname or IP address eld, key in the IP address of the wireless router then click Next.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-18.png)
![895. Select Custom then click Settings.6. Set Protocol to LPR. In the Queue Name eld, key in LPRServer then click OK to continue.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-19.png)
![907. Click Next to nish setting up the standard TCP/IP port.8. Install the printer driver from the vendor-model list. If your printer is not in the list, click Have Disk to manually install the printer drivers from a CD-ROM or le.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-20.png)
![919. Click Next to accept the default name for the printer.10. Click Finish to complete the installation.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-21.png)
![92 5.4 Download MasterDownload Master is a utility that helps you download les even while your laptops or other devices are switched o.NOTE: You need a USB device connected to the wireless router to use Download Master.To use Download Master:1. Click General > USB application > Download Master to download and install the utility automatically. NOTE: If you have more than one USB drive, select the USB device you want to download the les to.2. After the download process is nished, click the Download Master icon to start using the utility.3. Click Add to add a download task.4. Select a download type such as BitTorrent, HTTP, or FTP. Provide a torrent le or a URL to begin downloading.NOTE: For details on Bit Torrent, refer to section 5.4.1 Conguring the Bit Torrent download settings.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-22.png)
![935. Use the navigation panel to congure the advanced settings.To congure BitTorrent download settings:1. From Download Master’s navigation panel, click Bit Torrent to launch the Bit Torrent Setting page.2. Select a specic port for your download task.3. To prevent network congestion, you can limit the maximum upload and download speeds under Speed Limits.4. You can limit the maximum number of allowed peers and enable or disable le encryption during downloads.5.4.1 Conguring Bit Torrent download settings](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-23.png)
![945.4.2 NZB settingsYou can set up a USENET server to download NZB les. After entering USENET settings, Apply.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-24.png)
![956 TroubleshootingThis chapter provides solutions for issues you may encounter with your router. If you encounter problems that are not mentioned in this chapter, visit the ASUS support site at: http://support.asus.com/ for more product information and contact details of ASUS Technical Support.6.1 Basic TroubleshootingIf you are having problems with your router, try these basic steps in this section before looking for further solutions.Upgrade Firmware to the latest version.1. Launch the Web GUI. Go to Advanced Settings > Administration > Firmware Upgrade tab. Click Check to verify if the latest rmware is available. 2. If the latest rmware is available, visit the ASUS global website at http://www.asus.com/Networks/Wireless_Routers/RTAC66U/#download to download the latest rmware. 3. From the Firmware Upgrade page, click Browse to locate the rmware le. 4. Click Upload to upgrade the rmware.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-25.png)
![96Restart your network in the following sequence:1. Turn o the modem.2. Unplug the modem.3. Turn o the router and computers.4. Plug in the modem.5. Turn on the modem and then wait for 2 minutes.6. Turn on the router and then wait for 2 minutes.7. Turn on computers.Check if your Ethernet cables are plugged properly.• WhentheEthernetcableconnectingtherouterwiththemodem is plugged in properly, the WAN LED will be on. • WhentheEthernetcableconnectingyourpowered-on computer with the router is plugged in properly, the corresponding LAN LED will be on. Check if the wireless setting on your computer matches that of your computer.• Whenyouconnectyourcomputertotherouterwirelessly,ensure that the SSID (wireless network name), encryption mehtod, and password are correct.Check if your network settings are correct. • EachclientonthenetworkshouldhaveavalidIPaddress.ASUSrecommends that you use the wireless router’s DHCP server to assign IP addresses to computers on your network.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-26.png)
![97• Somecablemodemserviceprovidersrequireyoutousethe MAC address of the computer initially registered on the account. You can view the MAC address in the web GUI, Network Map > Clients page, and hover the mouse pointer over your device in Client Status.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-27.png)
![986.2 Frequently Asked Questions (FAQs) I cannot access the router GUI using a web browser• Ifyourcomputeriswired,checktheEthernetcableconnectionand LED status as described in the previous section.• Ensurethatyouareusingthecorrectlogininformation.Thedefault factory login name and password is “admin/admin”. Ensure that the Caps Lock key is disabled when you enter the login information.• Deletethecookiesandlesinyourwebbrowser.ForInternetExplorer 8, follow these steps: 1. Launch Internet Explorer 8, then click Tools > Internet Options. 2. In the General tab, under Browsing history, click Delete…, select Temporary Internet Files and Cookies then click Delete. NOTES: • Thecommandsfordeletingcookiesandlesvarywithwebbrowsers.• Disableproxyserversettings,cancelthedial-upconnection,and set the TCP/IP settings to obtain IP addresses automatically. For more details, refer to Chapter 1 of this user manual.• EnsurethatyouuseCAT5eorCAT6ethernetcables.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-28.png)
![99The client cannot establish a wireless connection with the router.NOTE: If you are having issues connecting to 5Ghz network, make sure that your wireless device supports 5Ghz or features dual band capabilities.• OutofRange: • Movetherouterclosertothewirelessclient. • Trytoadjustantennasoftheroutertothebestdirectionasdescribed in section 1.4 Positioning your router. • DHCPserverhasbeendisabled: 1. Launch the web GUI. Go to General > Network Map> Clients and search for the device that you want to connect to the router. 2. If you cannot nd the device in the Network Map, go to Advanced Settings > LAN > DHCP Server, Basic Cong list, select Ye s on the Enable the DHCP Server.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-29.png)
![100• SSIDhasbeenhidden.IfyourdevicecanndSSIDsfromotherrouters but cannot nd your router’s SSID, go to Advanced Settings > Wireless > General, select No on Hide SSID, and select Auto on Control Channel. • IfyouareusingawirelessLANadapter,checkifthewirelesschannel in use conforms to the channels available in your country/area. If not, adjust the channel, channel bandwidth, and wireless mode.• Ifyoustillcannotconnecttotherouterwirelessly,youcanresetyour router to factory default settings. In the router GUI,click Administration > Restore/Save/Upload Setting and click Restore.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-30.png)
![101Internet is not accessible.• CheckifyourroutercanconnecttoyourISP’sWANIPaddress.To do this, launch the web GUI and go to General> Network Map, and check the Internet Status. • IfyourroutercannotconnecttoyourISP’sWANIPaddress,try restarting your network as described in the section Restart your network in following sequence under Basic Troubleshooting. • ThedevicehasbeenblockedviatheParentalControlfunction.Go to General > Parental Control and see if the device is in the list. If the device is listed under Client Name, remove the device using the Delete button or adjust the Time Management Settings.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-31.png)
![102• IfthereisstillnoInternetaccess,trytorebootyourcomputerand verify the network’s IP address and gateway address. • CheckthestatusindicatorsontheADSLmodemandthewireless router. If the WAN LED on the wireless router is not ON, check if all cables are plugged properly.You forgot the SSID (network name) or network password• SetupanewSSIDandencryptionkeyviaawiredconnection(Ethernet cable). Launch the web GUI, go to Network Map, click the router icon, enter a new SSID and encryption key, and then click Apply. • Resetyourroutertothedefaultsettings.LaunchthewebGUI,go to Administration > Restore/Save/Upload Setting, and click Restore. The default login account and password are both “admin”. How to restore the system to its default settings?• GotoAdministration > Restore/Save/Upload Setting, and click Restore. The following are the factory default settings: User Name: admin Password: admin IP address: router.asus.com SSID (2.4GHz): Refer to the label at the bottom of the router SSID (5GHz): Refer to the label at the bottom of the routerFirmware upgrade failed. Launch the rescue mode and run the Firmware Restoration utility. Refer to section 5.2 Firmware Restoration on how to use the Firmware Restoration utility.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-32.png)
![103Cannot access Web GUIA. Disable the proxy server, if enabled.Windows® 71. Click Start > Internet Explorer to launch the browser.2. Click Tools > Internet options > Connections tab > LAN settings.Before conguring your wireless router, do the steps described in this section for your host computer and network clients.3. From the Local Area Network (LAN) Settings screen, untick Use a proxy server for your LAN.4. Click OK when done.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-33.png)
![104MAC OS1. From your Safari browser, click Safari > Preferences > Advanced > Change Settings...2. From the Network screen, deselect FTP Proxy and Web Proxy (HTTP).3. Cllick Apply Now when done.NOTE: Refer to your browser's help feature for details on disabling the proxy server.B. Set the TCP/IP settings to automatically obtain an IP address.Windows® 71. Click Start > Control Panel > Network and Internet > Network and Sharing Center > Manage network connections.2. Select Internet Protocol Version 4 (TCP/IPv4) or Internet Protocol Version 6 (TCP/IPv6), then click Properties.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-34.png)
![1053. To obtain the IPv4 IP settings automatically, tick Obtain an IP address automatically. To obtain the IPv6 IP settings automatically, tick Obtain an IPv6 address automatically. 4. Click OK when done.MAC OS1. Click the Apple icon located on the top left of your screen.2. Click System Preferences > Network > Congure...3. From the TCP/IP tab, select Using DHCP in the Congure IPv4 dropdown list.4. Cllick Apply Now when done.NOTE: Refer to your operating system’s help and support feature for details on conguring your computer’s TCP/IP settings.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-35.png)
![106C. Disable the dial-up connection, if enabled.Windows® 71. Click Start > Internet Explorer to launch the browser.2. Click Tools > Internet options > Connections tab.3. Tick Never dial a connection.4. Click OK when done.NOTE: Refer to your browser's help feature for details on disabling the dial-up connection.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-36.png)
![107AppendicesNoticesASUS Recycling/Takeback ServicesASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling information in dierent regions.REACHComplying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website athttp://csr.asus.com/english/index.aspxFederal Communications Commission StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • Thisdevicemaynotcauseharmfulinterference.• Thisdevicemustacceptanyinterferencereceived,includinginterference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-37.png)
![108Prohibition of Co-locationThis device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitterCAUTION: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.IMPORTANT! This device is restricted for indoor use.against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorientorrelocatethereceivingantenna.• Increasetheseparationbetweentheequipmentandreceiver.• Connecttheequipmentintoanoutletonacircuitdierentfrom that to which the receiver is connected.• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-38.png)
![109Safety InformationTo maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 25cm between the radiator and your body. Use on the supplied antenna.Declaration of Conformity for R&TTE directive 1999/5/ECEssential requirements – Article 3Protection requirements for health and safety – Article 3.1aTesting for electric safety according to EN 60950-1 has been conducted. These are considered relevant and sucient.Protection requirements for electromagnetic compatibility – Article 3.1bTesting for electromagnetic compatibility according to EN 301 489-1 and EN 301 489-17 has been conducted. These are considered relevant and sucient.Eective use of the radio spectrum – Article 3.2Testing for radio test suites according to EN 300 328 & EN 301 893 have been conducted. These are considered relevant and sucient.Operate the device in 5150-5250 MHz frequency band for indoor use only. CE Mark WarningThis is a Class B product, in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-39.png)
![110Canada, Industry Canada (IC) NoticesThis device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Radio Frequency (RF) Exposure InformationThe radiated output power of the ASUS Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.This device has been evaluated for and shown compliant with the IC Specic Absorption Rate (“SAR”) limits when installed in specic host products operated in portable exposure conditions (antennas are less than 25 centimeters of a person’s body).This device has been certied for use in Canada. Status of the listing in the Industry Canada’s REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=engAdditional Canadian information on RF exposure also can be found at the following web: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.htmlCanada, avis d’Industry Canada (IC)Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-40.png)
![111doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.FCC Statement:For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.IC Statement:For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d’autres canaux n’est pas possible.This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures.Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur.The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur an de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-41.png)
![112The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specied for point-to-point and non-point-to-point operation as appropriate.le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz)doit se conformer à la limite de p.i.r.e. spéciée pour l’exploitation point à point et non point à point, selon le cas.IC Radiation Exposure Statement:This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 25 cm de distance entre la source de rayonnement et votre corps.This radio transmitter (IC: 3568A-RTACHC00) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 3568A-RTACHC00) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-42.png)
![113au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.Antenna list:Ant. Brand P/NO AntennaType Connector 2.4G Gain (dBi)5G Gain (dBi)1 Walsin RFDPA181312IMLB701 Dipole I-PEX 1.85 3.142 Walsin RFDPA181306IMLB701 Dipole I-PEX 1.83 2.73 Walsin RFDPA181305IMLB701 Dipole I-PEX 2.22 3.28Note: The EUT has three antennas.Japan Statement:5GHz band (W52, W53): Indoor use onlyNCC 警語經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。GNU General Public LicenseLicensing informationThis product includes copyrighted third-party software licensed under the terms of the GNU General Public License. Please see The GNU General Public License for the exact terms and conditions of this license. We include a copy of the GPL with every CD shipped with our product. All future rmware updates will also be accompanied with their respective source code. Please visit our](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-43.png)
![114web site for updated information. Note that we do not oer direct support for the distribution.GNU GENERAL PUBLIC LICENSEVersion 2, June 1991Copyright (C) 1989, 1991 Free Software Foundation, Inc.59 Temple Place, Suite 330, Boston, MA 02111-1307 USAEveryone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.PreambleThe licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-44.png)
![115you if you distribute copies of the software, or if you modify it.For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.We protect your rights with two steps: (1) copyright the software, and (2) oer you this license which gives you legal permission to copy, distribute and/or modify the software.Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modied by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reect on the original authors’ reputations.Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in eect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.The precise terms and conditions for copying, distribution and modication follow.Terms & conditions for copying, distribution, & modication0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-45.png)
![116The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modication”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modication are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option oer warranty protection in exchange for a fee.2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modied les to carry prominent notices stating that you changed the les and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-46.png)
![117third parties under the terms of this License. c) If the modied program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modied work as a whole. If identiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-47.png)
![118readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written oer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the oer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an oer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface denition les, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by oering access to copy from a designated place, then oering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-48.png)
![119their licenses terminated so long as such parties remain in full compliance.5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-49.png)
![120apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may dier in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program species a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-50.png)
![12110. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are dierent, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-51.png)
![122NO WARRANTY11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.END OF TERMS AND CONDITIONS](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-52.png)
![123For Turkey onlyAEEE Yönetmeliğine Uygundur.Authorised distributors in Turkey:BOGAZICI BIL GISAYAR SAN. VE TIC. A.S.Tel. No.: +90 212 3311000Address: AYAZAGA MAH. KEMERBURGAZ CAD. NO.10 AYAZAGA/ISTANBULCIZGI Elektronik San. Tic. Ltd. Sti.Tel. No.: +90 212 3567070Address: CEMAL SURURI CD. HALIM MERIC IS MERKEZI No: 15/C D:5-6 34394 MECIDIYEKOY/ISTANBULKOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.Tel. No.: +90 216 5288888Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-53.png)
![124ASUS Contact informationASUSTeK COMPUTER INC. (Asia Pacic)Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259Website www.asus.com.twTechnical SupportTelephone +886228943447Support Fax +886228907698Online support support.asus.comASUS COMPUTER INTERNATIONAL (America)Address 800 Corporate Way, Fremont, CA 94539, USATelephone +15107393777Fax +15106084555Website usa.asus.comOnline support support.asus.comASUS COMPUTER GmbH (Germany and Austria)Address Harkort Str. 21-23, D-40880 Ratingen, GermanySupport Fax +49-2102-959931Website asus.com/deOnline contact eu-rma.asus.com/salesTechnical SupportTelephone (Component) +49-2102-5789555Telephone Germany (System/Notebook/Eee/LCD) +49-2102-5789557Telephone Austria (System/Notebook/Eee/LCD) +43-820-240513Support Fax +49-2102-959911Online support support.asus.com](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-54.png)
![125Networks Global Hotline InformationRegion Country Hotline Number Service HoursEuropeCyprus 800-92491 09:00-13:00 ; 14:00-18:00 Mon-FriFrance 0033-170949400 09:00-18:00 Mon-FriGermany0049-180501092009:00-18:00 Mon-Fri10:00-17:00 Mon-Fri0049-1805010923(component support)0049-2102959911 ( Fax )Hungary 0036-15054561 09:00-17:30 Mon-FriItaly 199-400089 09:00-13:00 ; 14:00-18:00 Mon-FriGreece 00800-44142044 09:00-13:00 ; 14:00-18:00 Mon-FriAustria 0043-820240513 09:00-18:00 Mon-FriNetherlands/Luxembourg 0031-591570290 09:00-17:00 Mon-FriBelgium 0032-78150231 09:00-17:00 Mon-FriNorway 0047-2316-2682 09:00-18:00 Mon-FriSweden 0046-858769407 09:00-18:00 Mon-FriFinland 00358-969379690 10:00-19:00 Mon-FriDenmark 0045-38322943 09:00-18:00 Mon-FriPoland 0048-225718040 08:30-17:30 Mon-FriSpain 0034-902889688 09:00-18:00 Mon-FriPortugal 00351-707500310 09:00-18:00 Mon-FriSlovak Republic 00421-232162621 08:00-17:00 Mon-FriCzech Republic 00420-596766888 08:00-17:00 Mon-FriSwitzerland-German 0041-848111010 09:00-18:00 Mon-FriSwitzerland-French 0041-848111014 09:00-18:00 Mon-FriSwitzerland-Italian 0041-848111012 09:00-18:00 Mon-FriUnited Kingdom 0044-1442265548 09:00-17:00 Mon-FriIreland 0035-31890719918 09:00-17:00 Mon-FriRussia and CIS 008-800-100-ASUS 09:00-18:00 Mon-FriUkraine 0038-0445457727 09:00-18:00 Mon-Fri](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-55.png)
![126Networks Global Hotline InformationRegion Country Hotline Numbers Service HoursAsia-PacicAustralia 1300-278788 09:00-18:00 Mon-FriNew Zealand 0800-278788 09:00-18:00 Mon-FriJapan 0800-1232787 09:00-18:00 Mon-Fri09:00-17:00 Sat-Sun0081-570783886(Non-Toll Free )09:00-18:00 Mon-Fri09:00-17:00 Sat-SunKorea 0082-215666868 09:30-17:00 Mon-FriThailand 0066-24011717 09:00-18:00 Mon-Fri1800-8525201Singapore 0065-64157917 11:00-19:00 Mon-Fri0065-67203835 11:00-19:00 Mon-Fri( Repair Status Only ) 11:00-13:00 SatMalaysia 0060-320535077 10:00-19:00 Mon-FriPhilippine 1800-18550163 09:00-18:00 Mon-FriIndia 1800-2090365 09:00-18:00 Mon-SatIndia(WL/NW) 09:00-21:00 Mon-SunIndonesia 0062-2129495000 09:30-17:00 Mon-Fri500128 (Local Only) 9:30 – 12:00 SatVietnam 1900-555581 08:00-12:00 13:30-17:30 Mon-SatHong Kong 00852-35824770 10:00-19:00 Mon-SatAmericasUSA 1-812-282-2787 8:30-12:00 EST Mon-FriCanada 9:00-18:00 EST Sat-SunMexico 001-8008367847 08:00-20:00 CST Mon-Fri08:00-15:00 CST Sat](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-56.png)
![127NOTE: For more information, visit the ASUS support site at: http://support.asus.comManufacturer: ASUSTeK Computer Inc.Tel: +886-2-2894-3447Address: 4F, No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWANAuthorised representative in Europe:ASUS Computer GmbHAddress: HARKORT STR. 21-23, 40880 RATINGEN, GERMANYRegion Country Hotline Numbers Service HoursMiddle East + AfricaEgypt 800-2787349 09:00-18:00 Sun-ThuSaudi Arabia 800-1212787 09:00-18:00 Sat-WedUAE 00971-42958941 09:00-18:00 Sun-ThuTurkey 0090-2165243000 09:00-18:00 Mon-FriSouth Africa 0861-278772 08:00-17:00 Mon-FriIsrael *6557/00972-39142800 08:00-17:00 Sun-Thu*9770/00972-35598555 08:30-17:30 Sun-ThuBalkan CountriesRomania 0040-213301786 09:00-18:30 Mon-FriBosnia Herzegovina 00387-33773163 09:00-17:00 Mon-FriBulgaria 00359-70014411 09:30-18:30 Mon-Fri00359-29889170 09:30-18:00 Mon-FriCroatia 00385-16401111 09:00-17:00 Mon-FriMontenegro 00382-20608251 09:00-17:00 Mon-FriSerbia 00381-112070677 09:00-17:00 Mon-FriSlovenia 00368-59045400 08:00-16:00 Mon-Fri00368-59045401Estonia 00372-6671796 09:00-18:00 Mon-FriLatvia 00371-67408838 09:00-18:00 Mon-FriLithuania-Kaunas 00370-37329000 09:00-18:00 Mon-FriLithuania-Vilnius 00370-522101160 09:00-18:00 Mon-FriNetworks Global Hotline Information](https://usermanual.wiki/ASUSTeK-Computer/RTACHC00.Users-Manual-Part-2/User-Guide-3083281-Page-57.png)