AMPAK Technology GT966X bluetooth module User Manual GT966X EVKits V2 0 20110919

AMPAK Technology Inc. bluetooth module GT966X EVKits V2 0 20110919

User Manual

AMPAK Technology Inc.    www.ampak.com.tw    Proprietary & Confidential Information i Doc. NO:          AMPAK  GT966X Evaluation Kits  User manual   Version 2.0     Revision History Date  Revision Content  Revised By Version 2011/09/24 Initial released    Andy  2.0
AMPAK Technology Inc.    www.ampak.com.tw    Proprietary & Confidential Information i Doc. NO:   Contents 1. GT966X evaluation board introduction..................................................................... 1 2. PIN Description........................................................................................................... 3 3333.      Federal Communication Commission Interference Statement.............................. 4
 AMPAK Technology Inc.    www.ampak.com.tw    Proprietary & Confidential Information   Doc. NO:  1 1. GT966X evaluation board introduction GT966X evaluation board (EVB) likes as figure1. That is designed for Bluetooth 2.1+EDR application. The bottom views like as figure2. It is also designed for TI’s MSP430 and TMX320C5X experimenter board. It is subject to provide a convenient environment  for  customer’s  verification  on  Bluetooth  function.  There  are controller pins on evaluation board which describes as below.   Figure1. Top view of GT966X EVB
 AMPAK Technology Inc.    www.ampak.com.tw    Proprietary & Confidential Information   Doc. NO:  2  Figure2. Bottom view of GT966X EVB    Interface highlights: 1.  U4: GT966X SIP module. 2.  S1: U.FL connector let RF signal in/out path, which R55 need tie on 0ohm. 3.  J10: VBAT::::  3V3 for main system power path. IO  ::::1V8 for system IO level path. S/M::::PCM mode (Jump onPCM slave mode. Jump offPCM master mode) 4.  J1&J2: For TI’s experimenter board IO used.
 AMPAK Technology Inc.    www.ampak.com.tw    Proprietary & Confidential Information   Doc. NO:  3 2. PIN Description  Connector No.  Pin Name  Def. Dir.  Description of Options (Common) J1  1,19  GND    Connect to ground   3  HCI_CTS_3V3  I  HCI UART clear-to-send   5  SLOW_CLK_3V3  I  32.768-KHz clock in   7  HCI_RX_3V3  I  HCI UART data receive   9  HCI_TX_3V3  O  HCI UART data transmit   others  Not connected     J2  2  GND    Connect to ground   7,9  +3V3  I  Connect to +3.3V   8  PCM_OUT_3V3  O  PCM data output   10  PCM_IN_3V3  I  PCM data input   11  PCM_FSYNC_3V3  I/O  PCM frame synch   17  PCM_CLK_3V3  I/O  PCM clock   18  HCI_RTS_3V3  O  HCI UART request-to-send   19  nSHUTD_3V3  I  Shutdown input (active low)   others  Not connected
 AMPAK Technology Inc.    www.ampak.com.tw    Proprietary & Confidential Information   Doc. NO:  4 3333.      Federal Communication Commission Interference Statement  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.    These limits are designed to  provide  reasonable  protection  against  harmful  interference  in  a  residential installation.  This  equipment  generates,  uses  and  can  radiate  radio  frequency energy  and,  if  not  installed  and  used  in  accordance  with  the  instructions,  may cause  harmful  interference  to  radio  communications.    However,  there  is  no guarantee  that  interference  will  not  occur  in  a  particular  installation.    If  this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  -  Reorient or relocate the receiving antenna. -  Increase the separation between the equipment and receiver. -  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -  Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: Any changes or modifications not expressly approved by the party responsible  for  compliance  could  void  the  user's  authority  to  operate  this equipment.  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  Radiation Exposure Statement: This  equipment  complies  with  FCC  radiation  exposure  limits  set  forth  for  an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
 AMPAK Technology Inc.    www.ampak.com.tw    Proprietary & Confidential Information   Doc. NO:  5 This device is intended only for OEM integrators under the following conditions:  1)  The antenna must be installed such that 20 cm is maintained between the antenna and users, and   2)  The transmitter module may not be co-located with any other transmitter or antenna.    As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed  IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.  End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: ZQ6-GT966X”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.  Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu