ASSALOY Hospitality AS LCU6333 RFID Reader User Manual LCU 6333

ASSA ABLOY Hospitality AS RFID Reader LCU 6333

Users Manual

Installation of LCU 6333 DRAFT
2 DRAFT 66 1502 006-0 Copyrights The information in this document is subject to change at the sole discretion of ASSA ABLOY AB without notice. Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY AB does not assume any responsibility for incidental or consequential damages arising from the use of this manual. All information and drawings in this document are the property of ASSA ABLOY AB. Unauthorized use and reproduction is prohibited. VingCard and Elsafe are registered trademarks of ASSA ABLOY AB.
3 DRAFT 66 1502 006-0 Installation of LCU 6333 LCU 6333 is used in several different VingCardElsafe products. In each case, LCU 6333 is factory mounted in the end product, so there are no special precautions the customer needs to take in terms of installing LCU 6333. Each manual for the different end products where LCU 6333 is applicable will contain the below statements for FCC and Industry Canada. FCC statements Changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The concerned end products must be labeled to say 'Contains FCC ID: Y7V –LCU 6333’. Industry Canada statements This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. l’appareil ne doit pas produire de brouillage, et 2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. If the IC Certification Number is not visible when a module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final concerned end products must be labeled in a visible area with the following: 'Contains/Contient IC: 9514A-LCU6333'
4 DRAFT 66 1502 006-0 Asia / Pacific: Europe / Middle East / Africa: E-mail: apac@vingcardelsafe.com E-mail: emea@vingcardelsafe.com Phone: +65 6305 7670 Phone: +47 69 24 50 00 Latin America: North America: E-mail: lam@vingcardelsafe.com E-mail: northamerica@vingcardelsafe.com Phone: +52 55 36 40 12 00 Phone: +1 972 907 2273 VingCard Elsafe – P.O. Box 340 – 1402 Ski – Norway – Phone: +47 69 24 50 00 info@vingcardelsafe.com | www.vingcardelsafe.com Provider of: VingCard Locks & Systems | Elsafe Safes | Orion EMS | PolarBar Minibars Specifications may change without notice

Navigation menu