ASSALOY SCYICLS2 Microprocessor Controlled Networked Locks User Manual XX XXXX Exhibit Cover

ASSA ABLOY Inc. Microprocessor Controlled Networked Locks XX XXXX Exhibit Cover

UserManual.wiki >

SCYICLS2 User Manual >

Contents

P2 Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: U4A-SCYICLS2 IC: 6982A-SCYICLS2 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 11-0071.W06.11.A Manufacturer: Assa Abloy, Inc. Model: P2-IM/IKM Manual

A8011E12/10Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. PASSPORT 1000Mortise LockInstallation InstructionsP2PRELIMINARY

1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/10/10Warning 1!To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only. 1234567 Table of ContentsWarning ...................................................................................2General Description .................................................................3Hardware Speciﬁcations .........................................................3Electronic Speciﬁcations .........................................................3Parts Breakdown .....................................................................4Installation Instructions ..........................................................7Operational Check ................................................................14Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCCNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.Industry Canada: Statement: The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical speciﬁcations were met.This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.PRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8011E 3Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P2 Mortise Lock General Description2Hardware Specifications3Electronic Specifications4• Complete lockset with on-board memory• Magnetic swipe standard with optional 125 kHz Proximity Reader (specify PRX-), 13.56 MHz reader (specify IKM-), and/or keypad (specify KP-)• ADA compliant• Easily retroﬁts existing Passport 1000 door preps (mortise)• Latch - Stainless steel• Optional deadbolt - Stainless steel• Guardbolt - Stainless steel, non handed• Handing (RH/RHR/LH/LHR) must be speciﬁed, but is easily ﬁeld-reversible without opening the lock case• Wireless (WiFi 802.11 b/g) online, battery-operated• 2,400 users per lock; 10,000 event audit trail• Multiple time zone and holiday access scheduling• First-In unlock conﬁguration, either by time or by user (selectable)• Input Power: DC 9V, 1.5A (6 AA alkaline batteries or optional hard-powered)• Uses existing Magstripe keycards (track 2)• Magnetic Stripe Card Coercivity: HiCo (4000 Oersted) or LoCo (300 Oersted)• Supports HID 125 kHz prox or 13.56 MHz iCLASS credentials (26 - 39 bit); supports CSN reads for other common 13.56 MHz cards, including Mi-Fare, DesFire, and FeliCa• AWE Preﬁx Available for WPA2, PEAP and EAP-TLS Wireless Encryption Support• Case - 12 gauge heavy duty wrought steel• Outside lever is unlocked through access control credentials only • Cylinder retracts latchbolt (and deadbolt)• Inside lever retracts latch and deadbolt simultan ously• Lock furnished for 1-3/4” doors. For other thicknesses, Consult factory.• UL Listed (3 hr.)• Outside lever controlled by any combination of keypad, magnetic swipe, iCLASS, prox (proximity) reader, or me-chanical cylinder • Outside lever for iCLASS controlled by HID iCLASS credential or other 13.56 MHz credential (such as CSN, Chip Serial Number, read only supported, including MiFare, DesFire, and Felica)The SARGENT Passport Series v.P2 Mortise Lock is available with either an HID® Prox 125 kHz or 13.56 MHz iCLASS® technology reader. Designed speciﬁcally for the campus market, the SARGENT Passport 1000 P2 WiFi Mortise Lock is a new breed of electronic lock, providing access control with magnetic swipe and optional Proximity Reader and/or Keypad, as well as detailed audit capabilities.• Using WiFi technology and coupled with third party software, the P2 Mortise lock offers a complete, integrated access control system.• The Passport 1000 P2 operates on six (6) “AA” alkaline batteries and may be used for both indoor and outdoor applications. Note: A weather-protective gasket is recommended for outdoor applications.HID and iCLASS are registered trademarks of HID Global Corporation.PRELIMINARY

4 1-800-810-WIRE • www.sargentlock.com • A8011E Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P2 Mortise Lock Parts Breakdown5P2 WiFi Lock with Magnetic Card Swipe With or Without Keypad91012131012467P2355Inside1011Outside58Inside 91012131012467P2355Inside1011Outside5891110121314Outside ITEM No. PART No. DESCRIPTION1 52-0757 Lens (Cliplite)252-0738 Outside Passport Escutcheon Only (Magnetic Swipe and Keypad)52-0739 Outside Passport Escutcheon Only (Magnetic Swipe)3 52-0760 Light Pipe (Cliplite)4 52-3594 Slim Style Keypad Assembly5 01-9299 #4-40 x 3/16” Phillips Pan Head Screw6 52-4243 Swipe Reader Assembly7 52-0745 Online Interface PCB8 52-3209 Harness Assembly9 52-0748 Inside Mounting Plate10 77-0168 #8-32 x 1-7/8” Phillips Flat Head Screw11 01-1146 #8-32 x 3/8” Phillips Flat Head Screw01-1176 #8 x 3/8” Phillips Flat Head Wood Screw12 52-4246 Modular Component13 52-3592 Inside Escutcheon Assembly14 01-4421 #8-32 x 1/2” T-20 Torx Pan Head ScrewPRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8011E 5Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P2 Mortise Lock Parts Breakdown (Continued)ITEM No. PART No. DESCRIPTION1 52-1103 Outside Passport Escutcheon only (Magnetic Swipe, Keypad and Proximity Reader)2 52-3593 Slim Style Keypad Assembly3 01-9299 #4-40 x 3/16” Phillips Pan Head Screw4 52-4243 Swipe Reader Assembly5 52-1106 Prox Reader Gasket6 52-4206 Antenna Assembly7 52-0745 Online Interface PCB8 52-3209 Harness Assembly9 52-1109 Back Plate10 52-0748 Inside Mounting Plate11 77-0168 #8-32 x 1-7/8” Phillips Flat Head Screw12 01-1146 #8-32 x 3/8” Phillips Flat Head Screw01-1176 #8 x 3/8” Phillips Flat Head Wood Screw13 52-0751 Battery Cartridge (Only)14 52-4263 AWE Controller Assembly Kit52-4247 Modular Component and Battery Cartridge Kit15 52-3592 Inside Escutcheon Assembly16 01-4421 #8-32 x 1/2” T-20 Torx Pan Head Screw91012131012467P2355Inside1011Outside5812343795638510121113 141516Inside Outside P2 WiFi Lock with Magnetic Card Swipe, 125 kHz and Keypad PRELIMINARY

6 1-800-810-WIRE • www.sargentlock.com • A8011E Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P2 Mortise Lock P2 WiFi Lock with Magnetic Card Swipe, 13.56 MHz and Keypad ITEM No. PART No. DESCRIPTION1 52-4402 Outside Mask Assembly 2 52-1255 Outside Escutcheon - iCLASS3 52-3593 Slim Style Keypad Assembly4 01-9299 #4-40 x 3/16” Machine Screw5 52-4243 Swipe Reader Assembly6 52-4401 iCLASS Module Assembly 7 52-3209 Harness Assembly8 52-4410 iCLASS Harness9 52-1109 Back Plate10 01-9300 #4-32 x 5/16” Plastite Screw123451044498764Parts Breakdown (Continued)PRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8011E 7Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P2 Mortise Lock ITEM PART No. DESCRIPTION1 See catalog #41 Cylinder (1-1/8” Minimum Length)2 13-0140 Cylinder Compression Spring3 See catalog 1KB-1 Cylinder Rosette4 See catalog Mortise Lockbody5 77-2592 130 KB Thumbturn for Deadbolt Functions Only6 See catalog Inside Lever Handle7 See catalog Outside Lever Assembly8 82-0368 Spindle9 82-3088 Inside Lever/Knob Adapter Plate Assembly10 01-1495 #8-32 X 5/8 Machine Screw11 82-0612 Non Loosening Wave Washer12 See catalog Mortise Rose13 82-0347 Spindle Spring14 01-1019 #12-24 X 1/2” Machine Screw15 01-2299 12 X 1-1/4 Wood Screw16 82-0578 Outside Front Plate (Electrical, Latchbolt & Guardbolt)82-0579 Outside Front Plate (Electrical, Deadbolt, Latchbolt and Guardbolt)17 01-1028 #8-32 X 1/4 Machine Screw56789101112131415 16 17438200 Series Mortise LockParts Breakdown (Continued)PRELIMINARY

8 1-800-810-WIRE • www.sargentlock.com • A8011E Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P2 Mortise Lock 1 Door PreparationInstallation Instructions6A. Verify Hand and Bevel of DoorLeft HandHinges Left.Open Inward.“LH”Left HandReverse BevelHinges Left.Open Outward.“LHRB”Right HandHinges Right.Open Inward.“RH”Right HandReverse BevelHinges Right.Open Outward.“RHRB”Stand on outside of locked door when determining door hand.Refer to template A7950 for wood and metal doors.• (IKM-) (KP-) P2- (PRX-) 82276 x Rose & Lever x Finish x Hand• (IKM-) (KP-) P2- (PRX-) 82277 x Rose & Lever x Finish x Hand• (IKM-) (KP-) P2- (PRX-) 82278 x Rose & Lever x Finish x Hand• (IKM-) (KP-) P2- (PRX-) 82279 x Rose & Lever x Finish x Hand Note: KP- is for the optional Keypad and PRX- is for the optional Proximity ReaderOutside of Door Inside of DoorThrough Bolt HolesInside Mounting Plate Mounting HolesController CutoutThumb Turn Location(Deadbolt Functions Only)Lever Handle HolesThrough Bolt HolesController CutoutCylinder HoleLever Handle HolesMortise Pocket(8200)Raceway for PowerRaceway for PowerB. Verify Product LabelC. Door PreparationRed surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):1. Position lock body with red surface of locking piece visible.2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.3. Rotate the locking piece 180° until RED surface is on opposite side.Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody.Make sure the plastic retaining ring is seated cor-rectly (Fig. 2B):1. The wires and the plastic retaining ring must be located on the non-cylinder side. 2. Orient the plastic retaining ring so that the word Bottom is located at the bottom of the cylinder hole.3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring. Beveled surface of latchbolt must face strike. The deadlatch is self adjusting. To change the hand of the latchbolt:1. Insert the blade of a slotted screwdriver (>1/4”) into the spade shape slot behind latch.2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front.3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody.Note: Latch cannot be unscrewed.PRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8011E 9Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P2 Mortise Lock Refer to template A7950 for wood and metal doors.2 How to Change Hand of LockbodyA. Reverse Lock HandRed surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):1. Position lock body with red surface of locking piece visible.2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.3. Rotate the locking piece 180° until RED surface is on opposite side.Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody.Inside of DoorPlastic Retaining RingConnectorRing TerminalSlotB. Retaining RingMake sure the plastic retaining ring is seated cor-rectly (Fig. 2B):1. The wires and the plastic retaining ring must be located on the non-cylinder side. 2. Orient the plastic retaining ring so that the word Bottom is located at the bottom of the cylinder hole.3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring. Locking SlideRed on locked side Push InFig. 2ARight HandLock ShownBeveled surface of latchbolt must face strike. The deadlatch is self adjusting. To change the hand of the latchbolt:1. Insert the blade of a slotted screwdriver (>1/4”) into the spade shape slot behind latch.2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front.3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody.Note: Latch cannot be unscrewed.C. Reverse Latch HandLatchboltPRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8011E 11Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P2 Mortise Lock 5 Install Inside and Outside Levers6 Deadbolt Functions Only (82276 & 82277)1. Insert alignment tool (supplied) into lock body thumb turn.2. Slide back plate over tool and make level.3. Secure back plate to door with two (2) #6 x 3/8” round head wood screws or #6-32 x 3/8” round head machine screws.4. Dispose of tool, position thumb turn over back plate (Fig. 6A) and secure with #6-32 x 1/4” ﬂat head screw.Note: Thumb turn should cover screw head when deadbolt is retracted.Refer to instructions (A5675G) included in package included with lock.1. Slide the outside lever and spindle assembly through the door and lockbody.2. Using the inside adapter plate and spindle, secure loosely with (2) #8-32 screws.Note: Position threaded hole on the inside adapter to align with lever hole.3. Tighten the lockbody screws on edge of door. 4. After the lockbody screws are tightened, tighten both inside adapter screws.5. Position and attach rose over inside adapter. 6. Position and secure inside lever to the inside adapter with set screw.Fig. 5AMortise Lock BodyConnector and Ground Ring TerminalOutside Lever AssemblyInside Adapter PlateRoseInside LeverFig. 6ABack Plate#6 x 3/8” Round Head Wood Screws#6-32 x 3/8” Round Head Machine Screws#6-32 x 1/4” Flat Head ScrewThumb TurnFig. 6B DetailAlignment ToolPRELIMINARY

12 1-800-810-WIRE • www.sargentlock.com • A8011E Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P2 Mortise Lock 7 Install Gasket (Optinal)Note: Optional, for non-ﬁre rated doors only.For non-ﬁre rated door applications, an optional gasket may be used as a weather seal between the escutcheon and the outside door surface.Peel off adhesive backing and attach to outside escutcheon.Fig. 7AOutside Passport TrimGasket8 Install Outside Escutcheon and Mounting Plate Assembly1. Insert the mounting posts through holes as shown.2. On the inside of the door, position the mounting plate over the indicated holes.Note: Feed controller and keypad cables feed through side opening (Fig. 8A).Cable and ground ring terminal from lockbody feeds from bottom (Fig. 8A and 8B).3. Attach ground ring terminal lock body to bottom right corner using one #8-32 x 1-7/8” ﬂat head machine screw. Make sure it is positioned upright (Fig. 8A).4. Insert other three #8-32 x 1-7/8” ﬂat head machine screws and tighten, fastening the outside escutcheon to the door (Fig. 8B).IMPORTANT: If the following step is skipped, the product will not be UL-compliant:5. Attach two (2) #8 x 3/8” ﬂat head wood screws for wood doors or (2) #8-32 x 3/8” ﬂat head machine screws for metal doors (Fig. 8C).(4) #8 - 32 x 1-7/8” Flat Head Machine ScrewsMounting PlateOutside Passport TrimFig. 8AAttach groundwire to bottomright screwLock CableReader/Controller Cable(2) #8 - 3/8” Flat Head Wood Screws OR(2) #8 - 3/8” Flat Head Machine ScrewsFig. 8CFig. 8BMounting PlatePosition ground ring terminal up-right, then tighten screw. Lockbody CableLock Ground Controller/ReaderCableReader Cable (iCLASS only)Reader Cable (iCLASS only)PRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8011E 13Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P2 Mortise Lock 9 Install Inside Module Component Assembly Insert bottom of Module Component Assembly ﬁrst (Fig. 9A), then clip top of Assembly to backplate, verifying both tabs attached securely.Outside of DoorFig. 9ATabs10 Attach Connectors Secure the following connectors onto the circuit board (Fig. 10A and 10B):1. Secure the 10-pin lock body assembly connector.2. Secure the 24-pin keypad/card reader connector.3. Secure 9-pin reader cable (iCLASS only). Notes: • Connectors go on only one way.• Do not force and do not offset connectors.• Be sure the connectors are completely seated (ﬂush).Fig. 10ADetail 10B24-pin fromOutside Trim10-pin fromLockbodyFig. 10B Detail9-pin Reader Cable (iCLASS Only)PRELIMINARY

14 1-800-810-WIRE • www.sargentlock.com • A8011E Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P2 Mortise Lock 11 Install Battery/Battery Pack1. Place (6) “AA” batteries into the compartment be-ing careful to align polarity (- & +) properly.2. Insert battery pack and click into place, making sure polarity terminals on the battery pack are correctly oriented (Fig. 11A). 1. Position inside escutcheon as shown (Fig. 12A).Verify that all wires are positioned within the escutcheon to avoid pinching.2. Attach escutcheon with (2) #8-32 x 1/2” T-20 Torx pan head screws.3. Straighten escutcheon and tighten securely.DO NOT OVERTIGHTEN.12 Attach Outside Front PlateFig. 11AFig. 12A(2) #8-32 x 1/2” Torx ScrewsPRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8011E 15Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P2 Mortise Lock 13 Attach Outside Front Plate Attach front plate with (2) #8-32 X 1/4” ﬂat head screws (Fig. 13A).Fig. 13A(2) #8-32 x 1/4” Flat Head ScrewsPRELIMINARY

SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.comFounded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A8011E -12/10IMPORTANT: Be sure to test functions prior to closing door.In all cases, perform the following checks:1. Ensure that inside lever retracts latch (and deadbolt for deadbolt functions).• For units with cylinders, the following checks apply:Insert key into cylinder and rotate:a. There should be no friction against lock case, wire harness, or any other obstructions. If friction or binding occurs, readjust cylinder and wiring harness to eliminate issues.b. The key should retract the latch and the key should rotate freely.c. The key should extend and retract the deadbolt.• For units without a keypad, add card using LCT software and test. • For units with a keypad, add pin and card using LCT software and test. 2. LED signalling:• After using a valid credential, a green ﬂash followed by three fast amber ﬂashes indicates a low power condition. Check the battery voltage. If the voltage is low, replace the batteries. • If the batteries die, the lock will ﬂash rapid amber for approximately one minute. After that, the lock will no longer be functional.3. When you have completed the tests, close the door, ensuring latchbolt and deadbolt fully extend into strike plate without binding.Installation Instructions7PRELIMINARY

Navigation menu