ARRIS Global RNG210N Set-top Box with Moca Model:RNG210N User Manual Manual

Pace Micro Technology plc Set-top Box with Moca Model:RNG210N Manual

UserManual.wiki >

RNG210N User Manual

Manual

BRINGING TECHNOLOGY HOMEwww.pace.comUSER GUIDEPace RNG210N

2SAFETY INFORMATIONThis digital set-top has been manufactured and tested with your safety in mind. However, improper use can result in potential electric shock or ﬁre hazards. To avoid defeating the safeguards that have been built into your set-top, please observe the precautions discussed in this document.Do not perform any servicing unless you are qualiﬁed to do so. Refer all servicing to qualiﬁed service personnel. Servicing the set-top yourself will invalidate the warranty.To reduce the risk of ﬁre or electric shock, do not expose this set-top to rain or moisture.On the rear panel of your set-top there is a tamper-evident label that states ‘Warranty void if broken or removed’.To avoid possible damage to the internal hard disk, do not pick up or move your set-top while it is connected to the power supply. If you want to move your set-top, ﬁrst stop any recording, then turn off your set-top and wait 60 seconds before disconnecting it. You should handle your set-top carefully, as any damage you cause to the internal hard disk (or any other component) will invalidate your warranty.InstallationThe installation of your set-top should be carried out by a qualiﬁed installer and should conform to local codes.Note to the installerThis reminder is provided to call the attention of the cable-TV-system installer to Section 820 of the National Electrical Code (USA), which provides guidelines for proper grounding and, in particular, speciﬁes that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as is practical.To ensure correct operation, use this set-top only with the Pace-approved power supply unit provided. If you use an unapproved alternative, you will invalidate the warranty.Other warningsTo reduce the risk of electric shock, do not remove the cover of your set-top. There are no user-serviceable parts inside it.The lightning ﬂash with arrowhead symbol, within a triangle, is intended to alert you to the presence of uninsulated “dangerous” voltages within your set-top’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.The exclamation point within a triangle is intended to alert you to the presence of important instructions in the literature accompanying your set-top.Warnings on the power supplyRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION

3IMPORTANT SAFETY INSTRUCTIONSBefore you install or use the apparatus, you must read and understand these Important Safety Instructions. At all times when using the apparatus you must follow these Important Safety Instructions to reduce the risk of ﬁre, electrical shock and injury to persons.1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into the outlet, consult an electrician for replacement of the obsolete outlet.10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.11. Only use attachments/accessories speciﬁed by the manufacturer.12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. Unplug this apparatus during lightning storms or when unused for long periods of time.14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.Service address: Pace Americas Inc. 3701 FAU Boulevard, Suite 200, Boca Raton, Florida 33431 U.S.A.

4SAFETY INFORMATION (cont.)In addition to the Important Safety Instructions, please read the Safety Information below.Power sourcesThe model number, serial number, and electrical rating of this set-top are on a label on its base.You must operate your set-top only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. If you move your set-top between locations at different temperatures, allow it to reach room temperature before you apply power to it.OverloadingDo not overload wall AC outlets, extension cords or other power outlets as this can result in a risk of ﬁre or electric shock.LightningFor added protection for your set-top during a lightning storm, or when it is left unattended and unused for long periods of time, disconnect the cable system from your set-top. See also item 13 in the Important Safety Instructions.Ambient temperatureThe operating temperature range of your set-top is 32-104°F. If the ambient temperature around your set-top falls outside this range, you must correct this in order for your set-top to work correctly and safely. For example, if the temperature is too high, make sure there is sufﬁcient ventilation (see below) and that your set-top is not directly on top of or underneath other equipment.VentilationSlots and openings in the casing of your set-top are provided for ventilation, to ensure reliable operation of your set-top and to protect it from overheating.• Neverblocktheventilationopeningsbyplacingyourset-toponabed,sofa, rug, or other similar surface. Place it on a hard, ﬂat surface.• Nevercovertheventilationopeningswithitemssuchasnewspapers,table-cloths, or curtains.• Youcanplaceyourset-topnearotherconsumerelectronicsdevices,suchas stereo ampliﬁers or televisions, but you must not place it directly on top or underneath them.• Donotplaceyourset-topinabuilt-in installation such as a bookcase or rack unless proper ventilation is provided and you have adhered to the manufacturer’s instructions.• Maintain a minimum distance of three inches around your set-top for sufﬁcient ventilation.See also item 7 in the Important Safety Instructions.3 in. 3 in.3 in.

5SAFETY INFORMATION (cont.)Water and moistureDo not expose your set-top to rain or moisture, dripping or splashing, and ensure that no objects ﬁlled with liquids, such as vases, are placed on your set-top. See also item 5 in the Important Safety Instructions.Entry of objects and liquidsNever push objects of any kind into your set-top through openings as they may touch dangerous voltage points or short-out parts that could result in ﬁre or electric shock. Never spill liquid of any kind on your set-top.TransportingMove the combination of set-top and cart with care. Quick stops, excessive force and uneven surfaces may cause the combination of set-top and cart to overturn. See also item 12 in the Important Safety Instructions.Placement and mountingDo not place your set-top on an unstable or uneven surface. Your set-top may fall, causing serious injury to a child or adult and serious damage to your set-top. If you mount your set-top, for example to a wall or ceiling, follow the manufacturer’s instructions and use a mounting accessory recommended by the manufacturer. See also item 12 in the Important Safety Instructions.Risk of ﬁre or scorchingNever place naked ﬂame sources, such as lighted candles, on or adjacent to your set-top.Replacement partsWhen replacement parts are required, be sure that the service technician has used replacement parts speciﬁed by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in ﬁre, electric shock or other hazards. See also item 14 in the Important Safety Instructions.Safety checkUpon completion of any servicing or repairs to your set-top, ask the service technician to perform safety checks to determine that your set-top is in its proper operating condition. See also item 14 in the Important Safety Instructions.SAVE THIS INFORMATION FOR FUTURE REFERENCE

6SAFETY INFORMATION (cont.)Safety aspects of connectionsFull details of the rear panel are on pages 8 and 9.ConnectingDo not connect your set-top (or any other equipment such as a TV or VCR) to the power supply until you have properly connected all the other cables.Your set-top is designed for use only with the power supply unit provided.On the power supply unit there is a label that speciﬁes the correct AC power supply input for it. Do not connect the power supply unit to any supply other than this.Always connect the 15 volt DC cord from the power supply unit to your set-top before you insert the AC power cord from the power supply unit into the wall AC outlet.DisconnectingTo disconnect power from your set-top, always detach the power supply unit from the wall AC outlet (rather than remove the 15 volt cord from your set-top).Therefore you must install your set-top near to the wall AC outlet, which should be easily accessible.If you are in any doubt about the power supply cord, its plug or its connection, consult a qualiﬁed electrician.The CABLE IN connector is designed for connection to a cable network only. You must not connect any other equipment, such as a VCR, to this input.POWER INPUT15 volt power supply unitTo ensure correct operation, use this set-top only with the Pace-approved power supply unit provided. If you use an unapproved alternative, you will invalidate the warranty.

7SAFETY INFORMATION (cont.)Regulatory informationCAUTION: Do not attempt to modify your set-top without written authorization from the manufacturer. Unauthorized modiﬁcation could void your authority to operate your set-top.NOTEYour set-top has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Your set-top generates, uses and can radiate radio-frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If your set-top does cause harmful interference to radio or television reception, which can be determined by turning your set-top off and on, you are encouraged to try to correct the interference by one or more of the following measures.• Reorientorrelocatethereceivingantenna.• Increasetheseparationbetweenyourset-topandthereceiver.• Connectyourset-toptoanoutletonacircuitdifferentfromthattowhich the receiver is connected.• Consultyourdealeroranexperiencedradio/TVtechnicianforhelp.

8REAR PANELCOMPONENT VIDEO Component video output for analog HDTVAUDIO OUT Audio outputs (stereo, L and R)CABLE IN From cable service-provider1394 For connection to a 1394-compatible deviceeSATA For connection to an optional external hard disk (if enabled).POWER INPUT (Make this connection last of all)DIGITAL AUDIO Optical S/PDIF audio outputETHERNET For connection to a home network (if enabled)HDMITM Video and audio output for digital HDTV. Also an input (if enabled).USB port For connection to USB device (if enabled)CableCARD™ module (behind cover) Removal will interrupt your service

9REAR PANEL (cont.)CABLE IN Connect the cable service here. 1394 Connect to a TV with a 1394 port or to any other 1394-compatible device.COMPONENT VIDEO If your HDTV does not have an HDMI connector, connect your HDTV here.AUDIO OUT Connect to the L and R audio inputs on your stereo TV, stereo VCR, or optional stereo ampliﬁer.DIGITAL AUDIO Connect to the optical digital audio input on optional digital audio equipment, such as an audio decoder or home theater receiver.HDMI Out Connect your HDTV here for a digital audio/video connection (instead of using the component video connectors).HDMI In If this connector is enabled by your cable service-provider, you can connect another HDMI device (allowing that device’s output to loop through the set-top to the TV).CableCARD module Removal will interrupt your service. USB port If this port is enabled by your cable service-provider, you can connect compatible optional equipment that supports a USB 2.0 interface.eSATA If this connector is enabled by your cable service-provider, you can connect an optional external hard disk.ETHERNET If this connector is enabled by your cable service-provider, you can connect your set-top into an Ethernet home network.+15V POWER Connect your set-top’s power supply unit here. Make this connection last of all.

10CONNECTING THE EQUIPMENTIn order for you to view programs broadcast in high-deﬁnition, your set-top must be connected to a suitable HDTV or computer monitor. Your equipment should have been connected up by your installer. However, if you need to disconnect and reconnect your equipment, read pages 10 through 14. On pages 12 and 13, there are two typical connection setups for an HDTV, DVD player, and home theater receiver.These setups make efﬁcient use of the connectors on your set-top. However, depending on your other equipment and the connectors on it, the person who installed your system may have chosen to connect things differently.Both setups allow play-back of DVDs. You hear stereo sound from the home theater’s loudspeakers.You can take advantage of the digital audio output from your set-top by connecting a suitable cable between your home theater receiver and the DIGITAL AUDIO connector (as shown in the diagram).WARNINGSDo not connect your set-top (or any other equipment such as a TV or VCR) to the power supply until you have properly connected all the other cables.Disconnect your set-top’s power supply unit from the AC power supply before you disconnect any other equipment from its rear panel.The only way to disconnect your set-top from the AC power supply is to remove the power supply unit from the wall AC outlet (or switch the wall AC outlet switch, if present, to its OFF position). Your set-top must therefore be installed near to the wall AC outlet, The cable input is designed for connection to a cable network only. You must not connect any other equipment, such as a VCR, to this input.

11CONNECTING THE EQUIPMENT (cont.)Setup A - Home theater system with HDTV (HDMI connection)Setup A (see page 12) uses an HDMI connector to connect to the HDTV. This displays the highest quality picture on the HDTV and also means there will be no picture degradation on any copy-protected programs (provided the link remains secure – see right).Setup B - Home theater system with HDTV (Component video / YPbPr connection)Setup B (see page 13) uses a component video connection to connect to the HDTV. This displays a high deﬁnition picture on your TV.NOTEHow you set up your equipment may depend on your home theater receiver. For example, the optical audio input may be associated with a particular video input. Consult your home theater user guide for further details.NOTECopy protection via an HDMI secure linkThe HDMI link between your set-top and your HDTV should be a secure link. When your set-top is attached via an HDMI cable to an HDCP-compliant (High-bandwidth Digital Content Protection) HDTV, the HDTV and set-top negotiate a secure link, which allows your set-top to transmit full resolution video (picture) to your HDTV.Not all HDTVs support HDCP. If your set-top is connected to an HDTV that does not support it, you may see a solid-red screen or a message similar to the following:Your HDTV does not support HDCP. Please use the YPbPr component connection to watch TV.The HDMI output is then disabled, so no picture is transmitted from this connector. In that case, use the component video connectors to connect up (see Setup B).

12CONNECTING THE EQUIPMENT (cont.)DVDPB/CBPR/CRYCOMPONENT VIDEO OUTDIGITAL AUDIO OUTOPTICALCOAXIALCOMPOSITE VIDEO OUTOPTICALAUDIO INCOAXIALAUDIO INDIGITAL AUDIO INHOME THEATER RECEIVERLEFTAUDIORIGHTAUDIOVIDEOLEFTAUDIO INVCR INRIGHTAUDIO INVIDEO INANTENNA/RF INHDMIPB INPR INY INCOMPONENTVIDEO INLEFTAUDIO INRIGHTAUDIO INVIDEO INHDTVPOWERPOWERPOWERWALL AC OUTLETWALL AC OUTLETWALL ACOUTLETSCABLE INPUTSetup A: (HDMI)

13DVDPB/CBPR/CRYCOMPONENT VIDEO OUTDIGITAL AUDIO OUTOPTICALCOAXIALCOMPOSITE VIDEO OUTOPTICALAUDIO INCOAXIALAUDIO INDIGITAL AUDIO INHOME THEATER RECEIVERLEFTAUDIORIGHTAUDIOVIDEOLEFTAUDIO INVCR INRIGHTAUDIO INVIDEO INANTENNA/RF INHDMIPB INPR INY INCOMPONENTVIDEO INLEFTAUDIO INRIGHTAUDIO INVIDEO INHDTVPOWERPOWERPOWERWALL AC OUTLETWALL AC OUTLETWALL ACOUTLETSCABLE INPUTSetup B: (Component video)CONNECTING THE EQUIPMENT (cont.)

14WARNINGSDo not connect your set-top (or any other equipment such as a TV or VCR) to the AC power supply until you have properly connected all the other cables.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. Connecting the power supply unit to your set-topBefore you insert the power supply unit into the wall AC outlet, connect the 15 volt DC cord from the power supply unit to the socket labeled “+15 V 4.0 A MAX” on your set-top’s rear panel.Connecting equipment to the wall AC outletsConnect your set-top’s power supply unit, and the plugs on the power cords from your TV, DVD, and any other equipment, into wall AC outlets. If these outlets have switches, switch them ON.CONNECTING THE EQUIPMENT (cont.)

15CONNECTING THE EQUIPMENT (cont.)Lightning stormsDisconnect your set-top’s power cord during lightning storms. A lightning storm may affect your set-top, if it is on during the storm. It may appear that it has stopped working, but you can easily restore its operation as follows:Unplug your set-top’s power supply unit from the wall AC outlet. Then plug this power supply unit in again at the wall AC outlet (and, if there is a switch by this outlet, switch it to its ON position).Turning your set-top on and offAfter you have connected your set-top’s power supply unit to the wall AC outlet (and switched this outlet ON, if it has a switch), press the POWER button on your remote control to turn your set-top on (you will need to pair your remote control with your set-top ﬁrst - see page 16). The (power) light on your set-top’s front panel should light up blue, to show that your set-top is on.To turn your set-top on or off at any time, press the POWER button on your remote control.Never turn off your set-top by simply disconnecting it from the power supply. If you need to disconnect your set-top, ﬁrst stop any recording (if applicable). Then turn off your set-top by pressing the POWER button on your remote control, so that the (power) light goes off. Then wait 60 seconds before removing the power supply unit from the wall AC outlet.Power Saving: To save power and money, and to reduce greenhouse gas emissions, turn off your set-top, using the power button, when it is not in use.A blue light around the button turns on.To turn your set-top on, press the power button.Front panel display, showing the time.

16Pairing your remote control with your set-topBefore using your set-top with your TV, you must pair your remote control with your set-top. 1. Put the two AA batteries provided into your remote control.2. Turn on your TV and set-top.3. Press and hold the two buttons (the select buttons) on the front of your set-top. You’ll see a message on your TV showing you that your set-top is trying to pair with a remote control. Your TV shows you which two buttons to press on your remote control.4. Press and hold the two buttons on your remote control, as instructed on your TV screen. You’ll see a message on your TV conﬁrming that your remote control has been paired with your set-top.NOTEIf you don’t complete the process within two minutes, you’ll have to start again. Pressing EXIT on your remote control also ends the pairing process.CONNECTING THE EQUIPMENT (cont.)NOTESYour cable TV service-provider determines the digital channels, services, and screen information that you see on your TV when you use your set-top and its remote control.Consult the information supplied by your cable service-provider for details on how to make the most of the digital cable services. Also read the operating instructions that are supplied with your remote control.

17FRONT PANELPower button To turn your set-top on/off. (power) light Lights blue when your set-top is on and is not lighted when your set-top is off. Display Shows the time or the current channel number, and the setting when you make user settings.USB port (If enabled by your cable service-provider.)Select buttons To perform remote control pairing.

18THE PRODUCT TO WHICH THESE TERMS RELATE (THE “PRODUCT”) INCORPORATES SOFTWARE WHICH IS OWNED BY PACE plc (“PACE”) OR ITS THIRD PARTY LICENSORS (THE “SOFTWARE”). BEFORE USING THE PRODUCT PLEASE READ THESE TERMS. IF YOU DO NOT AGREE TO THESE TERMS YOU MAY NOT USE THE PRODUCT AND SHOULD IMMEDIATELY RETURN THE PRODUCT TO YOUR SUPPLIER. THESE TERMS ALSO APPLY TO ANY MODIFICATIONS, UPDATES OR SUPPLEMENTS TO THE SOFTWARE PROVIDED TO YOU. FOR PURPOSES OF THESE TERMS, “YOU” MEANS YOU, THE END USER, AND YOUR PRODUCT SUPPLIER, UNLESS THE CONTEXT REQUIRES OTHERWISE.A. License Grant and Conditions1. Pace, or your supplier, if applicable, grants you a non-exclusive, non-transferable, limited license to use the Software solely as integrated with, incorporated into, or provided for use in connection with the Product.2. Pace reserves all rights not expressly granted to you under these Terms.3. You may not transfer any of your limited rights in the Software without the prior written consent of Pace, and if consent is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND ONLY IF the transferee has read and agreed to accept these Terms.4. You must ensure that the copyright, trademark and other protective notices contained in the Software are maintained and not altered or removed.5. The Software is protected by copyright and other laws and international copyright and other treaties.6. The Software provided hereunder is licensed (not sold). Pace is NOT transferring title or any ownership rights in the Software to you.7. All title and intellectual property rights in and to the Software and all modiﬁcations, updates, enhancements and derivative works of the Software are owned exclusively TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”)by Pace or its licensors and you agree to execute any document reasonably requested by Pace to evidence such ownership rights.8. Certain third party software used in connection with the Product may be made directly available to you by operating system or other third party providers. Use of such Software is also subject to the terms of any applicable agreement between you and such third party.B. License RestrictionsExcept as expressly permitted herein or by statute you may not: 1. use the Software in conjunction with any other hardware or equipment other than the Product; 2. copy or modify all or any portion of the Software; 3. incorporate all (or any portion of) the Software into other programs developed or used by (or on behalf of) you;4. reverse engineer, decompile, decrypt or disassemble the Software (or any portion of the Software); or5. export, transfer or re-export the Software in violation of any applicable law.C. Open Source SoftwareCertain components of the Software are subject to either: (i) the GNU General Public Licence (“GPL”); (ii) the GNU Lesser General Public Licence (“LGPL”); or (iii) OpenSSL license. The foregoing are not subject to the restrictions in Section B. In compliance with the GPL and LGPL Pace makes the source code of the Linux software, libraries and associated utilities it uses, together with its modiﬁcations (if any), available to the public in source code form at: http://www.pace.com/opensource/request.

19You are free to use, modify and distribute the Linux software and any modiﬁcations as long as you comply with the terms of the GPL or LGPL referred to above. The License terms applicable to (i) to (iii) above are available to you, as explained in the section below entitled Open Source Licenses.The Software also contains the following: (iv) SHA library Copyright © 2000-2001, Aaron D. Gifford All rights reserved. (v) Expat XML Parsing Library Copyright © 1998, 1999, 2000 Thai Open Source Software Centre Ltd and Clark Cooper. Copyright © 2001, 2002, 2003 Expat maintainers.(vi) Expat++ This component of the Software is subject to the Mozilla Public License Version 1.0.(vii) Base64 Algorithm Copyright © 2001 Bob Trower, Trantor Standard Systems Inc.Certain additional license terms applicable to (iv) to (vi) above are available to you, as explained in the section below entitled Open Source Licenses.D. TerminationThese Terms are effective until terminated. You may terminate these Terms by returning the Product to your supplier. These Terms will terminate automatically without notice if you fail to comply with these Terms or any other written agreement between you and Pace. Upon termination you must return the Product to your supplier.E. Disclaimer1. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN YOU AND PACE (OR YOUR SUPPLIER), THE SOFTWARE IS (TO THE EXTENT PERMITTED BY LAW) SUPPLIED “AS IS” AND PACE AND ITS LICENSORS EXPRESSLY EXCLUDE ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING (BUT NOT LIMITED TO) WARRANTIES OF MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR PURPOSE AND NON-INFRINGEMENT. TERMS AND CONDITIONS FOR USE OF SOFTWARE (“TERMS”) (cont.)2. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN YOU AND PACE, IN NO CIRCUMSTANCE WILL PACE BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, PUNITIVE OR INCIDENTAL DAMAGE (INCLUDING LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA OR THE COST OF PROCUREMENT OF SUBSTITUTE GOODS, TECHNOLOGY OR SERVICES) ARISING OUT OF THE USE OR THE INABILITY TO USE THE SOFTWARE.F. GeneralThese Terms are governed by the laws of the State of New York and you may only bring claims exclusively in New York courts and Pace shall be entitled to bring a claim in the courts of any jurisdiction. Any failure by Pace to enforce any of its rights hereunder or applicable law shall not constitute a waiver of such rights. Pace’s licensors and suppliers shall be third party beneﬁciaries of this License Agreement, as applicable.YOUR USE OF THE PRODUCT CONSTITUTES YOUR ACKNOWLEDGEMENT THAT YOU HAVE READ THESE TERMS AND AGREE TO BE BOUND HEREBY.Open Source LicensesThe software contained in this product may be covered by certain components consisting of free software or open source software. A list of these components and a copy of the relevant copyright notices and license term notices that are required by such licenses are available at this web page: http://www.pace.com/opensource/license This list may change from time to time and may depend on the model of product or the version of software you have received. If you are unable to access this web page and wish to have a copy of this list, please contact the Open Source Administrator at: 3701 FAU Boulevard, Suite 200, Boca Raton, Florida 33431 USA. To the extent the terms of these open source or free software licenses prohibit any of the restrictions in any end user license included with the product, such restrictions will not apply to the applicable open source or free software component.

20NOTES

21NOTES

501-3443200Pace and are trademarks and/or registered trademarks of Pace plc.www.pace.com

Navigation menu