ASSALOY SCYICLS0 S-Series iClass Lock User Manual FCC Part 15

ASSA ABLOY Inc. S-Series iClass Lock FCC Part 15

UserManual.wiki >

SCYICLS0 User Manual >

Manual - S2 Series

Contents

1. Manual - S1 Series
2. Manual - S2 Series
3. Manual

Manual - S2 Series

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: U4A-SCYICLS0 IC: 6982A-SCYICLS0 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0199.W06.11.A Manufacturer: Assa Abloy, Inc. Model: S1-IA/IK, S2-IA/IK Manual Model S2-IA/IK

A7786E10/10Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Installation Instructions Proﬁle Series v.S2 WiFi Mortise Lock

1-800-810-WIRE • www.sargentlock.com • A7786ECopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Warning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Warning 11234567Table of ContentsWarning ...................................................................................2General Description .................................................................3Hardware Speciﬁcations .........................................................3Electronic Speciﬁcations .........................................................3Installation Wiring Overview ...................................................3Lock Wiring ..............................................................................4Parts Breakdown .....................................................................5Installation Instructions ..........................................................7Operational Check ................................................................1589FCC:NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.Industry Canada: Statement: The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical speciﬁ-cations were met.This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.SARGENT Mfg. Co. v.S Series locksets utilizing a door position switch (DPS) are not rated for,or intended for use in life safety applications.!

4 1-800-810-WIRE • www.sargentlock.com • A7786ECopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S2 WiFi Mortise LockLock Wiring6DX NC (GREEN/WHITE)RX COM (WHITE)RX NC (GREEN)DX (WHITE/BLACK)LX NO (RED/YELLOW)LX COM (RED/GREENMotor B (BLACK) Motor A (RED)TB1E1 TB28765432112345678From Lock Body(+) 9VDC (RED) (-) (BLACK)AX/DPS NC (PINK) AX/DPS COM (VIOLET) UnusedUnusedUnusedEGND (GREEN)DPSPowerRing Terminal From TrimController Board Connectors (Inside Escutcheon)DPS

6 1-800-810-WIRE • www.sargentlock.com • A7786ECopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S2 WiFi Mortise Lock1 Outside Lever Reference 8200 Catalog for available levers 12 Inside Lever Reference 8200 Catalog for available levers 13 82-0493 O/S Escutcheon only with Cylinder 182-0495 O/S Escutcheon only without Cylinder4 82-0492 Inside Escutcheon only without Thumb Turn 182-4571 Inside Escutcheon only with Thumb Turn 1552-2431 125 kHz Prox Only Assembly (PA)152-2432 Keypad and 125 kHz Prox Assembly (PK) OR52-4255 13.56 MHz Prox Only Assembly (IA)52-4256 Keypad and 13.56 MHz Prox Assembly (IK)6 52-4200 S2 Controller Assembly (Double Pulse) 152-4265 S2 AWE Controller Assembly Kit7 52-3855 Battery Cover Assembly 18 01-1212 Security Screw 19 52-2427 Proﬁle Screw Pack - Specify Finish (Includes: Fire Stop Plate, Trim Mounting Screws, Security Allen Wrench)110 Consult Factory Lever Handle Screw (Depends on Lever Style) 111 Consult Factory Inside Adapter Assembly (Depends on Lever Style) 112 Consult Factory Outside Adapter Assembly (Depends On Lever Style) 113 S2-82276-hand-ﬁnish Lockbody with Deadbolt with Cylinder 1S2-82277-hand-ﬁnish Lockbody with Deadbolt without CylinderS2-82278-hand-ﬁnish Lockbody without Deadbolt with CylinderS2-82279-hand-ﬁnish Lockbody without Deadbolt without Cylinder14 82-0084 Faceplate with Deadbolt (shown) 182-0081 Faceplate without deadbolt 115 77-4336 Mortise Screw Pack - Specify Finish (Includes: Wood and Me-tal Lock body Screws, Faceplate Screws, and Strike Screws)116 Consult Factory #43 Mortise Cylinder 1 ITEM PART NO. DESCRIPTION QTY.Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS, continued

8 1-800-810-WIRE • www.sargentlock.com • A7786ECopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S2 WiFi Mortise LockStep #2 – How to Change Hand of LockbodyBeveled surface of latchbolt must face strike (Fig. 2C).The deadlatch is self adjusting.To change the hand of the latchbolt:1. Insert the blade of a slotted screwdriver (>1/4") into the spade shape slot behind latch.2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front.3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody.Note: Latch cannot be unscrewed.Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):1. Position lock body with red surface of locking piece visible.2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.3. Rotate the locking piece 180° until RED surface is on opposite side.Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody. Red Locking Piece Indicates Locked SidePlastic Retaining RingOutside of DoorFig. 2BSlotConnectorPush InRight Hand ShownLocking Guide SlotFig. 2AFig. 2CA. Reverse Lock HandC. Reverse Latch HandMake sure the plastic retaining ring is seated correctly (Fig. 2B):1. The wires and the plastic retaining ring must be located on the non-cylinder side.2. Orient the plastic retaining ring so that the word Bottom is located at the bottom of the cylinder hole.3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring.B. Retaining Ring

10 1-800-810-WIRE • www.sargentlock.com • A7786ECopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S2 WiFi Mortise LockStep #5 – Install Gasket (for Exterior Doors)For exterior applications, use weather seal gasket between escutcheon and outside door surface. To apply weatherseal gasket:1. Carefully remove the backing from the gasket. (Fig. 5A).2. Apply gasket to escutcheon:a. Starting in one place, press the adhesive side of the gasket ﬁrmly against the escutcheon.b. Work around the escutcheon, pressing the sticky side of the gasket ﬁrmly against the escutcheon edge.c. The gasket should be aligned so that all edges of the escutcheon are covered.3. Attach escutcheon to the door.Note: The 43 cylinder may be used with or without a gasket.Step #6 – Install Gasket (for Exterior Doors) 1A. For fire rated doors: feed ribbon cable with connector and ground wire from outside of door through weatherseal gasket and ﬁre stop plate (Fig. 6A).Note: Install ribbon cable with cable exiting down1B. For non-fire rated doors: feed ribbon cable with connector and ground wire from outside of door through weatherseal gasket (if used) and weather conduit (Fig. 6B).Note: Install ribbon cable with cable exiting down2. With outside lever horizontal, locate the outside escutcheon on the door, while directing the mounting posts through the door and lock body (Fig. 6B).Make sure the lever spindle is properly engaged in lock.7. On the inside of the door, insert spindle into square hole of mortise lock.8. Slide inside adapter and plate assembly over spindle and loosely secure with 2 through -bolt screws (#8-32 x 5/8”). Note: For 8276 and 8278, loosely thread cylinder through escutcheon and into the lock body before tightening the lock case screws and escutcheon through bolts. Inside of DoorMortise Lock bodyand AX ConnectorsFig. 6BReader Cable Ground Wire (E1)Antenna (iCLASS)Fig. 5AKeypad RibbonCable Ground Wire (E1)GasketAntenna(iCLASS) OnlyFig. 5BAntenna (iCLASS only)Fig. 6AOutside of DoorKeypad RibbonCable Ground Wire (E1)

12 1-800-810-WIRE • www.sargentlock.com • A7786ECopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S2 WiFi Mortise Lock1. Slide lever handle onto spindle until fully seated (Fig. 10A).2. Tighten the set screw securely with 1/8" hex wrench.Step #10 – Install Inside Lever Step #9 – Install Inside Escutcheon 1. Gently fold the excess ribbon connector and ground wire into the top hole, JST connectors and ground wire into offset middle hole, and mortise and AX/DPS wires into bottom hole, being careful not to pinch wires (Fig. 9A). 2. Insert (2) #8-32 x 1-1/4" screws through inside escutcheon and thread into outside escutcheon.Straighten escutcheons and tighten securely.Inside of DoorFig. 10ASpindleSet ScrewInside LeverInside of DoorFig. 9A

14 1-800-810-WIRE • www.sargentlock.com • A7786ECopyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/15/10Profile Series v.S2 WiFi Mortise LockIMPORTANT: Do not install batteries if controller is powered by external power supply.1. To install or replace batteries, ﬁrst remove the battery cover (if necessary) using the provided security tool (Fig.13A). 2. Unscrew the bottom screw of the battery keeper and remove the battery keeper, being careful not to break the tabs at top that hold it in place (Fig.13B) 3. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.4. Replace battery keeper being careful to engage tabs at top to hold it in place (Fig. 13B).5. Attach battery cover to inside escutcheon, making sure to line up tabs with retaining slots in battery cover. 6. Secure with the security screw using tool. (Fig. 13A).Step #13 – Install (or Replace) BatteriesFig. 13BFig. 13CSecurity Allen Wrench 01-0297 includedSecurity screwBattery CoverFig. 13A

SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.comFounded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A7786E-10/10

Navigation menu