ADC Telecommunications FWM0801A GSM Base Station User Manual Manual 2

ADC Telecommunications Inc GSM Base Station Manual 2

Contents

Manual 2

FlexWave microBTS Installation and Commissioning Guide Page 55© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration5.5 Assigning OML Link IP Address and a Static IP Address to the microBTS Depending upon your networks requirements, a network IP address will need to be assigned to the microBTS and each TRX. IP addresses should be obtained from your network administra-tor. Use the following step-by-step procedure to assign a new IP address to the microBTS.1 Find the IP address of the microBTS corresponding to the micro controller. The last MAC address listed on the exterior label will be the micro controller as shown in Figure 5-7. Match this MAC address with the DHCP assigned IP address as shown in Figure 5-12. Open a Web browser such as Explorer, Mozilla, etc. and using the familiar browser command: http:// xxx.xxx.xxx.xxx where xxx.xxx.xxx.xxx is the IP address assigned to the micro controller.The following screen will appear. Refer to Figure 5-15.Figure 5-15: FlexWave microBTS Configuration ScreenAD030908
Page 56 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration2 Using the configuration screen, type in the following information as shown in Table 5-1ETable 5-1: Configuration ParametersParameter VariablemicroBTS Address Use an IP address assigned by your system administratorSubnet Mask Use an IP address assigned by your system administratorGateway Use an IP address assigned by your system administratornanoBTS 1 Use an IP address assigned by your system administratornanoBTS 2 Use an IP address assigned by your system administratorPrimary OML (operations and maintenance link) 1 Use the IP address assigned to the Abis link on which your BSC is operatingPrimary OML (operations and maintenance link) 2 Use the IP address assigned to the Abis link on which your BSC is operating a secondary linkUse DHCPThis is selected when a DHCP address needs to be assigned to the microBTS. Make sure that this is not selected if you are assigning static IP addresses
FlexWave microBTS Installation and Commissioning Guide Page 57© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration5.6 Configuring a New Site Using the BSC Configuration Manager UtilityOnce the microBTS is configured with IP addresses, use the following procedure to launch, configure and verify that the microBTS is connected and functioning.1 Launch the BSC Configuration Manager from the PC’s desktop or file folder as shown in Figure 5-16.Figure 5-16: Launching the BSC Configuration Manager from a PC DesktopAD069909Launch theBSC configurationManager
Page 58 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration2 After the BSC Configuration Manager is launched, a connection screen will appear as shown in Figure 5-17. Type in the IP address of the BSC you wish to communicate with. Enter the password and click OK.3 A “tree” representation of your network will appear as shown in Figure 5-18. Click on the sites + symbol. This will show each BTS site on your network. Figure 5-17: Connecting to the BSC screenFigure 5-18: Reviewing the BTS Sites on the NetworkAD069902AD069903Click on the Sites “+”SymbolTo Reveal the BTS Sites onthe Network
FlexWave microBTS Installation and Commissioning Guide Page 59© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration4 A new site must be created for the microBTS configured in the previous sections. Right click on Sites and select Create. A Create SITE dialog box will appear as shown in Figure 5-19.5 A number of parameters will need to be input in the Create SITE dialog box as shown in Table 5-2:EFigure 5-19: Creating a New SiteTable 5-2: Configuration ParametersParameter VariableBTS Class From this pull-down menu, select the type of TRX(s) installed in the microBTSSite Name Select a site name according to the needs of your networkSite IndentifierThis number is normally assigned by a network admin-istrator depending upon the needs of the network. The number must be unique to each site and can not be duplicated within a network.AD069905
Page 60 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration6 Once all of the above items are configured, click Finish and a new BTS site will be created.7 A new site will appear in the configuration “tree.”Note: For 2 x 1 configured microBTS a “slave TRX” must be added. 8 Right click on the site object and select Create from the pull-down menu. 9A Create BTS Child Object screen will appear. Select Create TRX objects and click on OK. Refer to Figure 5-20. BTS Name Select a BTS name that is associated to the site name in your networkFrequency Band Select the appropriate frequency band from the pull-down menuMCC Select an AFRCN channel number according to the needs of the networkMNC Per network requirementLocation Area Code (LAC) Per network requirementCell Identity Per network requirementPLMN-CC Per network requirementBS-CC Per network requirementFigure 5-20: Create BTS Child Object ScreenTable 5-2: Configuration ParametersParameter VariableAD079901
FlexWave microBTS Installation and Commissioning Guide Page 61© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration10 A Create TRX screen will appear. Refer to Figure 5-21. 11 Fill in the dialog boxes with the information appropriate to your system. Refer to Table 5-2.E12 Once this information is added.13 Click Finish to complete the process of adding a slave TRX. Table 5-3: Configuration ParametersParameter VariablenanoBTS Hardware Class From this pull-down menu, select the type of TRX(s) installed in the microBTSRadio Carrier Name Select a Radio Carrier Name according to the needs of your networkBaseband Transceiver Name Select a Baseband Transceiver Name according to the needs of your networkTRX Number In a 2 TRX system the Master = 0, the Slave = 1.Figure 5-21: Create TRX ScreenAD079902
Page 62 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration5.7 Creating the FlexWave Manager1 Right click on the FlexWave Manager object on the “tree” screen as shown in Figure 5-22. Select Create from the pull-down menu.2A Create microBTS screen will appear.3 Enter the name (the name will be choosen according to the needs of your network)and site identifier (the serial number located on the exterior label of the microBTS) in the dialog boxes indicated. Click Edit once the information is input. Refer to Figure 5-23.Figure 5-22: Using the FlexWave Manager Object to Launch the Create TRX ScreenAD079903
FlexWave microBTS Installation and Commissioning Guide Page 63© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration4A Sites belonging to this microBTS dialog screen will appear. The site name entered in the previous steps will appear in the top portion of the screen. 5 Click on the new site to highlight it.6 Click on the down arrow to move this site into the SITEs in this microBTS: shown on the lower portion of the screen and click OK. Refer to Figure 5-24.Figure 5-23: Create TRX ScreenFigure 5-24: Sites Belonging to this microBTS ScreenAD079904AD079906
Page 64 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration7 A confirmation screen will appear that indicates the created site has been moved into the FlexWave Manager register. Refer to Figure 5-25.8 Return to the Create microBTS screen as shown in Figure 5-23 and click Finish. 9 Return to the main screen and the new FlexWave Manager site object will appear as shown in Figure 5-26. Figure 5-25: Conformation SITEs Belonging to this ScreenAD079907
FlexWave microBTS Installation and Commissioning Guide Page 65© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration10 Right click on the new site and select Properties. A configuration screen titled microBTS- (name of model) Properties... will appear. Select the Configuration tab. Refer to Figure 5-27.Figure 5-26: New Site Object Appears on Configuration Manager “Tree”AD079909
Page 66 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration11 Verify the serial/ identification number from the exterior model label of the microBTS matches the one obtained in Step 2. 12 Click on the FlexWave IP Address List Edit button and enter the OML Link IP address for your network. Click OK. Refer to Figure 5-28.Figure 5-27: Configuration Tab of the Site Properties ScreenFigure 5-28: Verifying the FlexWave IP Address ListAD075904AD078902
FlexWave microBTS Installation and Commissioning Guide Page 67© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration13 Click on the Primary OML Address List Edit button and enter the OML Link IP address for your network. Click OK. Refer to Figure 5-29.Figure 5-29: Verifying the Primary OML Address ListAD078903
Page 68 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Chapter 5 - microBTS Initial Configuration5.8 Verifying BTS Functionality Using the BSC Configuration ManagerTo verify the installed BTS is functioning, use the following procedure:1 Right click on the new site shown on the BSC Configuration Manager “tree” and a dialog box will appear. Select Unlock.The BTS will now begin transmitting on the AFRCN number selected in the previous steps. This can be verified at the site by means of an external power meter and frequency counter or a spectrum analyzer if available. Make a phone call by working in conjunction with the system administrator.Note: Further information regarding the configuration of the microBTS TRX units can be found in the instructions set forth in ADC publication ADCP-75-310
FlexWave microBTS Installation and Commissioning Guide Page 69© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade ProcedureAppendix A - Software Upgrade ProcedureA.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70A.2 Upgrading Micro Controller Software from 4.0.x.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71A.2.1 Automatic Upgrading of the microBTS Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71A.2.2 Manual Upgrade Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78A.3 Upgrade Procedure for Micro Controller Software 3.2.x to Version 4.0.1.x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Content Page
Page 70 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade ProcedureA.1 IntroductionFrom time-to-time ADC may issue software upgrades in the interest of product improvement. The following upgrade procedure should be performed by an experienced field service techni-cian who is familiar with linux operating systems. Caution: Failure to execute the procedure(s) exactly as given may render the microBTS inoperative.
FlexWave microBTS Installation and Commissioning Guide Page 71© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade ProcedureA.2 Upgrading Micro Controller Software from 4.0.x.xThe micro controller unit within the microBTS contains upgradable software, which from time-to-time may be upgraded.This procedure provides two methods for upgrading the micro controller software. An “auto-matic” upgrade (preferred method) is accomplished through the use of a GUI type interface. The “manual” procedure relies on linux commands to accomplish the upgrade task. The “manual” upgrade method should only be used when circumstances preclude the use of the “automatic” upgrade and should be performed by an experienced linux operator.A.2.1 Automatic Upgrading of the microBTS Controller 1 Launch a WinSCP session from the PC desktop and the WinSCP Login screen will appear. Refer to Figure A-1.2Enter the Host name which is the IP address assigned to the micro controller unit of the microBTS being upgraded. 3Enter root in the User name dialog box, and your password in the Password dialog box. 4 Click on Login when complete.Note: The following procedure will require that the microBTS being upgraded be taken out of service for the duration of the upgrade process.Figure A-1: WinSCP Login ScreenAD091911
Page 72 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure5A Warning screen will appear (if this is your first login). Select Yes. Refer to Figure A-2.6A Server prompt screen will appear. Enter your Password in the dialog box indicated and click OK. Refer to Figure A-3.Figure A-2: WinSCP Warning ScreenFigure A-3: WinSCP Server Prompt ScreenAD091912AD091913
FlexWave microBTS Installation and Commissioning Guide Page 73© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure7 The main WinSCP will appear showing the contents of the drive on which the compressed .gz upgrade file is located and the root directory showing the files currently contained in the microBTS controller. Copy the upgrade files similar to FWBSSCtrl_4.0.x.x.gz to the root directory. Refer to Figure A-4.8 Close the WinSCP window and open a PuTTY session with the BSC by entering the BSC IP address. Login as root. Enter your password. Refer to Figure A-5.Figure A-4: Main WinSCP ScreenAD091903C: ADC
Page 74 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure9 At the command prompts, type the following commands: cd /var/lib/ipaccess/supportls -lRefer to Figure A-6.Figure A-5: PuTTY Login ScreenFigure A-6: Entries on Command LineAD091904AD091905
FlexWave microBTS Installation and Commissioning Guide Page 75© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure10 At the command line, type the following commands: cp /root/FWBSSCtrl_4.0.x.x.gz .ls -l Refer to Figure A-7.11 Close the PuTTY window and launch BTS Configuration Manager. 12 Select Connect to BSC from the task bar.13 Enter the IP address of the BSC and click OK. Refer to Figure A-8.Figure A-7: PuTTY Login ScreenAD091906
Page 76 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure14 Right click on the FlexWave Manager object and select Properties. The FlexWave Manager Properties screen will appear. Verify that the nanoBTS Software Version dialog box contains the updated software version number. Refer to Figure A-9.will Figure A-8: Connect to BSC ScreenFigure A-9: FlexWave Manager Properties Screen Confirming the New Software LoadAD091907AD091908
FlexWave microBTS Installation and Commissioning Guide Page 77© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure15 Return to the BSC Configuration Manager screen and find the BTS upgraded on the configuration “tree.”16 Right click on the site and select Properties. The microBTS Properties screen will appear (this may take up to 10 minutes) showing the Active Software Version and the Standby Software Version. 17 Confirm the Standby Software Version is the version loaded on this procedure. After determining it is correct, Click OK. Refer to Figure A-10.will 18 Return to the BSC Configuration Manager main screen and select BSC Control from the menu bar as shown in Figure A-11. 19 With the FlexWave Manager Object still selected, select Activate nanoBTS Software from the drop down menu.20 When prompted to activate the new software click OK.Figure A-10: microBTS Properties Screen Confirming the Active and Standby Software Loads4.0.1.9AD091909
Page 78 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedurewill 21 The microBTS is now upgraded with the new software load. The site can now be returned to normal operation.A.2.2 Manual Upgrade ProcedureUpgrading of the micro controller software can be done using a procedure using linux commands to accomplish the upgrade task. The manual upgrade method should only be used when circumstances preclude the use of the “automatic” upgrade and should be performed by an experienced linux operator. Use the following step-by-step procedures:1 Launch a WinSCP session from the PC desktop and the WinSCP Login screen will appear. Refer to Figure A-12. 2 Enter the Host name which is the IP address assigned to the micro controller unit of the microBTS being upgraded. 3Enter root in the User name dialog box, and your password in the Password dialog box. Click on Login when complete.Figure A-11: Activating the nanoBTS Software From the BSC Configuration Manager Main ScreenAD091910
FlexWave microBTS Installation and Commissioning Guide Page 79© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure4A Warning screen will appear. Select Yes. Refer to Figure A-13.5A Server prompt screen will appear. Enter your Password in the dialog box indicated and click OK. Refer to Figure A-14.Figure A-12: WinSCP Login ScreenFigure A-13: WinSCP Warning ScreenAD091911AD091912
Page 80 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure6 The main WinSCP will appear showing the contents of the drive on which the compressed .gz upgrade file is located and the root directory showing the files currently contained in the microBTS controller. Copy the upgrade files which will appear similar to FWBSSCtrl_4.0.x.x.gz to the root directory. Refer to Figure A-15.Figure A-14: WinSCP Server Prompt ScreenAD091913
FlexWave microBTS Installation and Commissioning Guide Page 81© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure7 Close the WinSCP window and open a PuTTY session with the BSC by entering the BSC IP address. Login as root. Enter your password. Open a PuTTY session and login as root.8 At the command line enter:hcp -v This will display the current version of the micro controller software. For example:hcp: version 4.0.1.39 At the command prompt enter: ls -l Figure A-15: Main WinSCP ScreenAD091903C: ADC
Page 82 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade ProcedureThe output will appear similar to the following:total 105-rw-r--r-- 1 root root 95965 2009-03-11 01:36 FWBSSCtrl_4.0.1.9.gz-rw-r--r-- 1 root root 1 2009-03-10 22:23 gothcp-rw-r--r-- 1 root root 2485 2009-03-10 22:43 got_info10 At the command line enter:cd /usr/local/sbinlsText similar to the following will appear showing the various files in the directory:batch.pem changeHcpVersion cluster_000810164.tgz hcpca.pem cluster_000810156.tgz cluster-cert.pem oem.pemcertChainFile.pem cluster_000810158.tgz cluster-key.pem11 Make a temporary directory: mkdir tmp 12 Change to the temporary directory by entering:cd tmp13 At the command line enter:To copy the upgrade file to the temporary directorycp /root/FWBBSSCtrl_4.0.1.9.gz 14 To unpack the tar file, type:tar -zxvf FWBSSCtrl_4.0.1.9.gzThe following output will appear:adc.GIFhcphcpInstallmicroBTSupdatePod15 Install the upgrade files by entering:./hcpInstall The following output will appear:
FlexWave microBTS Installation and Commissioning Guide Page 83© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedureln: `/var/www/index.html': File existsStopping hardware control process: hcp.16 To change directories enter:cd .. 17 At the command line enter: hcp -v This will display the version number of the software upgrade loaded in this procedure. For example:hcp: version 4.0.1.918 This completes the manual upgrade procedure. Verify the new software is loaded by Closing the PuTTY window and launching BSC Configuration Manager. Select Connect to BSC from the task bar. Enter the IP address of the BSC and click OK. Refer to Figure A-16.19 Right click on the FlexWave Manager object and select Properties. The FlexWave Manager Properties screen will appear. Verify that the nanoBTS Software Version dialog box contains the updated software version number. Refer to Figure A-17.Figure A-16: Connect to BSC ScreenAD091907
Page 84 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedurewill 20 Return to the BSC Configuration Manager screen and find the BTS upgraded on the configuration “tree.”21 Right click on the site and select Properties. 22 The microBTS Properties screen will appear showing the Active Software Version and the Standby Software Version. Confirm the Standby Software Version is the version loaded in this procedure. 23 After determining it is correct, Click OK. Refer to Figure A-18.Figure A-17: FlexWave Manager Properties Screen Confirming the New Software LoadAD091908
FlexWave microBTS Installation and Commissioning Guide Page 85© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedurewill 24 The manual upgrade of the microBTS controller is now complete.Figure A-18: microBTS Properties Screen Confirming the Active and Standby Software Loads4.0.1.9AD091909
Page 86 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade ProcedureA.3 Upgrade Procedure for Micro Controller Software 3.2.x to Version 4.0.1.x.Use the following “manual” upgrade procedure to upgrade microBTS controller software from version 3.2.x to 4.0.1.x.1 3.2.x versions of the micro controller software will not display IP or MAC addresses on the BTS Installer Utility. The MAC and IP addresses for the micro controller can be found using the following methods:2 Launch the BTS Installer Utility as shown in Figure A-19 and click on the Find button.3A Select nanoBTS screen will appear. The MAC and IP addresses of the nano TRX’s with in the microBTS will be shown. Refer to Figure A-20. Figure A-19: Selecting Find on the BTS Installer UtilityAD098901
FlexWave microBTS Installation and Commissioning Guide Page 87© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure4 Confirm that the MAC addresses shown match those shown on the exterior label of the microBTS. The IP address for the micro controller is normally one digit higher than the highest IP address of the nano TRX’s. In the sample shown, the highest nano TRX is 172.16.79.15. It is likely that the micro controller address will be 172.16.79.16. Record this number for use in the next step.5 Use the IP address from the previous step to launch the WinSCP session in the next step. If the IP address does not work, use Wireshark, Angry IP or similar IP discovery tool to obtain the micro controller IP address.6 Launch a WinSCP session from the PC desktop and the WinSCP Login screen will appear. Refer to Figure A-21. 7Enter the Host name which is the IP address assigned to the micro controller unit of the microBTS being upgraded. 8Enter root in the User name dialog box, and your password in the Password dialog box. 9 Click on Login when complete.Figure A-20: Select nanoBTS Screen Showing the MAC and IP Addresses for the nano TRX’s172.16.79.14172.16.79.1500:02:95:00:42:1700:02:95:00:42:AD1/0/02/0/0AD098902
Page 88 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure10 A Warning screen will appear. Select Yes. Refer to Figure A-22.11 A Server prompt screen will appear. enter your Password in the dialog box indicated and click OK. Refer to Figure A-23.Figure A-21: WinSCP Login ScreenFigure A-22: WinSCP Warning ScreenAD091911AD091912
FlexWave microBTS Installation and Commissioning Guide Page 89© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure12 The main WinSCP will appear showing the contents of the drive on which the compressed .gz upgrade file is located and the root directory showing the files currently contained in the microBTS controller. Copy the upgrade files which will appear similar to FWBSSCtrl_4.0.x.x.gz to the root directory. Refer to Figure A-24.Figure A-23: WinSCP Server Prompt ScreenFigure A-24: Main WinSCP ScreenAD091913C: ADC
Page 90 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure13 Close the WinSCP window and open a PuTTY session with the BSC by entering the BSC IP address. Login as root. Enter your password. Refer to Figure A-25.14 At the command line enter:cd /usr/local/sbinlsText similar to the following will appear showing the various files in the directory:batch.pem changeHcpVersion cluster_000810164.tgz hcpca.pem cluster_000810156.tgz cluster-cert.pem oem.pemcertChainFile.pem cluster_000810158.tgz cluster-key.pem15 Make a temporary directory: mkdir tmp 16 Change to the temporary directory by entering:cd tmp17 To copy the upgrade file to the temporary directorycp /root/FWBBSSCtrl_4.0.1.x.gz 18 To unpack the tar filetar -zxvf FWBSSCtrl_4.0.1.x.gzFigure A-25: PuTTY Login ScreenAD091904
FlexWave microBTS Installation and Commissioning Guide Page 91© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade ProcedureThe following output will appear:adc.GIFhcphcpInstallmicroBTSupdatePod19 Display the software version number by entering:hcp -v This will display the current version of the micro controller software. For example: hcp: version 3.2.720 Back up /etc/inventory files by changing directory to the etc directory. In the etc directory enter:tar -cvf /root/inventory.tar /etc/inventory21 At the command prompt enter:cd /etc22 Using a text editor such as vi modify the file in the /etc/inittab by commenting out the last line which should appear similar to this:#hcp:2:respawn:/usr/local/sbin/hcp -nondaemon If this line does not exist in the files proceed to the next step.23 At the command prompt enter:telinit q This will stop the hcp (micro controller process).24 Change the directory by entering:cd thttpd25 Verify the /etc/thttpd/thttpd.conf. Using a text editor such as vi, comment out the chroot line and changing the cgipat line at the bottom to include 2 asterisks instead of one: cgipat=/cgi-bin/**26 Change the directory to by entering:cd / var /www27 List the contents of the directory by entering:ls -l28 If no directory exists, create one by entering:
Page 92 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Proceduremkdir cgi-bin29 Open the cgi-bin directory by entering:cd cgi-bin30 Copy the contents by entering:cp /usr/local/sbin/tmp/* .31 Change directories by entering:cd /var/www32 Create a cgi-bin subdirectory in the /var/www directory and place the three files from the Html sub-project “microBTS”, “updatePod”, and “adc.GIF” into the cgi-bin directory.33 At the :/etc/thttpd# prompt enter: cd /var/www34 Display the contents of the directory by entering: ls -l35 The screen will now show: total 2drwxr-xr-x 2 root root 1024 2009-04-08 01:26 cgi-binlrwxrwxrwx 1 root root 16 2009-04-08 01:26 index.html -> cgi-bin/microBTSdrwxr-xr-x 2 root root 1024 2006-10-31 11:50 users36 At the :/var/www# prompt enter:cd cgi-bin/37 At the :/var/www/cgi-bin# prompt enter: ls -lThe screen will now show:total 44-rwxr--r-- 1 root root 1690 2009-03-10 18:36 adc.GIF-rwxr-xr-x 1 root root 18517 2009-03-10 18:36 microBTS-rwxr-xr-x 1 root root 21191 2009-03-10 18:36 updatePod38 Change the privledges on the ADC gif file by entering:chmod 744 adc.GIF39 Change the privledges on the microBTS file by entering:chmod 775 microBTS
FlexWave microBTS Installation and Commissioning Guide Page 93© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure40 Change the privledges on the updatepod file by entering:chmod 775 updatePod41 At the :/var/www/cgi-bin# prompt enter: ls -l42 The screen will now show (make sure that the files shown have the permissions as listed below):total 44-rwxr--r-- 1 root root 1690 2009-03-10 18:36 adc.GIF-rwxrwxr-x 1 root root 18517 2009-03-10 18:36 microBTS-rwxrwxr-x 1 root root 21191 2009-03-10 18:36 updatePod43 Change the directory by entering:cd /etc44 Modify the /etc/inittab back to its original state. Using a text editor such as vi works uncomment the last line so it appears as: 45 At the command prompt enter:cd /usr/local/sbinlsText similar to the following will appear showing the various files in the directory:batch.pem changeHcpVersion cluster_000810164.tgz hcpca.pem cluster_000810156.tgz cluster-cert.pem oem.pemcertChainFile.pem cluster_000810158.tgz cluster-key.pem46 Make a temporary directory by entering:mkdir tmp47 Change to the temporary directory by entering:cd tmp48 Copy the upgrade package by entering:cp /root/FWBBSSCtrl_4.0.1.x.gz .49 Unpack the upgrade package by entering:tar -zxvf FWBSSCtrl_4.0.1.x.gz
Page 94 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade ProcedureThe following output will appear:adc.GIFhcphcpInstallmicroBTSupdatePod50 At the command prompt enter:./hcpInstall The following output will appear:ln: `/var/www/index.html': File existsStopping hardware control process: hcp.51 At the command prompt enter:hcp -v This will display the version number of the software upgrade loaded in this procedure. For example:hcp: version 4.0.1.x52 This completes the manual upgrade procedure. Verify the new software is loaded by closing the PuTTY window and launching BTS Installation Manager. 53 Select Connect to BSC from the task bar.54 Enter the IP address of the BSC and click OK. Refer to Figure A-26.
FlexWave microBTS Installation and Commissioning Guide Page 95© 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure55 Right click on the FlexWave Manager object and select Properties. The FlexWave Manager Properties screen will appear. Verify that the nanoBTS Software Version dialog box contains the updated software version number. Refer to Figure A-27.will 56 Return to the BSC Configuration Manager screen and find the BTS upgraded on the configuration “tree.” Right click on the site and select Properties.Figure A-26: Connect to BSC ScreenFigure A-27: FlexWave Manager Properties Screen Confirming the New Software LoadAD091907AD091908
Page 96 FlexWave microBTS Installation and Commissioning Guide © 2009, ADC Telecommunications, Inc.ADCP-77-086 • Issue 2 • 04/2009 • Appendix A - Software Upgrade Procedure57 The microBTS Properties screen will appear showing the Active Software Version and the Standby Software Version. Confirm the Standby Software Version is the version loaded in this procedure. After determining it is correct, Click OK. Refer to Figure A-28.will Figure A-28: microBTS Properties Screen Confirming the Active and Standby Software Loads4.0.1.9AD091909
ADCP-77-086 • Issue 1 • 10/2008 • Back CoverFlexWave microBTS Installation and Commissioning Guide Page 97© 2009, ADC Telecommunications, Inc.Blank
13944-PContents herein are current as of the date of publication. ADC reserves the right to change the contentswithout prior notice. In no event shall ADC be liable for any damages resulting from loss of data,loss of use, or loss of profits and ADC further disclaims any and all liability for indirect, incidental,special, consequential or other similar damages. This disclaimer of liability applies to all products,publications and services during and after the warranty period.REPRINTS:www.adc.com/manualsPDF copies of manuals are availablefor downloading at the following link:PRODUCT INFORMATION AND TECHNICAL ASSISTANCE:connectivity.tac@adc.comwireless.tac@adc.comeuro.tac@adc.comasiapacific.tac@adc.comADCP Number:WRITE:ADC Telecommunications (S’PORE) PTE, LTD;100 Beach Road, #18-01, Shaw Towers.Singapore 189702.ADC Telecommunications, INCPO Box 1101,Minneapolis, MN 55440-1101, USAADC European Customer Service, INCBelgicastraat 2,1930 Zaventem, BelguimPHONE:U.S.A. or CANADASales: 1-800-366-3691 Extension 73000Technical Assistance: 1-800-366-3891 Connectivity Extension: 73475 Wireless Extension: 73476EUROPESales Administration: +32-2-712-65 00Technical Assistance: +32-2-712-65 42EUROPEAN TOLL FREE NUMBERSGermany: 0180 2232923UK: 0800 960236Spain: 900 983291France: 0800 914032Italy: 0800 782374ASIA/PACIFICSales Administration: +65-6294-9948Technical Assistance: +65-6393-0739ELSEWHERESales Administration: +1-952-938-8080Technical Assistance: +1-952-917-3475 ADCP-77-086
Website: www.adc.com

Navigation menu